Search Documents

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Esso-BHP have installed a Production Supervisory Control System that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control. The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexability to handle future variations in operating conditions. Thn -etom ..ill kn nvt,,ndnd to thn I-lalihn+ rJ,+f, rr , Into +hie -- -A +n the lei...,fieh .,lo+fnrmc A.,;- 1071

Jan 1, 1970

The Honourable Neil Pickard has been in Parliament for something like sixteen years. He was Minister for Education in 1976, served as Shadow Minister in a number of portfolio areas while his party was in opposition, and since their return to power in 1988, he has been the Minister for Minerals and Energy. Ladies and gentlemen, I ask you to welcome the Minister, the Honourable Neil Pickard.

Jan 1, 1989

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By M Brewster

Goldfields Abosso Goldfields Limited (AGL) is a Ghanaian registered company that owns and operates the Damang Gold Mine. Gold Fields Ghana Holdings Limited holds a 71.1 per cent interest in AGL. The Damang concession held by Gold Fields Ghana Holdings Limited covers a total area of 271 km2 located 40 km north of the town of Tarkwa in the south-western part of Ghana. Gold Fields as a company registered on the New York Stock Exchange is legally obliged to be SOX (Sarbanes-Oxley). Sarbanes-Oxley Section 404 (SOX404) is on management assessment of internal controls. The Mineral Resource Management (MRM) function of AGL manages three Prospecting Licenses and two mining licences. At least ten pits/prospects are scattered along the two limbs of the Damang Anticline and have two main types of mineralisation notably Paleoplacer and Hydrothermal. Thus SOX404 procedures are put in place to treat each mineralisation type in the best way for reliable resource outputs and estimates. Generating auditable resources for AGL is a prime but most important function of MRM. Thus important checks are built and designed to ensure that all relevant geological and geostatistical inputs conform to procedures outlined under SOX404 requirements. More importantly sign offs are designed to ensure that technical personnel involved in all aspects of resource and reserve generation are satisfied and can be held accountable.

Jan 1, 2007

This brief overview of the history of Brown Coal mining in Victoria is a luncheon presentation -I do not intend to make it indigestible with extensive listings of resources or production. There is a vast pantry of collated historical records and of vari- ous predictive studies available for the enquired with a hearty digestion. A gourmet collation is provided in The Aus IMM Monograph No 11 published in 1984 entitled "Victoria's Brown Coal-A HUGE FORTUNE IN CHANCERY", currently still on offer by the Institute and available at a bargain price in the foyer at this conference. Monograph No 11 also provides a feast of excellent references on the theme of Victorian Brown Coal assembled by the several contributors. In contrast, my presentation paper is a fast-food service, extracts from the printed paper only-you have no choice-you "get what you get" and in small quantity. I hope it will tantalise your appetite -like Oliver Twist you will ask for more. -Buy the Monograph!

Jan 1, 1989

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

The Peko copper orebody is associated with a body of magnetite rock which it has partly replaced. The primary ore averages about 9 per cent. copper and 4 dwt. gold per ton and locally IS much richer. It consists essentially of chalcopyrite and unreplaced magnetite, with lesser amounts of pyrite, marcasite, pyrrhotite, cobaltite, bismuthinite, native bismuth and native gold. The earliest formed mineral is wolfram, and the latest formed is goethite, so that the temperature of deposition ranged from about 5000 C. to 1650 C. or lower.Oxidation extends to 270 ft., which is 100 ft. below the present water level. The oxidized ore consists of cuprite and native copper, and has replaced more or less massive chalcocite of a former zone of secondary sulphide enrichment. The present zone of secondary sulphide enrichment extends from about 270 ft. to 310 ft. depth.INTRODUCTIONThe Peko mine is about 6 miles south-west of Tennant Creek township in the Northern Territory, adjacent to a small outcrop of hematite rock that projects above an otherwise featureless "bull-dust" fiat.The copper-gold orebody being developed in this mine did not outcrop. It was first detected in 1950 by a surface diamond-drill hole (DDH.1), which intersected primary copper ore at a depth of 400 to 425 ft. This ore contained from 4 to 11 per cent. copper and 1 to 25 dwt. gold per ton. Since then a shaft has been sunk, and crosscuts and development drives have been opened on the 210..ft., 300-ft. and 400-ft. levels, which are also connected by winzes. Two diamond drill holes sunk from the 400-ft. level have intersected theorebody at about 450 to 460 ft., and a winze from the 400-ft. level intersected the lode from 445 to 500 ft. At this point it is 54 ft. wide, and averages 9 per cent. copper. More recently an inclined surface drill hole (Peko No. 1) has cut the lode at 856 ft. to 921 ft., equivalent to a vertical depth...

Jan 1, 1955

Limnological processes are often overlooked when trying to assess the long-term water quality of pit lakes. It is essential to deal with these aspects, since they determine the geochemical and redox conditions around the submerged reactive rocks. Underground mining at East Sullivan (northwestern Quebec, Canada) stopped in 1966. Two adjacent stopes, 91 and 106 m deep, were left open to the surface, with roughly circular apertures of about 7700 and 18 000 m2. Water filling of the two glory holes went on over three decades and overflow began in 1999. Surface water pHs values were near neutrality as late as 1994 (6.3 - 7.0) but had become acidic by 1999 (2.6 - 3.5). Limnological processes were investigated in late-1999 and early-2000, with temperature measurements at 1 m intervals and sampling of the water columns before and after the late fall density inversions. A strong chemocline-thermocline was observed at 15 m. Above the chemocline, the water had low pH (3.2), no alkalinity, and low Na, Ca and sulfate. Below the chemocline, the concentrations of these parameters and the pH increased, with pH at 5.5 - 6. Consistent with the low pH values present in the upper 15 m, the concentrations of Al, Cd, Cu, and Zn were high near surface, and decreased below the chemocline. Dissolved oxygen concentrations as well as Eh decreased with increasing depth. Alkalinity integrated over the entire water column below the chemocline was at least six times larger than the acidity inferred from Fe2+ and Fe3+ concentrations. The temperature survey showed that seasonal density inversions do occur in the water column. The inversions do not involve the entire water body, since the surface to depth ratio is too small for a complete overturn. Oxygen from surface waters is carried to the bottom where it oxidises sulfides, until its depletion. Residual Fe2+, stable under anoxic conditions, is displaced upward by the next dense water incursion. It eventually reaches the thermocline, but only after many successive incursions. There, its oxidation to Fe3+ allows hydrolysis, which consumes dissolved and wall-rock alkalinity. It is only in 1999 that alkalinity was finally exhausted and that the pH shifts to acid values. The low pHs in the surface waters allow a build up of Fe3+ and Al3+, and desorption of metals from colloids. Buffering is assumed to be controlled by wall-rock oxyhydroxides in surface waters, and by carbonate minerals in the bottom waters. Because the seasonal overturns are far from being complete, the large amounts of alkalinity acquired from the wall-rock in the bottom waters cannot balance the acidity of near surface waters. Hence the surface water is acidic.

Jan 1, 2003

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

By Valenta R. K

A technique is presented for the integrated forward modelling of the three-dimensional structure and the geophysical response of multiply deformed terrains. This technique allows information collected by field geologists and geophysicist to be reconciled by the development of a simplified kinematic structural history of the area. The structural modelling simulates the deformation history of the area in terms of a succession of structural events, such as folds, shear zones and intrusions. The interaction of these events with a starting stratigraphy results in the prediction of the geometry of the structures. By specifying geophysical rock properties for the units in the initial stratigraphy predictions are possible for the potential field anomalies for gravity and magnetics. This approach is suited to a range of applications, and its uses in the modelling of regional structures, testing of geophysical data processing, volume balancing, multiply constrained inversion and training are discussed.

Jan 1, 1995

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

By Osorio J. D C, McMahon M. D

Burwood Beach Sewage Ocean Outfall is being constructed by the Hunter District Water Board as part of an amplification scheme to eliminate pollution from adjacent bathing beaches. The outfall consists of a 93m vertical shaft, 1950m of 2.7m diameter tunnel with a series of diffuser outlets connecting the seaward end of the tunnel to the sea floor on a rock outcrop. The site of the work is in the Newcastle Coal Measures and the project is complicated by the proximity of colliery workings to tunnel alignment, although the colliery records provided valuable information on geological features. The location of the tunnel was determined to be in the Waratah Sandstone Formation immediately below the colliery workings after three different alternatives were considered. The shaft, which will be sized to suit contractor's construction methods and equipment, will be sunk through about 24.5m of alluvial material and 68.5m of rock. The tender documents were developed to allow the contractor considerable flexibility in construction method to suit available equipment. The specification also allowed great flexibility in tunnel construction method with minimum cross sectional area of 5.7m2 being the basis for a number of allowable alternative profiles ranging from circular to horseshoe.

Jan 1, 1987

By P Joyce, A S. Ray, P S. Thomas, J Haggman

Climate change and global warming present a significant challenge as unsustainable levels of greenhouse gas emissions arising from human activities continue to be emitted. The cement industry is responsible for between five and ten per cent of annual world carbon dioxide emissions; most arising from the manufacture of Portland cement (PC). An effective way of reducing emissions is by incorporating supplementary cementitious materials (SCMs) as partial PC replacements. SCMs are silicate or aluminosilicate based pozzolanic materials which, in finely divided form, combine with water and calcium hydroxide (lime), liberated by cement hydration, to form compounds exhibiting cementitious properties. Pitchstone is such an aluminosilicate and has the potential to act as an effective pozzolan for partial replacement of PC. In North Queensland, Australia, a vast deposit of pitchstone is mined and processed for expandable perlite aggregate. During the classification stage of the excavated natural material, waste pitchstone fines (PF) less than 0.5 mm in size are generated. This study evaluates the waste PF as a viable, eco-friendly pozzolan for the partial replacement of PC. The reactivity of the PF is compared to fly ash (FA), using the pozzolanic compressive strength activity index (SAI) after seven, 28, and 91 days ageing at 20 per cent and 40 per cent PC substitutions. PF was found to be comparable to FA as a pozzolan at 20 per cent PC substitution at all ages tested. However, for the 40 per cent substitution blends significant strength was only achieved at 91 days ageing for the FA blend. The pozzolanic reactivity was also investigated using thermogravimetric analysis to determine the degree of free lime present after 91 days. In all cases where an SCM was added, the free lime was observed to be consumed with increasing age.

Jan 1, 2008

By S Arnold

Properties of the soil profile fundamentally control water-limited ecosystems. Soil water availability affects vegetation dynamics of plant communities, but is also affected by these communities in return. Understanding this eco-hydrological interplay and the role of physical soil restoration is crucial for successful rehabilitation and management of post-mining landscapes in semi-arid areas. However, uncertainties exist in both the mathematical description of plant communities within ecological submodels and the predictability of future rainfall events. This study uses information gap decision theory combined with an ecohydrological system model to investigate how both uncertainties impact decision-making in the context of ecosystem rehabilitation. A range of management strategies are investigated to identify the optimal soil thickness for successful rehabilitation of native plant communities in Central Queensland. The results emphasise that thicker soils can counterbalance uncertainty in mathematical description of plant communities by increasing the simulated survival probability of plant communities. However, the influence of thicker soils on the robustness of plant communities against a change in future rainfall amount is rather marginal. By allocating an economic value for restoring a particular thickness of soil layer, these results can be used to evaluate the costs of ecosystem re-establishment with regard to two target measures - the survival probability of the plant community and their robustness against climate change.CITATION:Arnold, S, 2012. Finding optimal soil restoration strategies in the face of uncertain future rainfall amount, in Proceedings Life-of-Mine 2012 , pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By T Krull, T J. Donohue, D Ilic

"Problematic issues in materials handling applications are often amplified in the iron ore industry due to the relatively high density of the ore as well as the abrasive nature of the product. One of the main issues arising from the handling of iron ore is excessive wear, with two applications typically suffering accelerated wear issues being transfer chutes and conveyor belts. These wear issues are problematic due to additional capital costs, but mainly due to the associated downtimes resulting in the accelerated wear. This study will focus on the modelling of iron ore in practical applications where design work was undertaken in order to reduce the wear rates of different materials handling equipment.CITATION:Donohue, T J, Ilic, D and Krull, T, 2013. Modelling of iron ore in materials handling applications with a focus on wear, in Proceedings Iron Ore 2013, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995