Search Documents

By Sydney H. Loram

TEIS paper, which is merely an arrangement of data collected during several hurried journeys, is offered to serve as a record, until such time as a better substitute be compiled. My observations were confined, as far as possible, over the entire distance, to the actual river valley; because near the Central Cordillera the country is so mountainous as to be im; passable in any direction but that of the dominant valleys. The river is not navigable anywhere, and for the first part of its course is a mountain torrent that runs down the bottom of narrow, almost vertical-sided valleys, through which the only road requires repeated fording, and often following up the bed of the stream ; but the rock-walls, standing clean and free from debris on either side, present the different formations with remarkable distinctness. A topographical map and a cross-seetion of the Rio Huasco is given in Fig. 1. The Rio Huasco practically rises from Laguna Grande, a lake about 17 km. from the Argentine boundary, and 3,135 m. above se-level, which is fed by direct snow-water, and by a few streams varying from a considerable volume, when supplied by the melting snow, in late spring, to little or nothing during the rest of the year. It is a somewhat pear-shaped body of water, about 1.5 miles in length and half a mile in average width, with a reported maximum depth of 45 meters. It was formed by the choking up of a narrow continuation of the same valley with blocks of an agglomerate mentioned later. The present level is some 5 m. below high-water mark (to which point, according to local accounts, it has not been filled for 35 years). In the intervening margin is a calcareous deposit about 4 m. thick, formed by the rapid evaporation of the water in the exceedingly dry air, and aided by the capillary action of an aquatic plant, growing in thick masses around the edge of the lake. These masses, dying and banking up, form

Jan 1, 1905

By D. Harrington

ONE of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out' of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. Dr. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo., their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and Dr. R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to cooperate.

Jan 2, 1921

Safety and health are no longer secondary responsibilities but must be of paramount concern to every mining operation, according to Anthony J. Thompson, an attorney with Hamel, Park, McCabe & Saunders of Washington D.C. The Mine Safety and Health Administration (MSHA) forecasts an estimated 19,000 inspections during 1979, and the economic and psychological impact of these inspections may he significant. To illustrate his point Thompson reviewed the experiences of a relatively large operation during a recent MSHA visit. The inspector was on the premises for two months, issuing between 250 to 300 "significant and substantial" (s&s) citations. During the most intensive period, about one month in duration, the operation experienced a production loss estimated between 2500 to 3000 tons; an accident rate up 30% over the previous month and 20% over the same month in the preceding year; 100% of the safety director's and safety engi¬neer's time was devoted to the inspection; 50% of top level management's time; and 90% of the mid-level or front line supervisory's time.

Jan 11, 1979

By Raymond L. Orr

Calorimetric measurements have been made of the heats of solution of gold axd indium in a number of liquid tin-rich alloys at a temperature of 705°K. Relative partial molar enthalpies of gold were determined as a function of dilute solute concentrations in the binary Au-Sn system and in the ternary Ag-Au-Sn and Au-In-Sn systems. Relative partial molar enthalpies of indium were determined for dilute solute concentrations in the In-Sn, Ag-In-Sn, and Au-In-Sn systems. Through application of the interaction coefficient concept introduced by Wagner and more recently extended by Lupis and Elliott, ualues have been obtained for the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. The results are inte@reted in terms of solute atom distributions through comparisons with the predictions of dilute solution models. INTEREST in the thermodynamic behavior of dilute liquid alloys stems from two primary sources. From a practical viewpoint, it is often of importance to know or to be able to predict the effect that one solute will have on the thermodynamic properties of the other solutes in a multicomponent system. Studies of dilute solutions may also be rewarding from the theoretical point of view. Some of the difficulties arising from the more complex interactions possible in concentrated solutions are avoided, leading to easier interpretations in terms of solutibn models and bonding energies. For example, in a binary alloy the limiting values of the partial molar properties of the solute represent the case for which each solute atom is completely surrounded by atoms of the solvent, and no other interactions are possible. Solute - solute interactions in dilute solutions are conveniently treated by the interaction coefficient concept of ~agner.' Using a Taylor series expansion for the logarithm of the activity coefficient, In yi, of a component, i, in a solution consisting of dilute solutes with atomic fractions xi, xj, xk, and so forth, in a solvent, s, and neglecting the second- and higher-order terms, Wagner obtained the expression: Where Wheyz is the limiting value of yi in the pure solvent, s. The interaction coefficients, e:, e:, and so forth, are defined by: Since yi is related to the excess partial molar Gibbs energy of component i by GfS = RT In yi, E: is re- ferred to as the "Gibbs energy interaction coefficient". Lupis and Elliott~ extended Wagner's treatment to the relative partial molar enthalpy, aHi, and the excess partial molar entropy, qS. They defined the enthalpy interaction coefficient as: and the excess entropy interaction coefficient as: leading to expressions similar to Eq. [I]: The three interaction coefficients are related by? The self-interaction coefficients, E:,qf,and at, represent the effects of interactions between atoms of component i in solvent s; €3, q{, and 03 represent the effects of interactions between i and j atoms in solvent s; and so forth. From the Maxwell-type relationships between partial molar quantities, it may be shown1'2 that e{ = ej, r}\ =tj), and ai - crj. Experimental determination of the interaction coefficients requires extremely precise measurements of the appropriate properties as functions of solute concentrations in very dilute regions. Few such data exist for intermetallic alloys, even for binary systems, because of experimental difficulties. This is especially true with respect to enthalpy data for dilute alloys. Examination of the compilation of data for binary alloys by Hultgren, Orr, Anderson, and ~elle~~ reveals that determination of limiting values of &fii(Xi =0) often requires extrapolations to infinite dilution from xi = 0.05 to 0.10. Direct measurements of the enthalpy interaction coefficient, qi, for multicomponent systems are virtually nonexistent. This quantity is of course subject to direct calorimetric measurement, but its determination must be limited to cases where high experimental precision is possible. The heats of solution of gold and indium in liquid tin can be measured with relatively high precision, which makes determinations of 73 involving these metals as the measured solutes experimentally attractive. This paper presents the results of such determinations of the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. MODELS FOR DILUTE-SOLUTION BEHAVIOR Random-Solution Behavior. In the quasi-chemical treatment of solutions, only nearest-neighbor bonds are considered, and a composition independent value

Jan 1, 1967

By C. G. Dunn, F. Lionetti

W. G. BURGERS*—It seems almost certain that this investigation shows the way which finally, when more analogous data have been obtained, must lead to the understanding of many features of preferential growth-directions of crystals and of the occurrence of recrystallization textures. In this connection I should like to mention that Mr. Tiedema in my laboratory succeeded in developing an analogous method for preparing crystals in aluminum plates with a chosen crystal-lographic plane and direction parallel to the surface of the plate (to be published in Cryst. Ada). If such crystals were grown in high purity aluminum and test-pieces containing a few crystals such as the authors describe were prepared for this metal, it might be possible that due to the absence of growth obstructing particles, even in this low-melting point metal boundary displacements approaching equilibrium positions might be realized. With regard to the apparently marked drop in surface energy for orientation differences approaching zero degree, and orientation differences approaching those existing between twins, it seems of interest to remark that in aluminum a crystal growing at the expense of fine grained material cannot (or can only very reluctantly) absorb grains in either ap- proximately (within 5—10°) parallel or spinel twin orientation (May, Tiedema and Burgers, Nature (1948) 162, 740 and Cryst. Ada in press). Consequently with aluminum the method of preparing a crystal with a definite orientation does not succeed when the new crystal has to absorb its own texture; for example it is not possible to grow in a polycrystalline wire with a [lll]-texture a crystal with a [11 Indirection parallel to the wire axis (Tiedema: Cryst. Ada, in press). Finally I should like to mention the well-known fact (Burgers: Proc. Acad. Amsterdam (1947) 50, 723) that prolonged annealing of recrystallized nickel-iron sheet with cube-texture never succeeds in transforming this into one single crystal of the same orientation; if, by "secondary re-crystallization," large crystals are formed

Jan 1, 1950

By A. Ojanen, T-L. Huggare, A. Kuivala

An electrolytic zinc plant with a capacity of 90,000 tons/year went on stream in Kokkola, Finland, in late 1969. It is a standard electrolytic zinc process plant; however, it has been subjected to several process improvements and enlargements during its time of operation. A fluidized bed roaster treats 500 tons/day of zinc concentrates which also contain mercury. Since the mercury evaporates completely in the roasting process, a mercury removal unit has been added to prevent, contamination of sulphuric acid produced in the neighbouring acid plant. The same unit also removes selenium from the roaster gases. In a separate unit, about 6 tons a year of metallic 99.999% mercury is recovered. The neutral leaching, originally a batch process, has been converted to a continuous operation, and a residue treatment system comprising hot acid leaching and jarosite precipitation has been added. Purification comprises a "hot arsenic-zinc dust" step and a cadmium removal step with zinc dust, both operated batchwise. Purification residues are used to make about 200 tons/ year of 99.99570 cadmium in a process developed by Outokumpu Oy. The electrolytic precipitation of zinc carried out at medium current density gives zinc of 99. 995% purity.

Jan 1, 1973

By Bernard MacDonald

The writing of this paper was prompted by the discussion by H. M. Chance of the paper written by Thomas M. Chance,l and by the remarks of the editor in which he stated that while the matter contained in discussion did not refer to the original paper it " was presented as of interest to the operators of cyanide and other lixiviation processes dealing with fluid mixtures of varying specific gravity." For some years past the principle enunciated in the discussion referred to has been known to the writer and demonstrated by him to be an efficient and economical way of separating water or solution from solids in the cyanidation, lixiviation or acid leaching of ore pulps. In utilizing this principle in commercial practice he has invented a method whereby not only the separation of solution from solids may be effected in any given tank, but also the counter migration of the solids and solution may be effected continuously through a series of tanks in which the hydro-metallurgical treatment of ore pulps is being carried on. In effect this method is analogous to the counter-current system, but is different physically in that it is carried on throughout a series of tanks on practically the same level, continuously and automatically, by hydrostatic pressure and gravity-flow, without the aid of intervening pumps or elevators, at the same time that agitation is being carried on in the same tanks. In the Parral system, agitation is effected in tanks by a number of air lifts of comparatively small diameter through which the pulp is continuously transferred from the bottom of the tank and spouted horizontally on top of the charge. The spouting force of the several streams thus discharged maintains a rotary flow in the pulp charge which extends from top to bottom of the tank. This continuous transfer of pulp and the spiral flow from top to bottom of the tank maintains the pulp constituents in uniform proportions and meets the requirements of efficient treatment in a most economical manner. The quantity of compressed air required is very small, as the pulp is not lifted but simply transferred from the bottom to the top of the tank charge under hydrostatic balance. Fig. 1 gives a bird's-eye view of two adjoining tanks in any series equipped with the apparatus for producing the separation of

Jan 1, 1919

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam's path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By A. S. Grove, C. T. Sah, E. H. Snow, B. E. Deal

A summary of- several recent investigations in to the properties of the metal-oxide-silicon system is presented. A major portion of these studies makes use of the MOS capacitance-z)oltage method of' analysis. The particular areas of investigation which are reported include: 1) a general survey of the electvical properties of thermally oxidized silicon surjbccs; 2) a study of ion migration through silicon dioxide films ; 3) measurements of electron and hole mobilities in surface inversion layers; 4) a study of impurity redistribution due to thermal o.ridatiotz; and 5) measurements of the rates of oxidation oj-heavily doper7. silicon. THE importance of the metal-oxide-semiconductor (MOS) system in the semiconductor industry is well-known. In addition to its importance in the "planar" device technology,' the MOS structure is now also used in the fabrication of active solid-state devices. Consequently, extensive efforts have been made recently to obtain a better understanding of the characteristics of this system. A summary of some studies of the MOS system conducted in our laboratories during the past year is presented. For the most part these studies used silicon as the semiconductor, along with silicon dioxide and aluminum as the other two components of the system. Since the MOS capacitance-voltage method of analysis was used extensively in these studies, we will first briefly describe its nature and consider some of the possible causes of deviation of experimental observations from the simple theory. We will then outline the various related areas of investigation carried out in our laboratories and will briefly indicate some of the results. It should be noted that the purpose of this paper is merely to provide a brief summary of MOS studies. More detailed discussions of the various areas of investigation are given in the references cited. PRINCIPLES OF THE MOS C-V METHOD OF ANALYSIS' A sketch of the MOS structure is shown in the upper portion of Fig. 1. In this case the insulating film is Si02 and the semiconductor p-type silicon. If a large negative bias is applied to the metal field plate, holes are attracted to the silicon surface. The silicon then behaves much like a metal and the capacitance measured is that of the oxide layer alone, Co. If a small positive bias is applied to the aluminum, holes are repelled and a region depleted of majority carriers is formed at the silicon surface. This depletion I-egion adds to the width of the dielectric and the measured capacitance begins to drop. With increasing positive bias, the width of the electrical depletion region increases. At some large positive bias an inzevsion regiotr is formed at the surface and additional charges induced in the silicon appear in the form of electrons in this narrow inversion region. Thus the depletion-region width approaches a maximum value and, consequently, the capacitance reaches a minimum value and then either levels off or rises again depending on the measurement frequency and the rate of equilibration of the minority carriers in the inversion layer.3 Band diagrams, along with the corresponding charge distributions, are shown in Fig. 1 for the above bias conditions. If minority carriers cannot accumulate at the surface to form an inversion region, the depletion-region width continues to increase with increased positive bias and the capacitance drops toward zero as in a reverse biased p-n junction. The effect of a work-function difference $hs between the metal and the silicon, and of surface charges per unit area Qss located at the oxide-silicon interface, is simply to attract charges in the silicon much like the applied bias. It can be shown that this results in a parallel shift of the capacitance-voltage characteristic along the voltage axis by an amount corresponding to AV = -$bIs + Qss/Co. Theoretical curves have been calculated4 giving the capacitance of the MOS structure C normalized to the oxide capacitance Co vs the quantity VG here VG is the voltage applied to the metal field plate. In Fig. 2 such calculations are shown as points for a particular oxide thickness and bulk impurity concentration for a p-type semiconductor. (For an n-type semiconductor the curves would be mirror images of these.) All three cases, i.e., low frequency. high frequency, and depletion, are indicated. Also shown in the figure are recorder tracings of the characteristics of actual devices. These characteristics have been shifted along the voltage axis to compensate the effect of surface charges and work-function difference. It is evident that agreement between experiment and theory is good. The nature of this shift along the voltage axis is

Jan 1, 1965

Phase II of President Nixon's economic game plan will incorporate many top flight metals mining companies. The large corporations must receive approval from the Cost of Living Council before increasing prices and or wages. The theory here is that, with large companies complying with advance approval, smaller firms will be examined more closely by government, and thus will be forced also to comply. Rep. Paul McCloskey (R.-Calif.) called for a moratorium on strip mining for "the few years involved before we adopt a national energy policy and a national land use policy." McCloskey, who is a cosponsor of Congressional legislation that would outlaw strip mining, told a hearing that a "moratorium can scarcely hurt us until national energy and land use policies are adopted."

Jan 1, 1971

By Alan Morris

THE investigation of the hot-working properties of metals and alloys furnishes a problem which has been attacked in many ways. Tensile, impact and hardness tests on heated specimens have furnished interesting data, but in most cases either the tests are difficult to make or the results hard to translate into terms of practical value. Some investigators have used the drop hammer to advantage. It furnishes a rapid and simple method of comparing the plasticity of metals at elevated temperatures. The indications obtained by its use are of value only in so far as their significance is understood and they can be intelligently used to predict the behavior of a given metal under given hot-working conditions. The work reported here was undertaken not only to add-something to the existing volume of such data but also to contribute to our understanding of the results. Doerinckel and Trockels1 used cylindrical specimens and determined the work required to reduce the specimen to one-half the original height. Ellis2 studied the effect of constitution on the malleability of steel at high temperature. His method and that of Kent3 were similar to the one used in the present work. The tests described by Kent were made on samples of tin, zinc, aluminum, copper, lead, 70:30 and 60:40 brasses, with and without a small quantity of lead. He concluded that the test would "indicate whether a material can be forged at a given temperature without cracking." This interpretation must be used with caution. While it is probably true within limits, one must consider the severity of the forging operation. Again, it will not apply strictly to forms of hot working other than forging. For instance, an alloy running 61.0 per cent. copper, 3.25 per cent. lead, remainder zinc, will crack badly in the test, yet it is extruded commercially. When the possibility of hot-working a new alloy is being considered a study of its drop-hammer test should help

Jan 1, 1931

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

By H. W. Turner

Lying to the east of the Rio Grande, in central New Mexico, is a long N. and S. mountain range, broken into separate ridges at several points. These have received separate names; the mountains at the south end, near El Paso, being known as the Franklin mountains, and then, following successively, to the north, the San Andreas range, Sierra Oscura, Manzano and Sandia mountains. At the eastern base of the Sierra Oscura there are several low ridges, remarkable for their red color. All of these red ridges contain reefs of copper-ore. The eastern flanks of the Sierra Oscura are composed of limestone. Some fossils in the limestone were examined by Prof. J. P. Smith of Stanford University, who says they are Fusulina and indicate an Tipper Carboniferous age. The sandstones and shales containing the copper-reefs directly overlie this limestone (Fig. I), and are very likely of Permian age, like the similar beds in Texas, described by Mr. W. F. Cummins.* Overlying the copper-beds are red sandstones and shales in which very little copper has been found. The cupriferous zone and the red sandstones and shales are everywhere associated, and as one stands on a high point, he will see that these rocks form three main belts or lines of hills. These may be referred to as the northern, middle and southern belts. The northern belt was not visited by me, but is known to contain copper-deposits. The middle belt has a trend of N. of W. and S. of E. The copper-reefs have been traced for a distance of more than 2 miles. The southern belt has a trend of about N. 30' W. and S. 30°

Jan 1, 1903

By F. N. Kissell, W. E. Schroeder, N. I. Jayaraman

This article discusses methods of improving airborne capture by conventional dust suppression systems. The work was performed in a full-scale plywood model of a mine entry with a wooden mockup of a Joy 12 CM continuous miner. Dust was introduced at the front of the entry, and water sprays knocked down part of the dust cloud. Sampling in the return air determined the percentage dust reduction. Based on the results, guidelines are offered for continuous miner spray systems to control dust. Empirical relations have been developed to determine the effect of changes in water spray pressure on air movement, dust knockdown, and pollutant concentrations in the face return. Nozzle selection and arrangement are discussed for high dust knockdown efficiencies.

Jan 1, 1986

(Members are urged to send in for this column any notes of interest; concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Nov. .10, 19 16 to Dec. 1.0, 1916: Chester Atkinson, La Fundicion, Peru. , Paul Llewellyn, East Chicago, Ind. F. J. Brule, Toronto, Ont., Canada. Harry March, London, England. Sterling H. Bunnell, New York, N. Y. E. P. Mathewson, Toronto, Ont., Canada. G. H. Cunningham, Hobart, Tasmania.' E. W. Moore, Budapest, Rumania. Courtenay DeKalb, Tucson, Ariz. W. J. Pentland, Guadalajara, Mex., E. H. Dickenson, New Y.. Heinrich Ries, Ithaca, N. Y. E. B. Durham, Mount Kisco, N. Y. W. E. Saunders, Philadelphia, Pa. L. B. Eames, Pueblo. Colo. J. G. Scrugham, Reno, Nev. N: H. Emmons, 2d, Copperhill, Tens. - W. H, Seagrave, Kennecott, .Alaska. R. E. Hoffman, Hannibal Mo.'s H. B. Small, Magangue, Colombia. B. B. Hood, Chronic, N. J. W. H. Staver, Washington, D. C. H. E. Jackman, Rochester, N. Y. R. K. Stockwell, Santiago, Chile. F. H. Jackson, Joplin, Mo. Warren D. Thompson, Boston, Mass. Knight S. Jordan, Provo. Utah. Thor Warner, Kingman, Ariz. William Kelly, Vulcan, Mich. S. T. Wellman, Cleveland, Ohio. W. H. Lanagan, San Francisco. Cal. F. H. Willcox, Pittsburgh, Pa. H. H. Lauer, Northampton, Pa. Arthur K. Adams has been appointed geologist to the Andes Copper Co.

Jan 1, 1917

By J. D. Price, W. M. Bertholf

A. C. RICHARDSON*—First of all, [ think that the paper represents a lot more work, study, and correlation than has been indicated by the brief talk by Mr. Price. I like the way he started out and described the areas from which the samples were obtained, the locations of the washing plants, the available tonnages, and other background information with which to evaluate the data he submitted later on. Then I like the way in which he described the various types of washing plants, the tonnages handled and the difficulties of the washing problems; showing the amount of material that lies close to the specific gravity at which the washing separation is made. Later he gave figures from washing plant operations showing recoveries and cleaning efficiencies. He then discussed his own plant at Pueblo. It is the same old plant, I think, that I worked around a good many years ago. It is unusual to find a plant treating nearly 5000 tons of coal a day on tables. But this table plant is, I believe, more efficient than is indicated by the figures that Mr. Price gave. To determine the efficiency of a cleaning operation or to compare it with another it is necessary to consider the quantity and character of the material close to the specific gravity at which the separation is made. It is not fair, I believe, to penalize the table operation by something like 4 pct of out-of-place-material as he has done here. The variety and difficulty of the coals that he has to wash, the continuous shift and change in their composition make a very difficult cleaning problem and the table performance is excellent. I believe that the information in this paper will be of interest and value to anyone operating or planning to build a coal cleaning plant in this or other areas; particularly where the cleaning of fine coal is a problem. The data may be used for comparative purposes in determining the relative efficiencies of other cleaning plant separations. E. D. HAIGLER*—What is a Baum jig? J. D. PRICE (authors' reply)—A Baum-type jig is one in which the pulsations of the water is secured by means of a pulsating air current applied on top of the water. I imagine you are all familiar with the old plunger-type jig which is in effect a U tube in which a plunger on one side of the U, moving up and down, causes a corresponding pulsation on the far side of the jig. In the Baum jig, the pulsating air current is applied on the surface of the water on one side of the U tube of the jig and gives a corresponding pulsation on the other. It is also commonly known as a pneumatic jig. The control of the rise and fall of the water in the jig body proper is under much better control than it is in any of the other type jigs. Mr. Richardson could enlarge on that feature, for I know that he has had considerable experience with these jigs. A. C. RICHARDSON—You have asked how to control a Baum-type jig. The pulsations in a Baum jig can be modified and regulated to a marked degree by the amount of water admitted to the jig and by the adjustments of the valve which regulates the manner in which air is admitted. The number of pulsations per minute is controlled by the number of cycles of the air valve. Thirty to forty cycles per minute is a good speed for large jigs treating coarse sizes of cod. With an air valve it is possible to modify the time-velocity curve of the pulsating water to some extent which in turn determines the action in a jig bed. Within limits the following parts of the air valve cycle may be regulated: (1) the rate and period of air admission, (2) the period of air expansion, (3) the rate and period of air exhaust, and (4) the period of air compression. The rate and period of air admission determines the acceleration of the water at the beginning of the pulsion stroke and the amplitude of the stroke. The period of air expansion, after inlet port is closed, is one in which the water has reached the desired velocity, positive acceleration reduced, and the bed held in a mobile condition. The rate and period of the air exhaust can be adjusted to modify the degree of suction and so modify the manner in which the particles in the bed stratify. The compression period, alter the exhaust port closes and before the intake port opens may be used to advantage in retarding the downward velocity of water during the suction stroke. An ideal jig stroke is one in which during the up stroke the bed is lifted slowly in a mass and opens up like an accordian with the bottom layers dropping away first. With the bed open and mobile the particles adjust themselves according to their hindered settling rates. During the down stroke, while the bed is still open the particles of high specific gravity are accelerated toward the bottom layers. It is possible to approach this stroke with all types of jigs but it is less difficult to approximate it with a Baum jig.

Jan 1, 1950

By Marcel R. Daly

EUGENE COSTS, Calgary, Alberta (communication to the Secretary*).¬This new theory to account for the accumulation of commercial deposits of oil and gas, is deliberately and admittedly based on the hypothesis that the origin of these products is organic. Mr. Daly says (page 1142), "Should the organic origin of the petroleum that is found in pools be granted, the following interpretation is offered for the mechanics of its accumulation." But suppose the origin thus accepted by definition be incorrect, then what becomes of the diastrophic theory, Mr. Daly's interpretation? As Mr. Daly remarks himself (same page), "It is obvious that the history of petroleum will have to be entirely different, dependent upon its origin, either from emanations coming from the depths, or from organic decomposition in the strata themselves." Then why should one propound a theory, through which he is endeavoring to trace the history of petroleum, by starting with a definition of its origin? The origin should be the deduction, the forced conclusion of the theory, and not its starting point. Facts alone should be considered first, in any theory worth the name, until sufficient proofs have accumulated to permit of the deduction of a complete explanation for these facts. This would lead one to the origin through a real theory founded on facts, and not based on a preconceived idea perhaps true, but possibly fanciful. Mr. Daly's way can only lead on one road, namely the organic road, and, I repeat, it may be the wrong road. In the case of the petroleum deposits, as .I have endeavored to show in several papers on the subject, to which the reader may refer, the facts clearly lead to the force conclusion that their origin is not one of accumulations of hydrocarbons at first disseminated in the sedimentary strata but the reverse process of subsequent local infiltrations and impregnations of hydrocarbon emanations from the depths. This new theory, therefore, founded on, an erroneous conception of origin cannot be a help in the solution of the petroleum' problem, not any more than were the anti-theory or the hydraulic theory, both of which were also based on the same error, although Mr. Daly is inclined to think that the authors of these two theories did not accept the misconception boldly enough (page 1142). -

Jan 12, 1916

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By H. S. Ten Eyck

Fertilizer normally is spoken of as having three main components: nitrogen, phosphorus and pot- ash. Certainly, however sulfur must also be considered a basic component of fertilizers, even though in many instances it does not end up as a part of the end product. In addition, with heavier cropping and the resultant drain of plant foods from the soil, we have now reached a point where the minor elements necessary for plant growth have become a major factor in the fertilizer industry.

Jan 7, 1967

NEW YORK SECTION Executive Committee DAVID H. BROWN, Chairman JOHN H. JANEWAY, Vice-Chairman F E. PIERCE, Secretary, 35 Nassau St., New. York, N. Y. P. A. MOSMAN, Treasurer LEWIS W. FRANCIS BENJAMIN B. LAWRENCE At the meeting of the New York Section held at the Machinery Club on Dec. 8. 1915, the subject was "The Engineer in Modern Warfare, with Especial Reference to the Present European Conflict." Dr. Henry S. Drinker, who is Chairman of the Institute committee on the Engineer's Reserve Corps movement, opened the evenings' talk with a short statement of the aims and advantages of the Students' summer military camps, fostered by the Society of the National Reserve Corps, he being a member of the Advisory Committee of University Presidents. The speakers of the evening were Col. William M. Black and Col. John Biddle, both of the Corps of Engineers, U. S. Army. Col. Black is the

Jan 1, 1916