Search Documents

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By C. E. Golson

The preparation of aggregates is a form of mineral processing which has been taken for granted for many years, mostly because of its lack of glamour when compared to the winning of metallic minerals from their ores. Many of the processes and equipment now used in the metallic mineral processing industries originated in the more prosaic preparation of aggregates. 'Their adaptation to metallurgical processes has led to developments both in their design, and in their use. Modern practice, has been so exacting in its demands that, in many cases, this improved technology is finding new applications in the very industry in which it originated the mineral aggregate industry, The low cost requirements, large tonnage capacities and complex specifications which govern the acceptability of its products have node modern aggregate processing a much different art than it was one or two generations ago. The basic conditions which govern the type and quality of mineral aggregates were presented in an addendum to a paper given at the San Francisco Meeting in 1959 by one of the authors.

Jan 1, 1961

By D. Robert Weir, M. J. H. Ruscoe, R. M. Berezowsky, M. A. Clegg

The metallurgical processing involved in the produc-tion of the new Canadian one dollar coin is reviewed starting with the hydrometallurgical production of pure nickel powder, followed by the powder metallurgy process for the production of nickel strip and coinage blanks, and concluding with the Aureate bronze electroplating and heat treatment procedure. Coinage requirements are then reviewed with regard to economic, public acceptance, and service requirements. Finally the properties of Aureate nickel coinage are presented in the light of the many and varied coinage requirements, and it is concluded that the new Canadian dollar coin exceeds the requirements admirably.

Jan 1, 1990

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written which aid in the design process in the academic arena and should also have industrial applications. The programs described include a dragline cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program and an overburden volume and coal tonnage sequencing program.

Jan 1, 1985

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By Francis Lucas

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or-under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black, oxide that cannot be absorbed by the metal.

Jan 1, 1927

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By W B. Edgar, I M. Platten, C A. J Towsey, B W. Cuffley

The evaluation of historical goldfields has been common over the past 15 years, reflecting changing economic conditions, improvements in knowledge and technology and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins, which are structurally complex with an irregular distribution of gold, have variable geometry and architecture and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation, since it contributes to understanding the orebody, exploration target size and setting expectations. Mine records include documents such as plans, sections, reports, news cuttings, production tabulations, etc. A major advantage for the modern explorer is the capability of computer modelling to display this data in 3D. Historical records can give the explorer substantial information on various deposit characteristics, not least grade and geological continuity, geometry and architecture, mineralogy, metallurgical properties, bulk density and ground conditions. From an evaluation perspective, historical records can be used to support a Mineral Resource estimate, though its application will depend upon the quality and quantity of the data and judgement of the Competent Person. Effectively used, historical records can reduce geological uncertainty and focus evaluation efforts û thus reducing project risk.

Jan 1, 2009

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By Gunther F. Leichtle, James A. Finch, Colin A. Hardie, Cesar O. Gomez

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibers for use in newsprint. The mineral processing group at McGill University in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network) has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University's flotation column test work at a Quebec wastepaper recycling facility.IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world's largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and U.S. municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World's solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity.A key to the success of producing quality recycled fibers from wastepaper is the deinking technology. The production of tissue papers, paper towels and newsprint requires regenerated fibers which are substantially free of ink particles. Of the various options available, mineral processing techniques can offer the most economical, environmentally acceptable and versatile strategies (Yoon, 1993). Today, it is recognized that flotation is one of the most effective processes for removing ink particles in the production of a high quality product. In a collaborative program with the Pulp and Paper industry, the mineral processing group at McGill University has adapted column flotation technology for this purpose. This article will describe the typical process of deinking from a mineral processing point of view (Part A). It will also present some results from McGill University's flotation column test work at a nearby paper recycling facility (Part 8)."

Jan 1, 1998

By Juan L. Yarmuch, Gonzalo Sepulveda

This article presents a novel approach to address the mining width-constrained open pit mine production scheduling problem in the context of medium-term planning. A mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the NPV of the schedule while ensuring enough room for the operation of mining equipment. To tackle the computational challenges posed by large-scale instances of the problem, we propose a method based on variable fixing and horizontal precedence generation. In this study, we apply the developed model to real-world scenarios from Radomiro Tomic short-term mine planning problems such as optimizing the timing of major truck maintenance and the impact of external factors, like the delay in the production of the Chuquicamata underground project. Remarkable improvements are observed with the mining width-constrained model. Specifically, the mining width satisfiability is enhanced from 2 to 60% compared to the traditional open pit mine production scheduling model, underscoring the significance of incorporating these constraints. The proposed method showed good results reaching optimality gaps within 5%.

Mar 28, 2024

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By Javad Sattarvand, Frimpong Kwaku Asare

The safe evacuation of miners during an emergency in the shortest amount of time is one of the most essential features of a mining operation. Despite advancements in mine evacuation research, the usage of mine vehicles during evacuation has not been considered. The majority of recent studies have been done on miners’ evacuation on foot. Mathematical formulations including Minimum Cost Network Flow (MCNF) models, Dijkstra's algorithm, Floyd-Warshall algorithm, and Ant Colony Optimization models have been used to solve mine evacuation problems. These models, which concentrate on determining the shortest escape routes during the evacuation, have been found to be computationally expensive and may not offer the best solutions in some cases. The goal of this paper is to incorporate light vehicles in the evacuation process using a mixed-integer programming approach. The methodology aims to minimize the total time required to evacuate the mine, ensuring minimal exposure of the miners to the adverse conditions that triggered the evacuation.

Jun 25, 2023

By D. Grosse

At the beginning of the 1960's, the Hannoversche Portland-Cementfabrik A. G. needed to open a new quarry. The land on which this quarry was to be developed was completely flat and separated from the existing quarry by a navigable canal. The area had been exploration-drilled previously, so that enough reliable data on the chemical properties of the deposit were available. From the geologic point of view, the deposit under a very moist surface belongs to the Turon (Upper Chalk) formation, soft on the surface and medium to very hard farther down. Between the 15% sloping banks of chalk (with a calcium carbonate content of 75 to 90% and running from west to east), there are numerous beds, up to 3 m deep, which are rich in alumina and iron oxide but contain only 50 to 60% CaCO3. In the old quarry-worked conventionally by deep-hole drilling, a 2-cu-m shovel, and 900-mm track with 6-cu-m dump cars-an adequate and modern crushing plant was available. The plant crushed the moist material (11 to 13% H2O content) down to 0 to 50 mm. INSTALLATION OF ORIGINAL MOBILE CRUSHER It was decided to employ a mobile crushing unit in the new quarry; the moist and soft ground did not permit the use of heavy trucks for transporting the material, and a road network would have entailed a large investment. The use of a rail system was eliminated from the beginning, since the ground would be very uneven after the quarry was developed. At that time only one prototype of a crawler-mounted mobile crushing unit existed. This unit was operating in a nearby works as a primary crusher. A similar, slightly improved machine (Fig. 1) was purchased

Jan 1, 1969

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By D J. Black

Ventilation modelling is used to evaluate ventilation system performance. This paper describes modelling to assess potential changes to a single entry longwall ventilation circuit to improve ventilation and gas management. The longwall panel is extracting a 215 metre face in a 1.5 metre coal seam at a depth of 900 to 1000 metres below surface. The 1.5 metre B seam is located approximately 25 metres below the main 3.0 metre A seam and the gas content of both coal seams is approximately 20 to 25 m3/t. The B seam is extracted prior to the A seam and the mine relies on fracturing of the overlying strata to induce gas emission from the A seam to reduce the gas content prior to mining. Longwall operations in the B seam are constrained by limited ventilation and high gas emissions. Due in part to statutory limits on gas concentration and air velocity, the average longwall production rate is approximately 700 t per day.Gate roads in the B seam are single entry, developed using road headers and supported with steel arches. Additional timber cog support is installed to reduce roadway closure from abutment loading. Due to the slow advance of gate road development, mine management were reluctant to consider significant mine design changes, such as two heading gate roads; therefore, the investigation focused on determining the extent to which ventilation and gas emission impacted on longwall production performance, while recommending short-term, low-cost actions to improve ventilation and gas management to support increased longwall production.CITATION:Black, D J, 2017. Application of modelling to improve ventilation and gas management in a single-entry longwall panel, in Proceedings Australian Mine Vent Conference 2017, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017