Search Documents

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By A. M. Wala

It is common practice in Appalachia, when extending the life of an existing mine, to acquire the adjacent reserves and extend the existing mine into it. Also, often the existing mine is renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may be modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (M.V.S.) that require proper planning and control procedures. The authors describe and present the study that was carried out for the ventilation system of a newly expanded underground coal mine located in the Appalachian coal region. Discussed first is the process of correcting the ventilation system of the existing mine. Then, some of the stages of controlling the expanded system are discussed. Finally, numerical data for these steps are presented.

Jan 1, 1992

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By John Fred Rivera

Since its inception during the hectic days of World War II, Kaiser Steel Corporation has developed and maintained a solid reputation as a progressive company with an incessant penchant for attempting innovative ideas to improve its stature in the American and world corporate framework. The very latest in technology is aptly demonstrated in the new Basic Oxygen Process recently placed into operation at Kaiser's huge Fontana Steel Mill. Daring ventures such as this and other developments on pollution control devices have propelled Kaiser Steel Corporation into the forefront as the largest steel producer in the western United States. Kaiser Steel's boldness and willingness to attempt new ideas and the very latest in technology is by no means limited to its steelmaking operation. It extends into every phase of Kaiser's corporate structure.

Jan 1, 1979

By Richard W. Brummett

Problems in new strip mine development is a subject that could require several days to cover adequately. Coupled with the fertile imagination of television writers, we could probably expand it into a series rivaling Gunsmoke in longevity with just as many shootouts at sundown. It would-of course-be subject to a high Neilson Rating. To bring the subject into perspective, we will limit the comments to a general discussion covering western strip coal developments. Stimulated by increased demand for low sulfur coal, surface mineable western coal operations began a shift into high gear approximately four years ago. Then came last year's "energy crisis" that increased the pressure on coal development not only in the west, but nationwide. Several eastern power plants having dual oil and coal burning facilities were directed to discontinue using oil. Also, a number of new south and southwestern power plants scheduled to burn natural gas or of I commenced an ordered conversion to other fuels, namely, coal. The involved utilities with reserve positions accelerated their planning while others began the search for long-term commitments from coal producing companies. In addition, announcements were made for proposed mine mouth coal gasification projects in New Mexico, Wyoming, and North Dakota.

Jan 1, 1974

By Wade W. Bristol

The Jerritt Canyon Joint Venture project is located about 80 km (50 miles) north of Elko, NV. It produces approximately 9.3 t/a (300,000 oz/year) of gold. The joint venture is 70% owned by Independence Mining and 30% by Meridian Gold. Independence Mining is the operator. The Jerritt Canyon Joint Venture started operations in 1980 by mining a series of open-pit mines. The discovery of deeper ores during early 1990s made it neccessary for the operation to mine a large portion of its annual production by underground mining methods. Underground production started in 1993 at the West Generator Mine. This was followed by the Murray Mine in late 1994. Two additional underground projects are being developed. Underground mining at Jerritt Canyon is scheduled to produce about 3.9 t (128,000 oz) in 1997.

Jan 1, 1997

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By John G. Hall

Everyone forms his own mental picture when the subject of copper is mentioned. To an architect, copper is a warm, enduring metal with a quiet beauty; to the historian, man's first metal; to the product engineer, the best electrical and thermal conductor of all commercial metals; to the investor, a volatile stock; to the speculator, the daily price quotation; to those in the mining industry, the challenge of producing copper for rising needs in the face of rising costs and lower grades of ore. At this meeting, we will look upon copper as a key raw material in industry, in national defense, in technology, in world trade, and as a principal commodity in the economies of several developing countries. As miners, and most of us here are miners, we are prone to view our role as suppliers of copper. We locate, mine, smelt and refine the metal. In the complexities of today's world, however, following a period of the longest domestic copper strike in history which caused critical world-wide shortages and widely fluctuating prices; it becomes necessary for all of us to concern ourselves with the whole spectrum of copper affairs -"from mine to consumer " But first we need to look at the miner's side of the picture -- capacity and production. We will examine these functions in terms of the whole world -- not simply the free world. Nature did not endow all regions of the earth equally, and copper in world trade has a way of ignoring political boundaries. Science and technology, as well, know no national boundaries. It is said that the "Engineering & Mining Journal" has as many readers in the Communist World as in the Free World. Nor is this a one-way street. We presently have available to us in the. U.S., cover-to-cover translations of many Communist World mining and metallurgical journals.

Jan 1, 1968

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By R. J. Smith

Tar sand deposits in Utah represent more than 25 billion barrels of in-place bitumen, 96% of the known U.S. reserves. The technological development of a hot water processing strategy for the Canadian tar sands and the commercial Production of synthetic crude oil from this natural resource suggest that similar success may be possible for the utilization of Utah tar sands to provide our country with a new domestic source of synthetic crude oil. In this regard an active research program to develop a hot water processing strategy for Utah tar sands has been sustained at the University of Utah for the past five years. The hot water process for Utah tar sands differs significantly from that used for Canadian, tar sands due to the inherent differences in the respective bitumen viscosities and the nature of the bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion. (8,9) Subsequent flotation of the digested tar sand is a subject of current attention and is considered in this contribution for the Asphalt Ridge tar sand deposit. Although contact angle measurements of pure Asphalt Ridge bitumen indicate moderate hydrophobicity, air bubble attachment to the bitumen concentrate taken from a 37 liter flotation cell is not possible. This surprising result suggests that the flotation separation is dependent on air bubble entrapment rather than on attachment due to surface hydrophobicity. The occlusion of air bubbles in the bitumen is apparent from visual examination of the concentrate, especially at lower temperatures. It seems that a bitumen bubble agglomerate forms in the impeller region of the flotation cell, the effective density of which is such to allow the agglomerate to float to the surface. A factorial design of the major operating variables in the flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77C recovery of 96.7 percent was realized at a grade of 61.0 percent bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate.

Jan 1, 1980

By Richard L. Ash

Less than optimum production in mining always results when poorly blasted material is provided at loading points. More often than not the cause is due to blasting founds that fail to fully control and utilize explosive energy. In many cases the problem exists because too few blasters understand how blastholes actually break rock and recognize that blasting is a three-dimensional process in designing their blasts. To better understand how blasts can be more effectively designed the two major rock breakage processes are described. In addition, the respective contributions of the borehole and detonation pressures are defined as are the specific roles of the several important blasting design variables. The concept of stiffness as an engineering principle and its significance in blasting design is introduced for explaining the breakup of rock. Basic guidelines for affecting control over fragmentation and side effects like over-break are offered.

Jan 1, 1975

By G. A. Gordon

For the purpose of examining a specific problem, it is important that we look at the context, to obtain an appreciation of the general area of which the particular problem forms a part. It is my task today to speak on a particular relationship between the nations of Canada and the United States of America. What is the background? Almost two hundred years ago we both belonged to a family of nations -- the British Empire. There was a serious family quarrel in 1776 and the United States left the family and set out to make its own independent way in the world. Canada, which was not as grown up as the united States, remained with the mother country, and in 1812 resisted a vigorous attempt by the United States to get it to leave home too. With the passing of the years the bitterness of that family quarrel has faded and, aside from occasional differences, we have been getting along very well ever since.

Jan 1, 1962

By William F. Hahn

It is a pleasure to speak to this group about special crusher installations which are in the bauxite and phosphate rock processing industries. The installations to be discussed demonstrate the variety of conditions, materials, and results desired which must be evaluated before a selection is made from the specialized crusher technology available today. Those of you who are closely involved with phosphate rock and phosphate products processing will find some of this information a bit interesting and perhaps alien to your own descriptions or every day references. It is given from a "crusher" manufacturer's viewpoint and therefore is infused With our flair and language. General features of six (6) different crushers will be shown in cross-section With slides and will be discussed in the same order.

Jan 1, 1978

By III Boxley

Most of us realize that our nation's roadways are under ever-increasing stresses, from higher traffic counts to increased tire pressures and their resulting loads. At a time when the interstate system as originally envisioned is completed, and the National Highway System is being drawn to replace it, it is appropriate that we examine design and construction methods for the next century. The stone industry shares a common desire to produce high quality, cost-effective roadways that perform over time. The superior sub-grade and road base structure provides for the superior roadway. Since I am neither an engineer nor a contractor, I will not attempt to suggest design or construction methods. What I can do is share my company's experience in supplying road base materials by using a historical perspective in Virginia and some trends in the market that we have observed. Road building and related non-building construction are still far and away our largest markets as an industry. If we can help to improve the end product of our biggest customers, we add value to our own product. Indeed, in a time of budget constraints and competing demands for government dollars, we must show value over the life of a pavement structure to ensure their long-term funding.

Jan 1, 1996

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By R. Kuhns

The western coast of South Africa hosts a significant diamond resource within gravels associated with paleo-shorelines, channels and transgressive lag deposits. Diamonds were transported from the Kaapvaal Craton to the coast largely during the late Cretaceous via the paleo-Orange river systems. On shore and near shore environments are underlain by Proterozoic metamorphic and granitic rocks which provide gully and pot hole-type traps associated with paleo-channels, basins, bays and beaches. Inner and mid-shelf environments are covered by diamondiferous, poorly lithified upper Cretaceous and Tertiary sediments. The upper Cretaceous gravels were reworked along the sediment-starved coast during much of the Tertiary. Reworking was mainly achieved during marine flooding events which produced lag gravels along the paleo-shorelines. This process reworked the diamonds from low-grade Cretaceous gravels and concentrated them in higher-grade Tertiary gravels.

Jan 1, 1995

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997

By R. Benito, J. Lopez, H. Gamarra

This article describes three practical applications of the Hill of Value (HoV) methodology within different stages of strategic planning for open-pit mining operations and projects. In the pursuit of optimal mine planning, this study establishes a comprehensive case study during the (i)design phase, by refining key parameters for efficient decisionmaking. (ii)production planning, where the HoV is used to define achievable production rates, enhancing operational effectiveness through a nuanced consideration of mining and processing capacities. (iii)Additionally, the study introduces a conceptual framework for orchestrating the optimal sequence of multiple pits during the planning phase, with a focus on maximizing project value.

Feb 1, 2024

By W. Linwood Haden

Fullers earth has been mined since about 1920 in southwest Georgia and the adjoining area of Florida. In 1935, the mineral was named "attapulgite" after the source of a sample near the town of Attapulgus, Decatur County, Georgia. Mining and processing of the clay was described in a 1930 publication1 at a time when petroleum refiners were the major users. In the years since then, the uses and users of attapulgite have multiplied, and both mining methods and processing methods have been changed to optimize the clay for the new uses. A comprehensive review of the properties and applications of attapulgite 2 has been published. Only a brief review will be given here to explain the properties being sought and to show how these properties are optimized by mining and processing practices.

Jan 1, 1972