Search Documents

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By K. Takahashi

The methyl stretching vibrations for a series of normal and iso xanthates were determined using an infrared spectrophotometer, and the results were compared with the published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, and solubility appear to be related to the induced polarity of the alkyl groups.

Jan 1, 1968

By S. Zaharia

The authors present the state-of-the-art regarding natural and anthropic hazards on the stability of the saliferous Costiui basin. The factors that may potentially result in sliding, piping and collapse, are emphasized, given the existence of a large number of old salt mines. Also, a geotechnical risk map of this hydrosalt complex in Romania is presented.

Jan 1, 2008

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By D. R. Kelland

A program has been carried out over the last two years to apply the technology of High Gradient Magnetic Separation (HGMS) to the problem of mineral beneficiation and specifically oxidized taconite iron ores. This program, supported by the RANN division of the National Science Foundation, has consisted of a laboratory program at the Francis Bitter National Magnet Lab- oratory at MIT and a pilot investigation at the Hanna Mining Company Research Laboratory. 1 The laboratory tests were conducted using several batch type high gradient separators and a continuous separator with a rotating matrix which was constructed at the beginning of the program. The high field magnets available at F.B.N.M.L. were used for investigations above 10 kG but most of the test work was performed in the range of this field value. Ore samples were contributed by several iron ore companies and consisted of oxidized taconites having goethite and hematite as their principal components.

Jan 1, 1975

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By K. M. O’Connor

Time Domain Reflectometry (TDR) is a pulse testing technique developed by the telecommunications and power industry for use in locating breaks in cables. Variations of this principle have been utilized in applications pertinent to closure and reclamation of coal operations. This paper focuses on applications of TDR technology in the mining industry including monitoring of slope movement, abandoned mine subsidence, ground water levels and subsurface LNAPLs, landfill cover performance, and consolidation of mine tailings. TDR technology has been particularly effective for remote automated monitoring, and alarm systems have been implemented for monitoring subsidence.

Jan 1, 2003

By Vas P. Kenyen

Introduction Autogenous, semi-autogenous, and conventional grinding circuits are used to process ores. Current emphasis, though, is towards the use of the first two systems. The reason is the generally lower initial investment required for an autogenous or semi-autogenous circuit as compared to a conventional comminution circuit. However, the effect of operating costs that will significantly affect overall comminution economics is not considered in this evaluation. About 70% of the energy in a mineral processing plant is used in the comminution circuit. Until the 1974 oil embargo, energy was relatively inexpensive. Since that time, the cost of energy has escalated 40-fold. As a result, energy cost now forms a significant portion of operating costs in comminution. According to a survey conducted by General Electric Co. (Powers, 1982), the price of electricity will continue to rise 15% to 20% per year, in spite of the current oil glut. Both autogenous and semi-autogenous grinding circuits consume more energy than the conventional comminution circuit. Higher consumption ranging from 16% to 35% has been reported in the literature (Bassarear, 1982; Gjerdrum. 1979; Betts, 1982; and Christie, 1979). Consequently, even a small increase in energy costs is likely to have a significant impact on operating costs. Therefore, the economic decision of selecting an optimal comminution circuit is important. More than ever before, it is now critical to include in the evaluation of communition circuits not only the capital costs, but also the operating costs; in particular, the expected energy cost over the life of the operation. Failure to do this may lead to a less than optimal comminution circuit. Design A comminution system should be designed only after bench-scale or pilot plant testing of a representative sample. Conventional crushing and grinding circuits can be designed on the basis of the Bond Work Index (Rowland and Kjos, 1980). Over the years, sizing of full-scale rod and ball mills from Bond Work Index data has become well established. Autogenous and semi-autogenous mills cannot be sized based on bench-scale tests. Pilot plant tests are necessary to determine the amenability of the ore, critical size buildup, and power requirements. For this study, conventional and semi-autogenous grinding circuits were designed for ore throughput of 12, 24, 36, 48, 72, and 90 kt/d (13,200, 26,400, 39,600, 52,000, 79,200, and 99,000 stpd). Rod and ball mills were scaled up on the basis of the Bond Work Index. A two-stage semi-autogenous grinding circuit was designed on the basis of pilot plant test results. In designing a grinding system, emphasis was placed on operating flexibility. The largest commercially available equipment was

Jan 10, 1984

By Kenneth S. Johnson

Oklahoma is the only; state in the nation that is currently producing iodine. The iodine is extracted from iodine-rich natural brines being pumped from deep wells drilled into Pennsylvanian sandstones in the Anadarko basin of northwestern Oklahoma. Woodward Iodine Corp., started in 1977, was the first plant in the United States built for iodine recovery since the 1930s. At present, three companies are operating four iodine-producing facilities in northwestern Oklahoma. The combined production of these facilities, 1,321,000 kg in 1997, is about 26% of the U.S. annual consumption. Iodine is present in concentrations ranging from less than 100 ppm (parts per million) to as much as 1,560 ppm in brines in various Paleozoic strata in the subsurface of northwestern Oklahoma; these concentrations are exceptionally high, and are well above those of any other known brines in the world. Strata with the highest iodine content in the area (Mississippian limestones) have low permeabilities, and thus would yield only small amounts of brine. On the other hand, the lower Morrow sandstones (Lower Pennsylvanian) have a relatively high permeability and are capable of yielding large quantities of brine that average 300-350 ppm iodine. The Morrow brine reservoir was deposited in shallow-water-marine and intertidal-shelf environments and now is buried 6,000-10,000 ft below the land surface. Production is localized to Morrow channel deposits confined to an Early Pennsylvanian paleovalley that is 1-2 mi wide, is about 70 mi long, and is referred to informally as the "Woodward trench." All three companies are producing iodine-rich brines from Morrow sandstones in three different parts of the Woodward paleovalley, and one of the companies also is extracting iodine from oil-field brines coming from several petroleum reservoirs near Dover, about 80 mi east of Woodward. The basic extraction method employed by Woodward Iodine Corp. was used in Louisiana and California operations in the late 1920s. This method is commonly called the air-stripping process. Lower Morrow brine containing dissolved sodium iodide is pumped to the plant through a series of pipelines, where by-product natural gas is separated and processed. The brine is then acidified and subsequently oxidized with chlorine to convert the iodide to iodine. The iodine is air stripped and reabsorbed with sulfur dioxide and water, converting it to hydriodic acid, or process liquor. The process liquor is then processed, using chlorine once again, to crystallize the iodine as a solid. This is then melted and frozen to form a solid product, which is packaged in 110-lb (50-kg) drums and shipped to end users throughout the world.

Jan 1, 1999

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents.

Jan 1, 1981

By Patrick Doig, Ross Webb

The Bradshaw Section 5A Interceptor involves the construction of two miles of 108-inch, finished diameter tunnel in dry soils. Excavation is generally by Lovat TBM with ribs and lagging support. The tunnel is beneath a recreational parkway and stringent measures have been enacted to preserve the parkway and minimize disruption to the neighborhood. Apart from these constraints, the project would have been unremarkable but for the intervention of CalOSHA and the local fire department who ordered extraordinary fire protection measures. The paper discusses the cause and effect of these measures and comments on the potential repercussions for other projects.

Jan 1, 1999

By Williams R. Reynolds

Studies of the northeastern Mississippi bauxites were initiated primarily for the purpose of ascertaining the quality and quantity of the ore. Subsequently, this ore was found to have a rather dubious economic value as was previously suspected but never established in earlier economic reports (1, 2, 3). However, the quality of ore was found to be higher than previously thought. Even though the ore bodies were determined during the early stages of this study to be too thin, small and widespread for commercial production a continuation of the study was not abandoned. On the contrary, the present investigation was intensified concentrating less on the economic application and more on stratigraphy and genesis. Considering the ever increasing demand for aluminum products the northeastern Mississippi bauxite district which includes portions of Tippah, Benton, Pontotoc, and Union Counties may soon become, in spite of inferior quantities of ore, an attractive area for bauxite production. Presently, however, the meager quantity of ore discourages exploitation. On the other hand, these northeastern district bauxites are facies of more extensive units of lignite bearing high aluminum clays, and considering the advances in aluminum extraction from clay these clays may in the future beckon mining interest. The bauxite of the northeastern Mississippi district, mapped as a part of the Betheden Formation (4). has an outcrop trend along the county lines of Tippah and Benton Counties and the extreme western portion of Union and Pontotoc Counties. Studies of exposures and cores stratigraphically positions the outcrop between the middle Midway Porters Creek Clay and the lower Eocene Wilcox sands and

Jan 1, 1977

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as garnet and ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1983

By Dermot M. Ross-Brown

The more important factors controlling the design of pit slopes are related to the local geology over which the designer has little or no control. Nevertheless, there are some factors over which the designer does exert some control and these concern the say in which the rock is excavated and supported. They include blasting, face cleaning, water control, and the use of rock improvement techniques. The paper discusses these factors and relates the extra costs incurred to the steeper slope angles that can usually be obtained. It is demonstrated that even a modest increase in bench angle of 5° through improved excavation techniques can pay off in a single push-back.

Jan 1, 1975

By Donald P. Schlick

Gentlemen, today I would like to talk to you about metal and nonmetal mine health and safety--past, present and future. Briefly, I will comment on the past because it is important to an understanding of our present activity and our plans for the future. Federal inspection of noncoal mines was not authorized until 1966, when congress passed the federal metal and nonmetal mine health and safety act; public law 89-577, with the passage of this act, the federal inspector, for the first time, had the delegated authority and responsibility to enforce health and safety regulations designed to prevent personal injuries and occupational diseases, the new law also provided for the education and training of our miners; assistance to the operator through the transmission of technical and scientific information and assistance and equally important, the law made provision for state participation in the congressional mandate to prevent injuries and save lives in the mineral industry, Before I tell you about our program and our future plans, I want you to know that I am here to listen as well as to talk! In my view, the only kind of communication that is meaningful is two-way communication. Our nationwide progress in metal and nonmetal mine health and safety during 1972 cannot be measured in reduced fatalities or injuries. The unforeseen tragedy that took pace in Kellogg, Idaho, in may of last year mode that almost a certainty.

Jan 1, 1973

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By John B. Rigg

The title of my paper today is "public relations challenges for the pending minerals crunch". There isn't anyone in this room who would dispute. That the minerals industry has always had public relations challenges . . . No matter what the circumstances, mineral shortage or abundance. The industry suffers from an image that is second to none in longevity. It defies all actuarial formulas of the past or the future. Never mind that such an image is outdated, distorted, overstated, and reiterated. I submit that the minerals industry had public relations challenges long before there was anything called public relations. This account of egyptian mining practices, recorded for posterity by Diodorus Suculus at the end of the second century, b.c., is indicative. "On the confines of Egypt . . . And Ethiopia is a place which has many great mines of gold, where the gold is got together with much suffering and expense. The kings of Egypt collect together and consign to the gold-mines those who have been combined for crime, and who have been made captive in way . . . Sometimes only themselves, but sometimes likewise their kindred. "Those who have been consigned to the mines, being maw in number and bound with fetters, toil their tasks continuously both by day and all night long, getting no rest and jealously kept from all escape.

Jan 1, 1975

By None None

This month, Mining, Metallurgy & Exploration (MME) is launching with a special issue on mineral and metallurgical processing in honor of the 90th birthday of Prof. Emeritus Douglas W. Fuerstenau. Headed by a special review article by Prof. Fuerstenau, this special issue contains 22 papers by the top experts in the field.

By Keith S. Liddell

he selection of mill design parameters to suit the applica­tion requirements can result in quite different operating parame­ters for each generic type of application, even though the basic mechanical layout of the mills may remain similar. The selection of the type and size of grinding media is very important to efficient and cost-effective operation, and to ensuring that the milled product achieves the required properties. Accordingly, the grinding media selection is seen as an integral part of the mill design. Consideration of the requirement for classification is important in order to achieve the optimum mill and circuit performance. This can lead to the circuit feed not being classified for a steady feed with minimal slimes and a low size reduction ratio. Feed containing on-size particles would be deslimed by open circuit classification. Closed circuit classification is performed where the feed fluctuates. The rheological characteris­tics of the circuit feed slurry can have an influence on mill performance, and needs to be allowed for. A common misconception frequently encountered is the belief that "a mill is just a mill". This is not the case with stirred types of mills, since the operating parameters selected for the mill can have a large effect on the product characteristics. For example, horizontal shaft high speed stirred mills have a com­pletely different grinding action to vertical shaft low to medium speed stirred mills, which results in large differences between the surface area produced at a given product size (Liddell, 1986). Hence, it can be misleading to apply test results or design procedures obtained from one type of mill to other types for scale-up. The Metprotech stirred mill, as applied in the mining and minerals industries, is a low to medium speed vertical shaft mill. The basic design has been discussed previously (Liddell, 1989). Currently, the largest mills that have been manufactured have an installed power of 400 kW. The largest chamber volume at this power is 6000 litres, containing IO t of grinding media. It is intended that the installed power will increase up to lMW as applications requiring larger sizes arise.

Jan 1, 1995