Search Documents

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By Dominique Francois-Bongarcon

The rational and optimal determination of the design of a mining exploitation is a very intricate and difficult problem : the parameters are numerous, some technical, some economic or technico-economic which cannot be fully controlled; beside, deposits are estimated from very limited information and the choice criteria are not always quantitative, the economic context has to be anticipated by several years, and even the technological limits can change tomorrow. So, although very clever and performing numerical algorithms have been developed in recent years for open-pit design, we consider that this problem has not really been solved satisfactorily until now. The reasons are that people have concentrated their efforts on informatical algorithmical problems, and have assumed that the technical and economical data are well defined at the time of the study, which is generally not true. In particular, the mere fact of assigning dollar- values to blocks in order to maximize the total cash-flow is generally unrealistic because of the uncertainty of the data used. Consequently, the significance of the unique pit obtained as a result of these algorithms is questionable.

Jan 1, 1981

By Joseph E. Worthington

Increases in the price of gold starting about five years ago, and rapid fluctuations since then, have caused a substantial popular interest in the noble metal. Gold prospecting had been at low ebb since the end of World War II in most of the United states except for a flurry of activity in Nevada occasioned by the Carlin and Cortez discoveries. The last five years, however, have seen a great awakening of interest in gold exploration as well as an opportunity for education for many explorationists in the geology and other vagueries of gold deposits. The present writers have participated over the last few years in a search for gold deposits throughout the United States. This search was greatly influenced by the geologic studies of Dr. Wm. Spence at the Haile Gold Mine in South Carolina as reported in a companion paper. Spence's studies resulted in definition of a geologic model that has proven useful in a number of other geologic environments in the united states. These programs were all carried out under the auspices of Cyprus Mines Corporation and permission by Cyprus to present these results is gratefully acknowledged. The writers, however, reserve for themselves all responsibility for the results and conclusions. The exploration program to be described began in the southeastern United States. Spence's studies provided a reasonable basis for interpreting and understanding the geology of the Haile deposit and also provided a means for predicting additional occurrences. This concept was then expanded to other gold occurrences in the Piedmont and became an effective tool for evaluating other prospects. Finally it became evident that the concept could be applied in some western gold districts. The following discussion will then include descriptions of other Piedmont examples and a few western districts that also appear to fit the pattern.

Jan 1, 1978

By James M. Neilson

In contrast to the rather generalized title of this paper, the subject of discussion will deal with two specific cases of sliding in glacial lake clays in northern Michigan. The slides in question occurred on lands owned by the Upper Peninsula Power Company a short distance south of Lake Superior. Slope failure problems have plagued the Company's operations for many years. It is hoped that this paper may provide some insight into the causes and possible mechanisms of clay slides in general as well as providing details of the two slides specifically cited. LOCATION The Upper Peninsula Power Company's Victoria facilities lie in section 29, T. 50 N., R. 39 W., in Ontonagon County, Michigan. The power site is situated on the West Branch of the Ontonagon River, approximately five miles southwest of the town of Rockland and only one mile to the southeast of the old mining location of Victoria. The area lies wholly within the Precambrian Shield and it is geologically similar to adjacent parts of Wisconsin, Minn¬esota, and Ontario. (Figure 1). THE VICTORIA HYDROELECTRIC SITE The Victoria hydroelectric power facilities were constructed in 1930 on a portion of the West Branch where meanders are conspicuously developed. The generating station is actually sited on an abandoned meander at a place where valley widening has occurred. Water is conducted from Victoria Dam through a 6000-foot, 10-foot diameter wood stove pipe - through a surge tank - and into the powerhouse where

Jan 1, 1971

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By Jan Wolf

The iron ore industry presently utilizes two types of de-posits. The first are the high grade deposits generally located in remote areas and, secondly, the low grade de-posits which are normally found nearer to the steel-making centers. The high grade deposits produce a direct shipping ore which has an iron content which may be close to the maxi-mum 70% of Fe. These deposits have reserves which are ex-pressed in billions of tons. The ore needs little or no up-grading and where this is performed is restricted to ore washing. With the large demand for iron ore pellets, plus a national drive to perform as much of the upgrading as possible in the native country, there is a trend to erecting pellet plants at the mine location~ Large iron ore suppliers such as Australia, Brazil, Venezuela and Liberia already have pellet plants in operation, and there are new plants projected or expansion projects under study. The low grade ores are mined at locations closer to steel mills such as in Minnesota, Michigan and Canada. These low grade ores require methods of beneficiation to obtain a commercially accept-able product with the modern beneficiation techniques it is no~, possible to produce iron ore pellets of 68% Fe and 4.5% silica from ores containing as low as 26% Fe. Figure 1 gives a general picture of the types of iron ores and their beneficiation. The final product of the high grade ore is a coarse concentrate, sinter product or pellets. The final product of the low grade ores is pellets and, in some cases, coarse concentrates.

Jan 1, 1971

"Longwall shearers are widely employed in underground coal mines. The reliability of such machine has significant importance for successful mining operations. This paper aims at studying reliability of a longwall shearer using failure data recorded for a year. Data was pre-processed, sorted and selected for analysis. Selected data is then examined using statistical models. Distribution fitting of time-between-failure (TBF) and time-to-repair (TTR) are accomplished using three different models. Goodness-of-fit criteria is used to ascertain the best fitting model. Reliability in terms of mean-time-between-failure (MTBF), and mean-time-to-repair (MTTR) are calculated using the model which best represents the failure data. Exponential distribution best represents the time between failure and lognormal distribution the time to repair data. A well-known risk management technique Failure Mode Effect and Criticality Analysis is used to evaluate the critical breakdowns. Critical system/parts, experiencing regular failures is delineated based on this analysis. INTRODUCTION Mining is a capital intensive process, and huge monetary investment is required to develop and operate a mining project. Heavy and expensive equipment’s are employed in development and operation of these projects. In order to ensure timely completion of set milestones, it is mandatory that equipment’s perform their required task productively. Delays are not unusual owing to breakdown of these equipment’s. Breakdown or failure experienced by any of the equipment pose heavy financial burden. Moreover, frequent times, companies have to employ and dedicate additional resources to make up for such delays. Delays in project is not only detrimental to company’s image in market, but it also interrupts customer commitments. Mines having history of not fulfilling their promise usually get lower commodity price. Penalties are also imposed on the companies defaulting its obligations. Especially, in today’s world where competition among the companies are growing, success means keeping up the commitments in a timely manner. Heavy machinery and equipment are instrumental in success of any project. These machinery and equipment’s have to reliable in a sense that they can perform the set task in given time period. Reliability of these equipment plays a pivotal role in success of any project. The reliability analysis of mining equipment has long history. Many researchers have applied different statistical models for analyzing the reliability of mining machines (Samanta, Sarkar [1]. Kumar and Klefsjö [2] demonstrated the use of the power law process model for reliability assessments of repairable mining machines. Barabady and Kumar [3] performed the reliability analysis from failure data of the crushing plants."

Jan 1, 2018

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By P. R. Taylor

The ability to treat refractory gold concentrates that contain appreciable amounts of sulfur and arsenic, in an economic and environmentally safe manner is important to the gold mining industry. Processing alternatives include: autoclave oxidation, bacterial oxidation and roasting. Roasting may be the cheapest of all the alternatives if inexpensive methods can be found to contain the arsenic and sulfur. The research program, being reported here, has been evaluating the ability to use hydrated lime in the roaster to capture both the arsenic and the sulfur. Lime roasting is not a new idea, it was proposed for copper ores by Bartlett in the early 1970's (Bartlett and Haung 1973) and for cobaltite concentrates by Taylor in the early 1980's (Taylor et al., 1981). In addition, ores have been roasted that contained limestone and it was shown that partial capture of the sulfur was possible. Lime -sulfur containment has been proposed for the coal fired electricity industry, as well.

Jan 1, 1992

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023