Search Documents

By Ryan Marsters, Adam Pring, Robin Dornfest

Raw water supply in the central Rocky Mountains often relies on trans-basin conveyance. Many of these older diversions incorporate high-elevation, miles-long tunnels driven over a century ago in hard rock. Tunnels were excavated using conventional drill-and-blast mining and weak ground was supported by timber sets and other various means. Over time, timbers rot and fail, rock quality deteriorates, and the timbers are gradually replaced by more timber, steel patches and braces, formed concrete, rock bolts, split sets, shotcrete, and other means which are commonly applied over existing support, thereby reducing tunnel cross sections, obscuring previous support systems, and rarely addressing the failing rock itself, leading to further deterioration of both the rock and the existing support. Traditional investigation techniques to assess compromised areas are often unfeasible due to access, depth, rubble and voids behind weight-bearing existing supports, confined space, poor invert conditions, poor ventilation, and flowing water. This presentation will discuss design procedures for assessing obscured ground conditions, assigning support classes which accommodate for unknowns, and implementing contractual means to address inevitable surprises or quantity overruns. Case studies include raw water supply tunnels in the Rocky Mountain region constructed between early to mid-20th century.

Dec 1, 2022

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By Edwin B. Wilson

The purpose of the panel's examination of coal mining research and development is to explore how the various groups that make up this research community might work together more efficiently and be more productive. The community, as defined here, includes federal and state governments, coal producers, manufacturers, unions, universities, and industry sponsored research organizations. The framework chosen for these discussions consists of brief presentations by the panel members on their views of the proper role and function of the group they represent. The panel members were also asked to highlight the economic, technical and institutional constraints that affect the performance of research and development and the use of the results. Following these presentations, a number of prepared questions will be discussed by the panel, and audience participation is invited. These questions were given several weeks ago to the panel members for their study. Before proceeding with the panel member reports, a brief review of the importance of R&D to the coal mining industry would be helpful to setting the stage for a constructive dialogue. It is appropriate to begin this review by mentioning that there is complete agreement among the research community that the major goals are: Improve health and safety Protect the environment Increase capital and labor productivity Increase resource recovery Since the basic functions of the academic, industrial and government sectors are different, we should expect that the research and development objectives and priorities, roles and responsibilities under each major goal will be different for each research group. The differences do not represent problem areas. However, problems will arise if the objectives are not properly interfaced at the appropriate time. The consequences of railing to understand the need for integrated programs will be the classic result, best described by the phrase --"a technical success but a commercial failure."

Jan 1, 1978

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By D. M. Ziebarth

"During the mid to late 1960’s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace supporting a large part of the world demand; until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corporation of Saskatchewan (PCS) was one of the major producers planning upgrades to their production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1500 tonne per hour hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market. This paper will describe the design challenges encountered during the development of the infrastructure around an operating facility whilst minimizing down time, schedule, capital and construction costs. This paper will also explore the strategy to increase capacity of the newly commissioned hoisting plant. BACKGROUND Potash production is a major Saskatchewan industry, and has played a significant role in the economy for over 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in twelve companies opening ten mines by 1970. In 1975 Potash Corporation of Saskatchewan was created by the government of Saskatchewan and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine (Cory), near Saskatoon. Cory has been in operation since 1968 and is located 12 km (7.5 mi) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3300 feet) below surface. PCS has embarked on sizable capital expansions of more than CDN $7 billion. The Cory CDN $1.6 billion expansion was expected to raise operational capability of the site to 2.7 million tonnes per year, an increase of 1.9 million tonnes per year (MTPY). To achieve 2.7 MTPY of finished product and considering the 22.6% average production recovery1, 12 MTPY of ore must be hoisted to surface for processing. To deliver this rate required upgrading of the hoisting plant to 1500 tonne per hour (TPH). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly the work was completed safely"

Jan 1, 2017

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By D. E. Walsh

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No.4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10-20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove grindabilities all appear to change linearly with temperature within the 275" C to 325" C range.

Jan 1, 1997

By E. H. Christiansen

Gem-quality red beryl in the Wah Wah Mountains of southwestern Utah formed as a post-magmatic mineral in a topaz rhyolite flow. Unlike topaz, this beryl occurs along fractures in devitrified rhyolite, rather than in lithophysal vugs. The flow occupies a graben and perhaps a significant paleo-drainage. Beryl occurs at medial depths within the eroded flow, about 170 m below overlying mafic lava flows. Both beryl-bearing fractures and the host rhyolite show an unusual amount of argillic alteration compared with other topaz rhyolite flows. Alteration may be related to the incursion of surface water along shrinkage fractures within the flow. Whole-rock concentrations of CaO within the host rhyolite are very low (<0.01 % to 0.18%) compared with other topaz rhyolites and Be concentrations (about 20 ppm) are about average. Low Ca activities prevented fluorite precipitation and allowed Be transport as fluoride complexes. Beryl probably grew at subsolidus temperatures (-300-650°C), but above the temperature of kaolin development (200-300°C) as fluoride-rich vapors, released by devitrification, encountered fractures and mixed with vapors derived from surface water flowing through the fractures. Beryllium fluoride complexes reacted with water vapor, silica minerals, alkali feldspar, water, and Fe-Mn oxides along fractures to produce red beryl. Continued reaction of the cooling flow with surface water at lower temperatures probably produced a boiling, more acidic fluid that produced the argillic alteration. Consequently, eruption of low-Ca topaz rhyolite followed by entrance of surface water into medial portions of a devitrifying and still hot lava flow appear to be critical factors that led to red beryl formation.

Jan 1, 1996

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By M. D. Flavel

Research programs conducted by Allis-Chalmers Corporation are showing that the most efficient energy use in crushers is achieved when the forces applied to particles undergoing breakage are increased. Laboratory bench scale tests have been developed to confirm this phenomena, which was first observed in the field using HYDROCOME crushers with automatic setting controls. A new testing machine is described and methods of maximizing such benefits are postulated. FOREWORD Allis-Chalmers Corporation was founded in Milwaukee, Wisconsin, in 1847 as the E. P. Allis Company, which had an initial interest in manufacturing components in the grinding of flour. As such, its roots were started in reducing material size, which is covered by the generic term, comminution.

Jan 1, 1981

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner&apos;s drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By S. Kemball-Cook, D. Heinze, A. Kornberg, M. Harmon

Climate change presents risks to mine infrastructure, operations and long-term obligations to protect environmental conditions. Management strategies and design of infrastructure and containment systems based on past or current climate conditions may be inadequate in the future if changes in climate are not taken into account in planning for mine operations, decommissioning, closure and post-closure. Data-driven assessments using climate model projections of the future can be used to quantify: • Changes in site-specific risks to mine structures, access, containment facilities, operations and staff safety. • Changes in vegetation and water balance/chemistry, and potential for acid mine drainage, erosion and design failure. Climate- and weather-related risks are a serious threat to the mining industry, but risk transfer solutions can alleviate these vulnerabilities. Mining companies can protect themselves through bespoke solutions which provide operators, investors and buyers with protection against weather-related disruptions to operations by hedging to smooth revenues. Using risk transfer structures to mitigate climate risks is a mechanism that is available to all types of mining operations world-wide. In this paper, we describe methods for evaluating site-specific climate change impacts and developing risk transfer solutions to mitigate their effects. EVALUATING MINE RISKS FROM CLIMATE CHANGE The best available tool for understanding potential future changes to the earth’s climate system are global climate models (GCMs) (IPCC, 2014). GCMs are computer simulations of the climate system which include the atmosphere, ocean, land surface, cryosphere and biosphere. Because of the computational demands of running a global model for many decades, the spatial resolutions of the GCM grids are necessarily coarse, typically on the order of 100-300 km. GCM data are therefore suitable for evaluating future physical risks on global or continental scales, but may not be appropriate for evaluating location-specific risks (e.g. Kotamarthi et al., 2016). For site-specific, quantitative physical risk assessment, GCM projection data are “downscaled” or adapted for use at the local level using statistical techniques together with observed data (statistical downscaling) or using high-resolution regional climate models (RCMs) that focus on a single geographic region and have spatial resolutions of 10-50 km (dynamical downscaling). Downscaling bridges the gap between the GCM scale and regional/local scale. Through the downscaling process, new information is added to the GCM output from observations and/or RCMs, resulting in patterns for weather variables that are more consistent with local terrain and weather influences. Downscaled climate change projections for the mine site are selected considering mine location and geography, the availability of local observations, and the performance of the downscaling method and global/regional models used to develop the projection in simulating the variable under study. Where possible, we use projections from an ensemble of global and regional model runs spanning a range of future greenhouse gas (GHG) scenarios.

Jan 1, 2019

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021