Search Documents

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By A. J. Van Der Merwe, J. F. Erasmus

One of the valuation approaches applied to Advanced Exploration Areas and Pre-Development Projects is the so-called ?in situ Mineralization Method? or the ?Yardstick Method?. This method is based on the concept of a known undeveloped Mineral Resource being worth a certain fraction (the ?Yardstick?) of the contained commodity value (?metal in ground?), using commodity prices ruling at the date of valuation. The Yardstick value is derived usually from an average market-based figure obtained from an analysis of recent transactions and is expressed as a monetary value per ounce or per tonne. It maybe modified to accommodate the quality (e.g. grade) and category (e.g. confidence level) of the Mineral Resource/Reserve involved and the time, effort and expenditure expected to be involved in bringing the project to fruition. Some eighteen recent and relevant transactions were analysed, allowing the following general conclusions to be reached: ? a Yardstick with which to value undeveloped PGE mineral resources is likely to range between 0.5% and 2.5% of the in-ground contained metal value ? the expected method of mining (especially with regard to mining costs) and the grade of the mineralization both have a strong influence on the Yardstick ? the status (classification) of the Mineral Resource has some influence on the Yardstick and ? the ruling price of platinum and the regional location of the deposit appear to have insignificant influences on the Yardstick.

Jan 1, 2006

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where 'visual pollution' is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the 'fine' and 'coarse' size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and 'coarse' particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By A. Wedepohl

Selective leaching of phases in charge chrome is used in a variety of industrial processes for the production of chromium chemicals. A mineralogical study was made of a range of local charge chrome samples, at various stages of leaching in sulphuric acid (20g/l at 90°C), using mainly a scanning electron microscope (SEM) together with an energy-dispersive spectroscopy analyzer (EDS), and X-ray diffraction techniques. It was found that the leaching behaviour of the different types of charge chrome depends largely on the nature of the secondary phases, which in turn depends upon whether the silicon content is above or below 4 per cent by mass. The leaching behaviour of high-chromium ferrite is anomalous, and it is postulated that the process is analogous to the corrosion of brass by dezincification. Keywords: charge chrome leaching, scanning electron microscope

Jan 1, 2000

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By S. Montes

Mineral floatability is strongly connected with mineral structure and composition. The complexity of mineral surfaces has meant that few attempts have been made to understand the effect of impurities (trace elements) on the flotation process. Zeta potential technique has been extensively used to evaluate the surface charge of mineral particles. Nevertheless, those measurements consider only an average of mineral particles surface charge. The presence of fine particles and inclusions covering a mineral may influence the local reagent adsorption process, which will ultimately be reflected in the subsequent global response of the mineral froth flotation efficiency. The current work assesses the iron oxide mineral, haematite (Fe2O3). Zeta potential and streaming potential techniques were used to determine the surface charge of fine and coarser particles of haematite. Further analysis was performed to determine the point of zero charge (PZC) of the mineral. In addition, adsorption isotherms of alkyl ammonium chloride reagents with different lengths of carbon chains were carried out. It was found haematite floatability depends strongly on the isoelectric point (IEP) value, which is affected by other mineral species present at the mineral surface. Haematite floatability became significant only at relatively high tetradecyl ammonium chloride collector concentrations (concentration greater than 4 10-4M), which does not happen with other oxides such as quartz. Unlike quartz, haematite develops a low surface charge over a wide range of pH, disabling all long-range attractive interactions between the mineral and the collector. Therefore, hydrophobic chain interaction is probably the most likely mechanism acting to promote collector adsorption and enhance further floatability. Diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to suggest a possible mechanism to understand the sequence of collector adsorption and the effect of trace species on it. Keywords: floatability, haematite, adsorption, electrochemistry, zeta potential.

Jan 1, 2007

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By Y. Wang, S. Sridhar, B. Coletti, G. N. Shannon, S. Vantilt

The final removal of inclusions in the ladle, tundish, and mold in a continuous casting process involves the kinetic steps of liquid film drainage, interface rupture, and absorption of the inclusion into the overlaying molten slag. During this process, oxide inclusions can undergo chemical reactions with the slag. This paper presents recent results on imaging the slag/steel interface and elucidates the evolution of Al2O3and Al2O3-CaO inclusions during their separation from the steel and on their incorporation into the slag. Experimental results, obtained through a Confocal Scanning Laser Microscope, are compared with thermodynamic predictions.

Jan 1, 2004

By A. B. Fox, R. P. Thackray, K. C. Mills

The role of mould fluxes in continuous casting is reviewed. The main functions of the flux are described and the importance of the flux in providing lubrication and the right level of heat transfer between the shell and the mould is described. The major problems of longitudinal, transverse and star cracking, gas and slag entrapment and deep oscillation marks in the steel product and ?sticker breakouts? are analysed. The important physical properties of the flux in combating these various problems are identified. Physical property data for the fluxes are given.

Jan 1, 2004

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By V. V. Nazimko, A. I. Hohotva, S. N. Alexandrov, V. P. Sazhnev, V. S. Zaharov

Ground behaviour in the vicinity of a roadway has been investigated using a physical model and in situ tests during a roof fall. It was discovered that behaviour of the ground is governed by irreversible displacements of adjacent rock clusters. The cluster is a short-living sector of a rock mass that moves as a solid body. For the lack of degree of freedom, the rock mass must be divided into clusters that are forced to move one after another in space and in time. These clusters permanently rearrange and reform during irreversible (inelastic) ground deformation. The crowded clusters have to yield to each other and alter their velocity and direction of movement to accommodate their motion into the excavation. Such behaviour involves uneven and irregular vertical deflection and the movement of adjacent rock blocks in the roof, sides and floor of an opening. Such movement destroys the symmetry of horizontal displacements with respect to the centre line of the opening. A set of indicators that a roof fall is imminent has been identified. Horizontal displacements and dilation must be controlled in order to maintain the stability of an underground opening. Such a state retains the self-supporting effect of the roof and contributes to rock bolts bearing capacity.

Jan 1, 2003

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007