Search Documents

By Aaron L. Sacks, David R. Good, Srinivas Yennamanda, Joseph K. Carey

Construction of Parcels 6 and 7, the second phase of The Wharf, began in 2019 and geotechnical construction was completed by December 2020. The overall project consisted of horizontal site, parks, and office buildings. The Wharf’s Phase 2 development includes approximately 1.2 million ft2 (110,000 m2) of above-grade construction including five multi-story, mixed-use buildings constructed over up to three levels of underground parking. The site is located between the WMATA Green Line Tunnels to the north and the Washington Channel to the south; it is bisected by a 108-in. (2740-mm) diameter DC Water outfall pipe. This arrangement, along with very difficult ground conditions, created challenges in the geotechnical design and construction. The support of excavation for this complex project required several different methodologies, including sheet piles, soldier piles, displacement piles, tiebacks, deep foundation anchors, jet grouting, and internal bracing with multi-tier rakers. Ground improvement was also required for support of spread footings in soft soils over the garage footprint. Underpinning of the active 108-in. (2740-mm) diameter DC Water outfall pipe running on a north/south alignment through the center of the site between the two garage structures was also performed. Since portions of the support of excavation are below the groundwater table, an extensive pre-excavation dewatering program was necessary and was separate from the foundation package. On the north side of the project, support of excavation (SOE) was required on a curved alignment, offset approximately 10 ft (3 m) from the outbound Green Line tunnel. Due to the proximity of the tunnel, a stiff, near-zero displacement wall was required. A portion of the buildings extend over the tunnels, imparting load to the tunnels to approximately restore original overburden loads excavated for the basement space. The building foundation is a 3 to 4-ft (0.9 to 1.2-m) thick mat slab anchored into the Potomac clay formation. Continuous movement monitoring of the tunnels was performed by an automated system. This paper describes the design and construction of the SOE and foundations for this high-profile project, which required collaboration between the Owner, Engineer, Construction Manager, and Specialty Geotechnical Contractor to solve many challenges.

Oct 1, 2022

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Stefano Pirrello

"Sydney’s booming real estate market has pushed property developers to invest in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement Piles (DD) techniques are on the other hand suitable for these ground conditions. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West. The advantages of DD over CFA piles such as reduced overall spoil with substantial cost savings and achievable rock sockets in medium strength bedrock are discussed. Design validation through interpretation of real-time data from the piling rigs’ on-board computer data, and low and high strain pile dynamic testing (PDA) is discussed. Testing data is presented as CAPWAP (Case Pile Wave Analysis Program) analyses for different concrete grades.INTRODUCTIONThe booming real estate market in Sydney has pushed property developers in investing in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement (DD) Pile techniques are on the other hand suitable for these ground conditions and were utilised using concrete injection methods. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West.GEOLOGY & GEOTECHNICAL CHARACTERIZATION OF THE SITEThe Sydney 1:100 000 Geological Series Sheet shows that the site is underlain by man-placed filling and alluvial/estuarine sediment. The sediment comprises silty to peaty sand, silt and clay. Shell layers are also expected to be present within the soil profile. The Prospect/Parramatta River 1:2500 Acid Sulphate Soil Risk Map shows the site as ‘Disturbed Terrain’ in which soil investigations are required to assess acid sulphate soil potential. Several Cone Penetration Tests and Boreholes were carried out during the geotechnical investigation. All boreholes were extended to bedrock and NMLC-sized diamond core drilling was used to obtain 50mm continuous core of the rock, enabling unconfined compression strength testing to be carried out on selected samples. A summary of the ground conditions encountered on this site and inferred from the CPTs can be described as follows:"

Jan 1, 1900

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; and forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2009

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Rahul Wankhade, Sunil S. Baswankar, Aditya S. Kharatkar

Despite advances in pile design methodologies and piling techniques at site, difficulties and uncertainties still exists for design of piles particularly in coralline deposits and weak carbonate rocks. Such deposits are known to be heterogenous in nature, and occupy major stretches of earth, where piling experiences are probably very scanty. Such deposits are associated with low unit weights and usually consist of weakly cemented calcareous and carbonate soils interbedded with coral rocks containing cavities, which are completely void or filled with coral debris. Many of the studies indicate that conventional parametric relationships are may not apply to such sediments and rock formations. This paper intends to provide an appraisal of the available information that cautions against risks involved in conventional design practice and also serve as a guideline for pile design in such formations despite being a grey area of research. Contents of the paper is expected to provide a basis for the pile design and likely to serve as an eye-opener for research into this important soil-pile structure interaction problem.

Sep 1, 2022

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Clayton A. Signor

Abstract: Expansive soils cause more damage to structures annually than a combination of other major natural disasters. Because of the cost to our society, all means and methods need to be fully explored to mitigate the problems associated with expansive soils. This study will present a foundation design approach that is underutilized in this application, driven piles. The main objective of the study is to present pile test results and analysis from four driven pile project sites in three types of expansive soils found in central Texas: Del Rio formation, Taylor/Navarro formation, and expansive alluvium. High strain dynamic pile tests were conducted on each of the four studies with rigorous signal matching analysis from the CAse Pile Wave Analysis Program (CAPWAP). Ultimate pile capacities ranged from 73 to 311 kips with an average of 61% of the total capacity coming from the pile shaft and were two to six times the structural capacity needed. Allowable loads calculated from Modified Gates dynamic formula best modeled allowable test results. Average unit skin frictions ranged from 0.50 to 4.71 ksf. Restrike pile tests of 1 to 17 days after initial driving reported 30 to 100% shaft capacity gain. All open-ended pipe piles driven produced soil plugs ranging from 4 to 14 feet thick. Small diameter, thick-walled, open-ended pipe piles reached penetration of twice the depth of designated zone of seasonal moisture change without problem. The observed production rate of the driven piles was on average 8 minutes, which implied daily production of 15 to 40 piles. Predrills or augered holes should be specified for underground obstructions found in soil investigation.

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By Chris Normand, Paul Volpe, Eric Wey, Howard Perko, Burt Ogilvie, Patrick Murray

"A refinery expansion project for Marathon Petroleum Company in Southern Louisiana required existing medium to large pipe racks to be expanded for additional capacity. Foundation modifications were necessary in order to add levels to the existing pipe racks. New piles were added and existing pile cap foundations were expanded. Several different pile types were considered. Custom designed large diameter helical piles were chosen, because they can be installed quickly with low overhead restrictions, produce minimal soil spoils, and are cost effective. The load capacity required for piles was higher than typical, off-the-shelf helical piles. In particular, the lateral load capacity demand was high due to wind loads of a hurricane prone region. Methods used to design and size helical piles are summarized including capacity to torque ratio estimation for composite helical piles. Pile load testing was performed in order to confirm design capacities of the helical piles under axial and lateral loading. Measured axial and lateral deflections compared well with predicted values. This case history evaluates the effectiveness of modern helical pile design methods within the context of a real and practical example.INTRODUCTIONAs the capacity of modern installation equipment increases, large-diameter helical piles are being used to support higher loads in more diverse applications. Currently, large-diameter high-capacity helical piles are used for electrical power transmission, power generation, high-rise buildings, bridges, and industrial applications. This case study regards a 2.5-mile pipe rack modification project within an existing refinery. One of the many challenges for engineering and construction of refinery revamp projects is determining how to effectively expand the capacity of existing foundations for additional equipment, piping, and other facilities. Custom designed large-diameter helical piles provided an effective solution to the challenges faced when expanding the capacity of existing pipe racks."

Jan 1, 2017

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996