Search Documents

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Gihan E. Abdelraham, Youssef G. Youssef, Mohamed M. Kamel

"Previous studies defined Narrow Mechanically Stabilized Earth, NMSE, walls as a retaining wall with aspect ratio (wall width to its height, L/H) less than 0.70 as in traditional walls. Some studies investigated its behavior and its failure planes compared to those of traditional walls. In this paper, parametric study using finite element analysis PLAXIS, 8.2 has been introduced to discuss global factor of safety, FS, maximum horizontal displacement, Ds, maximum tension force of reinforcement element, Tmax, and active earth pressure coefficient, ka, as a function of different aspect ratio of NMSE wall, L/H, reinforcing elements spacing, S, elastic axial stiffness of reinforcement element, EA, wall batter, 1/m, soil friction angle, f, and wall height, H. The results indicated that increasing aspect ratio increases the factor of safety, maximum horizontal displacement, maximum tensile force and active earth pressure. Increasing elastic axial stiffness increases factor of safety, maximum tension force of reinforcement element while decreasing the maximum horizontal displacement.IntroductionReinforced earth is a composite geoconstruction material, which embodies two basic components; namely engineering fill and reinforcing elements. The latter one is responsible for improving the tensile and shear resistance of the soil. The soil-reinforcement technique has been in use for many geotechnical applications especially MSE walls.A narrow wall system is referred to as a MSE wall with an aspect ratio, L/H, below 0.70 that is placed in front of a stabilized wall. An example of a narrow wall system with its dimensions is illustrated in Fig. 1."

Jan 1, 2017

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By Rajarshi Pramanik, Nirjhar Dhang, Dilip K. Baidya

"This paper performs the reliability evaluation of pile foundation under vertical loading condition using the concept of fuzzy set theory. The uncertain parameters are expressed as fuzzy numbers. Monte Carlo simulation technique in conjunction with fuzzy set theory and fuzzy reliability index approach are implemented in evaluation of the probability of failure of pile foundations. The results are validated through some well established methods such as, First Order Reliability Method (FORM), Second Order Reliability Method (SORM), and direct Monte Carlo Simulation (MCS). Response surface method (RSM) is used to approximate the original limit state equation through second order polynomial. The effect of the position of the water table is also highlighted. Finally, the effect of the variation of applied load is examined and it is observed that the fuzzy reliability analysis gives more conservative estimate of failure probability than the other methods.INTRODUCTIONCivil engineering structures, such as high rise buildings, bridges, offshore platforms etc. are always subjected to vertical as well as horizontal loads. To support these structures, pile foundations are generally the solution in most of the situation. It transmits load from the superstructure to soil at a reasonably great depth. This transfer may be by vertical distribution of the load along the pile shaft or a direct application of load to a lower stratum through the pile tip. Different methods are available to estimate the capacity of piles embedded in different types of soil and under the application of vertical and horizontal loading. To consider the variability in soil and other unforeseen able situation, generally a reasonable value of factor of safety is used to estimate the designed capacity of the pile. Recent developments have shown a trend to place the treatment of uncertainty on a more formal basis, in particular by applying the results of reliability theory to geotechnical engineering. Keeping in mind the importance of pile foundation in the engineering structures it is essential to maintain a high structural safety which result in increase in reliability. The probability theory has been proved to be a powerful tool for representing variability in mathematical models. The variability associated with soil parameters and the modeling uncertainties are needed to be considered for the reliability assessment purpose.Recent development (Zhang et al. 2005; Misra and Roberts 2006; Haldar and Babu 2008; Basu and Salgado 2012; Teixeira et al. 2012; Pula and Rozanski 2012; and Chan and Low 2012) showed that the reliability analysis of pile foundations subjected to axial as well as lateral load has been one of the important current research topic in geotechnical field. Probabilistic based performance criteria were quantified for a single pile and pile groups in cohesionless soil by Eloseily et al. (2002). A p-multiplier approach was incorporated into the analysis to modify the p-y curve for a single pile to obtain the p-y curve for individual piles in a pile group. A statistical analysis of set up capacity of pile was carried out from the database of a large number of pile testing data in clay by Yang and Liang (2006). Load and resistance factor design (LRFD) using FORM was used for examining the different load and resistance factor for different target reliability index. Limit state analysis of drilled shaft was performed by Misra and Roberts (2006) in probabilistic framework. The fuzzy based reliability analysis (Dodagoudar and Venkatachalam 2000; and Park et al. 2012) of the earth slope was reported in the literature. Dodagoudar and Venkatachalam (2000) presented a new approach, called fuzzy point estimate method (FPEM) for reliability evaluation of earth slope. Park et al. (2012) reported a hybrid approach, fuzzy set theory in conjunction with Monte Carlo simulation technique, to determine the failure probability of earth slope. Second Order Reliability Method"

Jan 1, 2015

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Rae Mackay, Kaveh Ranjbar Pouya, Ali Tolooiyan

"A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Due to the low strength of CIS, most construction in the region is based on pile foundation systems. Traditionally, the design of pile foundations is mostly based on empirical and analytical methods. However, numerical methods such as Finite Element Methods (FEM) can be utilised for more accurate estimation of the bearing capacity and deformation of pile foundation systems, especially in complex loading scenarios. Unfortunately, no systematic effort is made yet to calibrate a realistic nonlinear constitutive model to describe the geomechanical behaviour of CIS in a numerically based solution. Among the nonlinear constitutive models, the Hardening Soil (HS) model is an advanced hyperbolic model which accounts for the nonlinearity of stress-strain relationship as well as the stress dependency of the soil stiffness. In this study, the HS model is calibrated based on laboratory tests performed on CIS. Also, to validate the accuracy of the calibration, the wellknown cavity expansion theory is employed to model the CPT cone tip resistance (qc) in CIS, and results are compared against the measured CPT qc profile at the field.INTRODUCTIONA large percentage of world’s coastal areas are covered with soft marine clay deposits. Having very low shear strength and high compressibility, the alluvial deposits are known as one of the most problematic soil layers for the design and construction of infrastructure facilities. A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Basically, there are two main solutions for construction in such weak soil conditions. One is the use of pile foundations transferring the applied load to deeper and stronger soil layers, and the second one is to employ ground improvement techniques such as using deep soil mixing columns to improve the bearing capacity of the soil. In both cases, a practical geotechnical design should incorporate both stability analysis and deformation analysis to achieve a cost-effective and reliable solution. Most of the classic solutions for stability analyses such as limit equilibrium analysis disregard the stress-strain relationship of the soil for the sake of the simplicity (Chen, 2007; Sokoloviskii, 1965). In a similar simple approach, most of the past studies of deformation analysis have been established on the basis of linear elasticity. However, it is well recognised that the soil stress-strain behaviour is highly nonlinear even at very small strains (Burland, 1989). Hence, for a precise deformation analysis of the foundation of important geotechnical structures, the application of advanced nonlinear constitutive models is extremely beneficial. Precise deformation analysis is essential as geotechnical designers have to predict the displacement of geotechnical structure and the adjacent soil as well as the induced displacement and forces to adjacent structures. This issue is more highlighted recently in the analysis, and design of highly important infrastructures as geotechnical engineers are facing new challenges in the analysis and design of infrastructures in congested areas. Rapid population growth, especially in the major cities all around the world necessitates the design and construction of more integrated infrastructure facilities. Consequently, geotechnical engineers should employ more advanced design approaches to address the new challenges in geotechnical engineering practice. Complicated geometries, different loading scenarios and the application of nonlinear deformation models which is believed to be essential for a precise deformation analysis, necessitate the application of numerical methods to satisfy most of the design requirements."

Jan 1, 1900