Search Documents

By Collins BJ

Basic principles of stack injection are outlined and supported by calculations of thermal, chemical and aerodynamic requirements of an ideal 4000 tpd furnace. Calculated results show that these requirements vary with conversion of FeO, and that best performance may be expected with XFeO = 1.0 for which calculated production is 6919 tpd and coke rate is only 211 kg/thm. Calculations are also presented for a cycled injection. Discussions show that stack injection is a good way of overcoming softening problems and meeting the demand for iron in a fluctuating demand situation when it exceeds the maximum capacity of a furnace.

Jan 1, 1975

By Johnson M, Gaudin A

With the advent of Computer aided mapping and surface modelling techniques Geologists and Engineers have had to become familiar with the capabilities and limitations of these systems to effectively use them. In this paper we will trace a short history of the rather rapid progress in this area. From this historical perspective we will make some observations and use these to guess at what the future holds. We hope that this paper will assist in clarifying the develop- ments in computer assisted mapping and modelling and promote thought on how these techniques may be best applied to the problems of the Mineral Industry.

Jan 1, 1983

This paper reviews factors involved in the feasibility stage of underground mine project development. Emphasis is placed on the need to first select the best method of extraction and make the most accurate assessment of the expected output even with the uncertainties which may exist in structural interpretation, ground stress, geotechnical factors, and industrial conditions. The subsequent engineering planning should be undertaken from the point of view of the face requirements and is subject to constraints imposed by the method of work and nature of the deposit and, in the case of access, to surface constraints and services.

Jan 1, 1983

By M Watts, P Lindsay

Herbert Stream, a tributary of the Waimangaroa River on the Stockton Plateau, has elevated metal concentrations and low pH characteristic of acid mine drainage (AMD). Dissolved aluminium concentrations average 8.3 ppm, iron 1.4 ppm, manganese 0.69 ppm, and zinc 0.12 ppm and pH ranges from 2.8 to 3.2. Flow rates range from 2.3 to 26.6 L/s with an average of 5.3 L/s. To determine the effectiveness of different treatment strategies, a small amount of the AMD was diverted through three small-scale passive AMD remediation systems over an eight month period. These included a reducing and alkalinity producing system (RAPS), a limestone leaching bed (LLB), and an open limestone channel (OLC). Both the RAPS and the LLB performed well, effectively removing metals and restoring pH. The RAPS lowered aluminium concentrations by up to 99%, iron 97%, manganese 95%, and zinc 80% and the LLB lowered aluminium concentrations by up to 99%, iron 99%, manganese 92%, and zinc 91%. The pH was restored to between 6.4 and 7.4 by the RAPS and to between 7.3 and 7.9 by the LLB. The OLC performed well as long as the residence time was similar to that of the other treatment systems. OLC removal rates for aluminium was up to 99%, iron 94%, and manganese 21%, and the pH was restored up to 5.6. Due to its simplicity and effectiveness, it is proposed the LLB be constructed to fullscale size to treat the entire Herbert Stream.

Jan 1, 2007

The Bradford Process, Australian Patent No. 11253, has had considerable application in the treatment plants of Broken Hill mining companies, and is at present being used by the North Broken Hill Limited for the treatment of weathered slime accumulations.The "Mining and Scientific Press," of 28th September, 1918, describes the Bradford Process at Broken Hill, specially featuring its application to slime material at the Proprietary mine-the home of the process.The points then stressed for galena flotation were acidulated slime pulp (0.025 to 0.030% H2S04) at temperature 85° to 90° F. and suitable time contact, with 1.5 to 2 lb. of sodium hyposulphite (per ton on slime) to permit the released S02 to "wet" or depressthe blende mineral. Also 1.0 to 1.3 lb. of crude sulphur (per ton on slime) was burnt, to supply S02 for keeping the lead concentrate clean during flotation. Pulp density varied from 23 to 26% solids. Since 1918 the process has been simplified in its application.Acidity of circuit, temperature, and sodium hyposulphite have been dispensed with, and now the S02 is practically all obtained by burning crude sulphur. I The plant units now employed for control and absorption of S02 gas constitute the main advance made in process, and these, with other details, are fully explained in this paper.APPLICATION AT BROKEN HILL NORTHThe existing North Broken Hill Limited gravity mill commenced operations on 9th September, 1909.

Jan 1, 1929

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

Fleet management systems have been adopted by many open pit mines throughout the world and the resulting improvement in truck cycle times has been one of the most significant contributors to mine efficiency. Ongoing enhancements to fleet management systems such as interfaces for vital signs monitoring have given incremental efficiency gains. Each incremental improvement is another step towards a grand vision of a totally automated mine. A relatively new fleet management system is being integrated with two other technologies to provide a highly reliable platform for a networked information system which monitors mine machinery and production. The paper reviews the integration project, the features of the new mine site information network platform and the contribution to productivity and safety. The new fleet management system has a predictive truck dispatch algorithm. It also has a distributed database that replicates rapidly so that each machine in the fleet has an identical database, thereby making each machine aware of other machinesÆ locations on the site. High precision systems for navigating and monitoring machinery such as drills, dozers, draglines and shovels provide individual machine operators with cockpit style real-time information to increase their operational efficiency. The integration of the new fleet management systems capabilities with the high precision systems that provide production information, machine vital signs data and operator information means that the mine operations and maintenance managers have real-time access to the whole mine siteÆs production data. Such a mine monitoring and reporting system is dependent on reliable wireless communications and reliable positions. Positions in fleet management and high precision systems for open pit mines are usually provided by global positioning system (GPS). Other global navigation satellite systems (GNSS) such as Glonass, and in the future Galileo, will provide additional satellite cover; however, some parts of open pit mines do not have enough sky visibility for reliable GNSS positioning and so a new centimetre level wireless positioning system called Locata is being integrated with the fleet and high precision systems to augment and backup the GNSS positions. The final integrated system will provide the highest levels of reliable position-based information to all stakeholders in a mineÆs operation, ensuring gains in productivity and safety.

Jan 1, 2008

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

The purpose, basic data requirements and various analysis/modelling tools employed for geomechanical evaluation of mine-site conditions are overviewed. The impact and application of computer technology are dis- cussed. Broad guidelines and criteria are presented for establishment of a practical geomechanics data-base system to yield infor- mation suitable for mine design purposes. Future needs of the Australian mining in- dustry are examined.

Jan 1, 1983

By P Mugebe, M Yahyaei, M S. Kizil, R Low

This paper seeks to establish an empirical relationship between the impact of mining technological innovation implementation and a company’s market value. The company’s market value is represented by its stock price. In a bid to ascertain the relationship, a stock price prediction model is sought to be established using the firm-specific factors impacted by the implementation of innovative technology. This work is performed under the watch of the prevailing macroeconomic factors. The background anchors in the understanding that the difference between the economic status of a mineral deposit and its uneconomic status lies in the level of mining technological innovation most prevalent at a given time (Hartwick, Olewiler and Preuss, 1986; Wellmer and Scholz, 2017; Wright and Czelusta, 2003). This is derived from productivity improvement, resulting in sustainable profitability due to technological innovation. Unfortunately, there is not an adequately established relationship that links this technological innovation impact to the share price performance of the mineral commodity company.

Sep 1, 2024

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

Completion of a project requires two separate money-focused activities, namely economic evaluation of the cash flows underlying the project (before financing) and if the economics look promising, how it can be financed. Economic evaluation might be best led by a person with a technical-operating background, whereas financing might be best led by an accountant. Both should be presented in simple language with easy to understand models. Economic evaluation has a sad and bad history because it evolved from the fringes of accounting. Anyone can become a self-appointed practitioner. Some still take pride in mathematical complexity without realising that they distance themselves from the decision-makers and alienate other team members. Today there is no evaluation modelling consistency across the mining industry and this reflects poorly on our discipline. It is not tolerated amongst our peers in engineering and accounting. In 2009 æbest practiceÆ economic evaluation modelling is well defined. It is:easy to follow;tailored to its purpose;transparent;discipline, rigour and consistency;recording of all source data; and hencequick to audit. Mantra: If you cannot readily understand my model you do not have a problem, I do! The task of the economic model is to make the range of business cases underlying the decision easy to understand. Intellectual power is used to simplify the decision to its key issues and risks and to present the full range of possible business outcomes in readily understood terms. Project team members, management and the board must be able to make their decisions with æeyes wide openÆ. A steering committee should be established to develop a set of standards and practices that could be adopted for economic modelling within the industry. The industry needs to purge itself of the undisciplined economic evaluation modelling that now characterises the discipline.

Jan 1, 2009

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018