Search Documents

By C. G. Dunn

IDENTIFICATION Of the kinds of orientation relationships that may exist among crystals is an important problem in the metallurgical field. As an aid to its solution standard orientations of several orders of twins would be very useful for rapid analyses to discover high-order as well as low-order twin relationships. Although data have been published that give orientations for three generations of twins, these data are not readily useful in the form presented; i.e., in a stereographic projection with one pole per orientation.1 However, accurate data based on calculations of the positions of all {100} planes for such groups would be very useful when presented in tabular form. Therefore, calculations have been made for a group of four orders of twins and the data are listed in Table 3. Illustrative applications are considered briefly, with the idea of pointing out what may be done with large groups of orientations. METHOD OF COMPUTING ORIENTATION OF A TWIN It is common practice to describe the orientation of a crystal in terms of the positions on a stereographic net of the poles of certain planes of the crystal. A single position on a net may be given it terms of two angle variables, two sets of which appear in the following equations: [Polar NetWalff Net x=rsinOocos4pyx=rcos0. y=rsinB,sin4,ny-rsin0.cos¢,, z=rcos0,,z=rsin0.sin4,,] The three numbers x, y and z determine a length r as well as a direction [(0, 0)] in an X, Y, Z coordinate system. In the present case, r will be set equal to (h2 + k2 +12)1/3, where h, k and 1 are the usual Miller indices for a crystallographic plane, a restriction that facilitates determination of the positions of poles of new planes from those of old or known ones,2 as will become evident later. Furthermore, since twinned lattices have certain planes in common, it is an easy matter to determine the orientation of a twin of a crystal if the orientation of the crystal itself is known. We start therefore with a crystal of known orientation (positions of three {100} poles given) and determine where the cube poles occur in first, second, third and fourth-order twins. Methods for identifying twinned lattices and for making the calculations to find the orientation of a twin have been published.3 4 Reference 4 will be illustrated in the calculation of the orientation of a twin, even though this method differs from the one used by the writer in obtaining the following data on four orders of twins. Consider a crystal S and its twin A1, A1 being one of the four {112} or {III}

Jan 1, 1945

By H. A. Buehler

The Ozark region occupies a large part of the southern half of Missouri, the northern portion of Arkansas and comparatively smalll areas in northeast Oklahoma, southwest Kansas, and southern Illinois. It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The Boston Mountains extending for a distance of some 200 miles (321 km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Frangois Mountains in St. Frangois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.). The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. Stratigraphy The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Frangois Mountain district. Although located geographically near the eastern edge of the Osarks, the St. Frangois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Gene-vievg County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous action, since the first sedimentary beds were deposited.

Jan 1, 1918

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2'3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By E. H. Rose

THE present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: I. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. ANALOGY WITH GRINDING In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1944

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors' determined the constitution of copper-silicon-manganese alloys containing over 90 per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper .2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 20 c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. Table I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. A few other changes will be noted (No. 138 at 450°C., No. 149 at 550°C., Nos. 153 and 149 at 750°C.). The change from liquid to beta in equilibrium with kappa in No. 139 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. 1 to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the [K = a + ?] change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300° and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 ± 0.03 per cent or 2.42 ± 0.05 per cent were cast in ingots of 3-in, diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 900°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Hoyt Stoddard Gale

Recent work on borate deposits near Kramer in the extreme southeast corner of Kern County, California, is of special interest because of the information it seems to give concerning the mode of origin of the borate minerals colemanite and ulexite, especially when considered in conjunction with the valuable clue to the mode of origin of colemanite in its present known deposits given in a paper by W. F. Foshag,1 of the United States National Museum. Colemanite is found in or near original deposits of ulexite, from which it is supposed to have been derived by a change in the character of the ground water or rate of its movement or both. Indications that an alteration of this sort had produced colemanite were first recognized by the writer2 in specimens collected in the Kramer district in 1920, and sent to W. T. Schaller, at U. S. Geological Survey, for identification. The identity of the two borate minerals in these specimens was suspected when collected but not at once determined, but the relations of the minerals as seen in the specimens seemed to afford a manifest clue to the origin of the deposits. Similar specimens were obtained by the writer from deposits in Death Valley soon after he had examined the deposits near Kramer. After studying the specimens submitted to him Dr. Schaller wrote as follows: " I have finally positively identified the boron minerals you sent me with your letter of Sept. 27. The 'white fibrous mineral like ulexite, is ulexite; the 'harder nodules' in the clay are colemanite, apparently formed from the ulexite as a result of leaching, with recrystallization in place—a theory that Foshag is working on." The present paper is a report on the facts observed at the depo its near Kramer, and some general observations on the geological relations noted, which, unfortunately, still form only a very incomplete record. The intimate association of deposits of colemanite and ulexite in California and Nevada with certain volcanic rocks affords a strong pre-

Jan 1, 1926

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the-indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer, or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made . . .

Jan 1, 1943

Contents A-Metal Mining B-Minerals Beneficiation F-Coal

Jan 11, 1951

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with' foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel con-stitutes a large volume of tonnage in daily use. There is a fairly prev-alent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applica-tions sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat treating, particularly carburizing, is performed on this grade.

Jan 1, 1935

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By Rossiter W. Raymond

The extent to which the divining-rod is still used in this country for the detection of hidden treasure, mineral veins, or springs, is ' much greater than educated persons would be likely to suppose. For many years wells have frequently been located by its aid in New England, where the belief is widely extended among the farmers that in the hands of peculiarly gifted persons this instrument possesses special virtue. Large numbers of the oil wells of Pennsylvania

Jan 1, 1883

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,' Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer's suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By M. Muskat, R. D. Wyckoff

The general problem of the simultaneous movement of water and oil in a connected sand is of considerable practical interest from two points of view. First, there is the situation usually described as "edge-water encroachment." Here the water in the sands contiguous to and flanking the oil sand begins to enter the latter as the oil is removed and the reservoir pressure declines. The physical questions involved concern an understanding of the mechanism of the advance of the water and its control, so as to aid the oil recovery rather than to hinder it. In so far as the entry of the water into the oil sand means at least the partial replacement of the oil from the region of the encroachment by the advancing water, it is quite appropriate to consider this type of situation as one of natural water-flooding. For the present discussion, however, we are primarily interested in the problem of artificial flooding. Here the water is deliberately injected into the oil sand with the intention of displacing the oil and removing it through prearranged output wells. For the practical development of such a procedure rather large areas are included in the flooding program and the injection and output wells are arranged in regular patterns or networks, which are felt to be most favorable for a high oil recovery. Although remarkable success has already been obtained in such flooding programs, especially in the Bradford field of Pennsylvania, essentially by the application of the lessons of practical engineering experience, a more thorough physical analysis of the problem appeared to offer promise of leading to results of some interest and value. Another phase of the problem, which stimulated both the experimental and mathematical analysis, is that it is susceptible in large measure to empirical field tests. It, is in itself but an example and illustration of the general theory of the flow of dead (gas-free) liquids through porous media, in which the authors have been interested for the last several years. From the point of view of its applicability to actual petroleum technology problems, however, water-flooding is a particularly favorable

Jan 1, 1934

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By Samuel G. Lasky

What the evidence prevails upon the mind to believe, depends upon the mind as well as upon the evidence. M. L. IN a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of MINING AND METALLURGY, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose, we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step-the decision whether exploration should be undertaken-rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. PHILOSOPHY OF APPRAISAL If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. How then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects `have already been ex-

Jan 1, 1947

By Jules E. Jenkins

IN the past quarter century the seismograph has played an increasingly important role in evaluating vibratory effects transmitted to adjacent communities by industrial blasting operations. In this period research has advanced through two major phases—from falling pin seismometers to three-component recording seismographs. The initial phase of this research is now regarded as the era of recording, during which the seismograph merely recorded occasional events. It has emerged from this stage into the era of control and analysis and in this later period has been recognized as a full-fledged industrial tool. Although the falling pin machines of earlier years indicated probable amplitudes of industrial blasting vibrations, they gave no reliable measure of such displacements, nor did they provide essential information concerning direction or frequency of motion. The first contribution of the three-component recording seismograph was the weight-for-distance formula developed by the U. S. Bureau of Mines. This empirical formula enabled users of commercial explosives to determine beforehand the probable vibratory effects of a blast when the weight of the explosives charge and the distance from the shot point were known. This formula has withstood the test of time and is still applicable for blasts detonated by instantaneous methods. The second major contribution of the three-component recording seismograph followed the introduction in 1945 of short period or millisecond delay detonation. This might be described as a two-stage contribution, the first of which revealed a 50 pct reduction in the vibration magnitude when millisecond detonation was used rather than instantaneous discharge. This second part of this double contribution led to the discovery of the vibration dip phenomena, see Fig. 1. In Fig. 1 the horizontal coordinates indicate the displacements amplitude in inches, and the vertical coordinates, the explosive weight in pounds. The top curve is that of the U. S. Bureau of Mines for instantaneous detonation. Its curvature conforms to the two-thirds power of the explosive weight as provided in the weight-for-distance formula; hence the vibratory effects increase in proportion to an increase in the explosive charge. If the other curves shown below are temporarily disregarded, it may be considered that the entire area below this top curve represents both useful and waste energy. As mentioned previously, when millisecond delay detonation was first investigated it was found that in general the U. S. Bureau of Mines curve could be decreased by about 50 pct, or to the position of the middle curve. At the outset it was assumed that this curve would likewise increase in some proportion to the explosive charge, as did the top curve, that is, the curve would indicate a continuous upswing. As seismographic data accumulated this assumption was found to be erroneous in part. It was discovered that

Jan 1, 1957