Search Documents

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded&apos; that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,&apos; can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970

By Larry Dale

An approach for predicting the development of mineral resources on public lands has been developed as an aid to resource agencies. It consists of new techniques for evaluating the economic potential of the resource, the uncertainty about mine cost estimates, and the uncertainty about the occurrance of mineral deposits. New mineral sup- plies from inferred and hypothetical resources can be predicted by using these techniques. A case study illustrates their application in predicting development of copper resources in western Montana.

Jan 1, 1982

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought &apos;and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By T. F. Witherbee

Discussion of Mr. Baker&apos;s paper, read at the Lake Superior Meeting, September, 1904. MR. T. F. WITHERBEE, Durango, Mexico (communication to the Secretary*) : Mr. Baker&apos;s paper is very instructive in that it shows how furnace-derangements sometimes originate from apparently slight causes. In 1896 a similar burning through of the lining occurred at the Mayville furnace of the Northwestern Iron Co., Mayville, Wis., in exactly 38 days from the time the furnace was blown in. At that time I attributed it to the fact that the bell was carried several inches to the front side of the furnace, the length of the versed side of the arc described by the lever, thus dumping a little more of the charge on the back side, which made the front side of the furnace-charge more open and consequently increased the circulation of the furnace gases through it. After reading Mr. Baker&apos;s description, I believe that possibly a little more ore was charged on the back side of the hopper, due to the fact that it was nearest to the elevator. This unequal charging, however, was unconsciously done, as the fillers were both honest and faithful. The illustration of the burned lining of Furnace No. 1, given in Fig. - of Mr. Baker&apos;s paper answers very well for the Mayville furnace. It shows that in both cases the destruction of the lining was largely due to faulty construction, in that there were no cooling-plates in the angle of the bosh and in one or two courses of brick above it, where I believe they are-more in demand than anywhere else in the furnace. The presence of these cooling-plates at the angle of the bosh would have obliged the current of the hot gases to turn the corner and would have prevented them from following the angle of the bosh com¬pletely through the lining and shell.

Mar 1, 1905

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By E. W. Pehrson, J. W. Furness

THE method of presentation in the accompanying charts is based upon the well-known formula: production plus imports minus exports equals apparent consumption. Thus for each area for which data are shown there are two columns of equal height, one representing production plus imports, the other apparent consumption plus exports. Usually no account has been taken of increases or decreases in stocks. All columns and flow lines are drawn to a linear scale which is supplemented by figures showing the actual quantities represented. Owing to the small area occupied by the European countries on the world map it was impossible to show the details of the trade of the individual countries. All of Europe (except Russia), therefore, is shown as a single unit. However, statistics of production and consumption indicated elsewhere on the charts show the degree of self-sufficiency enjoyed by the major European powers.

Jan 1, 1936

The Sub-committee on Safety of the Industrial Organization Com-mittee of the Institute has been asked to cooperate with the National Safety Council, and has made certain recommendations to the Board of Directors of the Institute regarding ways and means of bringing about this cooperation. The National Safety Council has been in existence seven years. Its inception was at a meeting of the American Iron and Steel Electrical Engineers held in Milwaukee in 1912. The first annual congress was held in New York City in October, 1913, at which time the Council was definitely organized. Its membership now consists of nearly four thousand members, representing industrial plants, railroads, public utility companies, insurance companies, state labor commissions, Chambers of Commerce, manufacturers&apos; organizations, etc. These members are in all states of the Union and in eleven foreign countries, and through them the National Safety Council reaches more than six million workers.

Jan 7, 1919

By Oliver S. North

Reserves of perlite rock in the western section of the United States are immense. A geological report prepared for the Union Pacific RR showed proved tonnage of over 400 million tons in southern Nevada alone. Yet the perlite industry is not large, and most of the mines are relatively small. There are indications that perlite processing, thus far largely in the hands of relatively small com¬panies, is becoming concentrated in a few large companies. For economic reasons the bulk of perlite sold in crude form has come from three or four pro¬ducers, although many individual operators have sold small quantities to limited lists of purchasers. Perlite is one of ultra-lightweight aggregates. Owing to its outstanding qualities as an aggregate, variety of uses, and ultimate economy of use, it has enjoyed considerable popularity in this country in recent years. Marked foreign interest also has been evinced in this material.

Jan 2, 1955

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

By T. B. Counselman, T. B.

Continuous countercurrent decantation calculations have always been a headache to the cyanide man (and the chemical engineer) because of the simultaneous equations involved. These are tedious to solve, and there is considerable opportunity for mathematical error. This paper presents a shortcut method for making these calculations, which has been in successful use for twenty years by the author, and which is particularly valuable in selecting the best of several possible flowsheets, or evaluating the effect of various assumptions.

Jan 1, 1950

By R. J. Woody

DESIGN of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 7, 1958

By AIME AIME

IN many countries the lack of liquid petroleum supplies has centered interest upon the hydrogenation of coal and coal tars for the preparation of motor fuel. In the United States, hydrogenation has been of greater interest for grading up low-value petroleum fractions to the more valuable volatile fuels and for the preparation of a variety of premium products, including aviation gasolines, solvents, Diesel fuels, and lubricating oils. Chemically, the basic reason for this process is that, as shown in Table 1, the ratio of hydrogen to carbon (H/C ratio) in available raw materials is quite different from that characterizing the products sought.

Jan 1, 1936

The President&apos;s Prizes, which consist of $30 and $20, were established for the best essays on some subject related to Mining, Economic Geology, or Metallurgy by a Junior Associate or a Member of an Affiliated Student Society of the Institute. In making the awards, special weight will be given to originality in investigation and treatment and to literary merit. As a general rule, the essays should not be less than 3000 nor more than 10,000 words.

Jan 1, 1923

By T. B. Counselman

Continuous countercurrent decantation calculations have always been a headache to the cyanide man (and the chemical engineer) because of the simultaneous equations involved. These are tedious to solve, and there is considerable opportunity for mathematical error. This paper presents a shortcut method for making these calculations, which has been in successful use for twenty years by the author, and which is particularly valuable in selecting the best of several possible flowsheets, or evaluating the effect of various assumptions.

Jan 2, 1950

By F. F. Lines

IT is not the intention of the writer to enter into a discussion of the relative merits of the duplex process as compared with the straight scrap and pig iron process, working under the same conditions, but rather to present in a general way several modifications of the former process, and then describe the method adopted by the Maryland Steel Co., as best suited to local conditions, and also to meet the metallurgical problem presented in the removal from the iron of an unusual constituent-chromium. The principal factors to be considered in deciding whether or not duplexing should be employed are: (1) Chemical constituents of pig iron. (2) Variety and quantity of steel to be produced. (3) Relative cost of pig iron and scrap. (4) Regularity of operation. (5) Capital to be invested. (6) An existing Bessemer plant. Having decided to adopt the duplex process, several combinations may be used, viz.: (1) Acid-lined converter with basic open hearth. (2) Acid-lined converter with electric furnace. (3) Basic-lined converter with basic open hearth. (4) Basic-lined converter with electric furnace. (5) Basic open hearth with electric furnace. The combination of an acid-lined converter with a basic open-hearth furnace is the one most commonly employed, and as it is the one best adapted to the conditions encountered at the plant of the Maryland Steel Co., we will briefly outline the advantages and disadvantages of the different methods of working.

Jan 4, 1915