Search Documents

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By Omar. M. Arafat, Edgar Pérez, Kyle. M. Bartholomew, Robert. E. McIvor

The “circulating load” confounds understanding of ball milling circuits. Conflicting opinions exist as to its role. Should it be high, or low? Why does it even exist? It is commonly accepted in the plant as a given, the outcome of largely unknown factors. As such, it may often go unmeasured or even ignored. This paper describes the importance of the circulating load in wet ball milling circuits. It is characterized not only in terms of solids mass flow (or ratio of mass flows), but also by its other key physical characteristic, its size distribution. Its effect on grinding circuit performance is explained. The equipment application design steps to achieve a desired circulating load, in terms of both its mass flow and size distribution, are described. Finally, its pivotal role in grind control is specified. Our goal is for the reader to come away with a fresh understanding of the role of the circulating load in wet ball milling circuits, including how and why it should be measured and managed.

Feb 22, 2026

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By M. Peters, P. Schmäh

The development of renewable energies and a sustainable power grid are the challenges for future energy supply. Underground cables will replace the vulnerable overhead lines, because of their safety benefits. Due to the public environmental awareness, smart tunnelling and trenchless solutions are required for inner-city and cross-country installations of underground cables, as well as for crossings and the landfall sections to connect offshore wind farms to the transmission grid. Methods from the tunnelling and pipeline industry provide a high flexibility in the planning of alignments, including versatile tunnel concepts and the installation of protective pipes with E-Power Pipe and Direct Pipe.

Jun 13, 2023

By Guy D. Bruno

Through the remainder of this century, world consumption of fluorine per ton of primary aluminum produced will continue to be substantially reduced. Growth of the primary industry will offset some of the unit consumption, but demand for new fluorine sources will decline sharply. Continued application of dry fume scrubbing systems will be the most significant factor in reducing demand.

Jan 1, 1978

By J. A. Luppens

Five years ago, Phillips Coal Company decided replacing mainframe/workstation programs with a new package of PC software was clearly the best solution for computer reserve modelling. The system chosen was actually three programs distinguished by their power, cost, flexibility and integration, and ease of learning and use. Phase I involves the use of the "StratiFact" program for borehole data management and seam correlation. This phase is probably the most neglected, yet critical aspect of reserve evaluation. Phase II employs the "PC/Cores" package for modelling and volumetrics. Phase m is "PC-Cut" which provides mine planning tools including an automated cut generator.

Jan 1, 1996

By F. Schreiter

"One method to increase the exploitation rate of a mine is the use of backfill with residual materials in exploited areas. The backfilled material is meant to support both, the walls of galleries and pillars as well as the roof of mining openings. With increasing depth, the exploitation rate diminishes fast, thus the application of backfill in order to change the layout of the mine is crucial for economic success. In result of using backfill, it is possible to change the layout of the working area with a higher ratio to excavated areas and less area occupied by pillars. Thus it is possible to boost the output of a mine by using backfill. Setting the criteria for the selection of the best possible materials and whose improvement, it is useful to know about their qualities and handicaps. The Mining Department at TU Bergakademie Freiberg is analyzing the parameters of residues from different processing methods, accrued in plants of different potash mines and blending different residues for optimization of material attributes. These were significantly characterized by basically parameters like the size and the distribution of different diameters of the grain material. INTRODUCTION The chair for underground mining methods at TU Bergakademie Freiberg is tasked with the sufficient and sustainable supply of economics with raw materials. The steady high demand, the rising prices and the finiteness of the deposits are reasons for the need of an optimized economic utilization of natural deposits, a continuous improvement of mining technics and technology. From an ecological and economical position the best possible utilization of the resources has to be achieved. Many mining operations are by reasons of the deposit not able to haul valuable minerals only, they have to haul a mixture of valuable minerals and waste rock. This hauled combination is given into the processing plant for separation and enrichment of the valuable mineral. The residuals of the processing are commonly dumped to a waste rock pile. For minimizing the size of such a waste rock pile and also minimizing the ecological footprint of a mining operation the only way is minimizing the quantity of accruing waste rock material. Both, optimization of economic utilization and also minimization of waste rock dumps can be realized in one by backfill with processing waste rock material in mined out areas. Especially in mines, mined by room and pillar method, smaller dimension of the pillars are sufficient for safety and stability. By the way less valuable minerals have to be leaved back in the mine and the mine outcome is increasing."

Jan 1, 2015

By Patzen Wu

The Hai-Shan No. 1 Coal Mine, located in northern Taiwan, is one of the typical coal mines on the island which, limited by natural condition, are mostly small in scale. With the advancing longwall method, the mine is now winning a seam, 80 cm thick, at a 32° dip, with a working depth of 824 m below surface. The annual output is about 50,000 mt of clean coal. At the working gallery, the virgin rock temperature may go up to 46°C, difficult to be brought dam to n acceptable level: because .of the tropical climate with high intake temperature and high humidity. Besides, at this depth, the intake air that goes down the long inclined shaft generates considerable heat due to autocompression. The mine is ventilated by a set of axial-flow fan with 38 m3/S of intake air at 2.2 KPA WG. With this volume of air, the temperature at the working-face is usually above 30°C WB. Appreciable lowering of the temperature is not expected even with an increased volume of ventilated air. For this reason, decision has. been made to try the installation of a pilot underground refrigeration unit near. the lowest gate road to cool the intake. air. from 32°C WB to 28°C WB which seems acceptable to on-the-spot workers exerting heavy physical labor. The experimental unit is designed for carrying away a total heat load of 90 Kw. The capacity of the unit is 200 Kw. The unit consists of a compressor, an evaporator, a condensor and a motor. The heat rejection is done in a cooling tower. Chilled water is circulated from the evaporator to the cooler by insulated pipes. The cooler consists of 90 Kw-coils with two fans and forces air by flexible ducting onto the working face. This paper examines mainly the effect of this additional reduction of working temperature, on working efficiency of the workers. Another aspect of this experiment is to evaluate the overall economy of underground refrigeration in small-sized coal mines under tropical condition. The success of such an experiment may lead to wider application of refrigeration to render many of the deeper mines economically workable.

Jan 1, 1980

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By D. J. Boron, R. Kollrack

Introduction The US has the largest total (364 Gt, or 401 billion st) and recoverable (182 Gt, or 201 billion st) coal reserves in the world (Steam/Its Generation and Use, 1978). However, progressive coal use in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. Since the promulgation of the Environmental Protection Agency (EPA) New Source Performance Standards (NSPS), it has become apparent that all US coals will require sulfur removal to comply with the new sulfur dioxide emission levels. If more stringent emission standards are imposed, through pending acid rain legislation or amendments to the Clean Air Act, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the development of new and advanced coal cleaning technologies to continue and promote the use of coal. Table 1 summarizes the EPA NSPS for sulfur dioxide emissions. Fortunately, the basis for determining sulfur dioxide removal is the Btu and total sulfur content of the run-of-mine coal. Thus, credit is given for any sulfur removed before combustion, e.g., through physical coal cleaning. Unfortunately, physical coal cleaning alone may be unable to produce a compliance coal with respect to the EPA NSPS. Therefore, all industrial and utility coal-fired boilers will require post combustion gas cleanup, e.g., flue gas desulfurization (FGD), to comply with the new regulations. Table 1 - EPA NSPS for SO2 Emission Category SO2 Content of ROM Coal SO2 Reduction Required 1 0-2 Ib/M Btu 70 2 2-6 Ib/M Btu To 0.6 Ib/M Btu (70% to 90%) 3 6-12 Ib/M Btu 90% 4 12 Ib/M Btu To 1.2 Ib/M Btu Alternatives to post combustion gas cleanup, such as staged combustion, lime and coal injection, fluidized-bed combustion, and chemical coal cleaning, are currently under development. Of these, chemical coal cleaning offers the advantages of providing (1) high quality fuel for combustion (low sulfur and ash, high Btu, and attenuated product variability); (2) a solid fuel product for use in retrofitted gas and oil boilers; and (3) a solid fuel product with multiple end uses, e.g., internal combustion engines, carbon electrodes, coke, or chemical feedstock. Gravimelt process In the Gravimelt process, 1.4 mm x 0 (14 mesh x 0), physically beneficiated coal of about 5% moisture is fed into a 3401 to 3901 C (644 ° to 734 ° F) molten bath of sodium hydroxide and potassium hydroxide. Organic and pyritic sulfur and most of the mineral matter in coal react with and are dissolved in a molten mixture of potassium hydroxide and sodium hydroxide. The reacted coal sulfur is converted to alkali sulfides and polysulfides, whereas the mineral matter is apparently converted to alkali-aluminum silicates and other byproducts that are water and acid soluble. Coal residence time is 60 to 240 minutes. The sodium hydroxide to potassium hydroxide ratio is about 9:1. The total hydroxide-to-coal ratio is no less than 10:1. The specific gravity of the caustic melt is about 1.8 g/cm3 . Thus, coal is buoyant in the bath, and insoluble mineral matter with density greater than 1.8 g/cm3 would sink. Reacted coal is first water-washed with an equal weight volume of water in a countercurrent mode of operation. The coal is filtered and the filtrate sent for regeneration. The coal is then acid-washed in 10% sulfuric acid. The acid-water/coal mixture is filtered to recover the final coal product, and the filtrate treated with lime to precipitate dissolved mineral matter. The precipitate is filtered from the mixture and discarded. The water is recycled to the plant. Filtrate from water-washing is treated to remove sodium sulfide. The sodium sulfide is chemically treated to produce hydrogen sulfide, calcium car¬bonate, sodium hydroxide, and other products. The hydrogen sulfide is treated to produce sulfuric acid for the acid-washing step. The calcium carbonate is treated further or discarded, and the sodium hydroxide is concentrated by evaporation and recycled to the reactor. The Gravimelt process is currently at the bench-scale stage of development. A 0.9-kg (2-lb) continuous reactor is in operation with a continuous water- and acid-washing section adjacent. The regeneration section is not developed to a meaningful extent, although key reactions have been tested in the laboratory. Process conditions, product recovery efficiencies, etc., however, have not been determined adequately and continuous regeneration operation has not been attempted. Work is now in progress to develop each section to a continuous bench-scale operation in processing coal at 9.1 kg/h (20 lb per hr). Microwave process The carbon and hydrogen in coal are relatively transparent to microwave radiation. However, water, caustic, pyrite, and other mineral matter components are strong conductors of microwave radiation energy at the proper frequency. As a result, selective heating of the noncarbonaceous materials occurs that enables the chemical reaction of sulfur and ash with caustic. Although very high temperatures may result from

Jan 1, 1987

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By William Gleason

The Dulles Corridor Metrorail Project is a $3-billion project that will link Dulles International Airport with the downtown center of Washington D.C. by way of a single seat train ride. The project is mostly above ground, but it does include two short, yet complex, tunnels through the area of Tyson?s Corner. The project is being completed in two phases. The Dulles Transit Partners (DTP), led by Bechtel, was awarded the first phase, a $1.6-bil-lion phase that includes 17 km (11 miles) of track with five stations. At Tyson?s Corner, the project includes twin 730-m- (2,400-ft-) long, 6-m- (20-ft-) diameter tunnels. Bechtel is self-performing construction for the $1.6-billion design-build job. Gall Zeidler Consultants was hired by DTP as designer for the NATM tunnel portion of Phase 1, and Beton-und-Monierbau was hired as tunnel subcontractor. Tyson?s Corner is an affluent and congested area that sits 152 m (500 ft) above sea level. To get through the area, it was decided that tunnels would be the best option with the least amount of disturbance to the surrounding areas. However, with extremely shallow groundcover above some points as well as soft soil throughout, the tunnels are also the most complex aspect of Phase 1. About 213 m (700 ft) was constructed utilizing the cut-and-cover method. The remaining 518 m (1,700 ft) is being constructed using the New Austrian Tunneling Method, which integrates the principles of the behavior of rock and soil masses under load, and monitoring the performance of underground construction during construction. ?The tunnel only falls 2 m (7 ft) from one end to the other and we pass through two soil conditions, they are both soft ground,? said Dominic Cerulli, tunnel task manager for Bechtel. ?Soft ground is very tricky because you have to close the ring in a timely manner to minimize settlements at the surface. If you don?t close the ring quickly to achieve a round structure that?s good in compression, the tunnel could start necking and squatting and the ground above it will settle. We are under major roadways, so excessive settlement would be a bad thing.?

Jan 1, 2011

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By H. A. Zollinger

The Hallmark Distribution Center is one of the most sophisticated material handling and order filling facilities in the world. The 53 million cubic foot facility houses an ultra-modern, computer- monitored distribution complex that handles as many as 1/4 million orders per day. The Distribution Center replaces 16 leased buildings scattered through- out metropolitan Kansas City and, in addition, re-leased 4 floors in mid-town Kansas City needed for creative and administrative expansion. This new facility is the nerve center for distribution of Hallmark products in United States and Latin America. The size and gross numbers of all parts of the system is a significant accomplishment, but the purpose of this paper is to explain the technical advancements in the state-of-the-art of material handling and controls. The system iteself is made up of seven sub-systems including receiving, warehousing, picking rack stocking, towline, order filling, order sorting, and shipping. Significant techniques were used in each of these areas as well as technical advancements in the state-of-the- art. The most significant points are in 4 of the areas and are discussed in this paper.

Jan 1, 1973

By Kristin Hemlein

Mining project development, permitting, environmental regulatory and compliance issues in Uzbekistan and the CIS are every bit as complex as those in the western world. The vast array of environmental permitting, monitoring and reporting regulations for mine project development and operation in the CIS are based on existing Soviet environmental regulations and policies which have remained in place after these countries gained independence from the former Soviet Union. The approach to mine project permitting in the CIS differs from the western world. Similar pre- feasibility, baseline data collection, and environmental monitoring requirements allow the project proponent to coordinate preparation and submission of documentation to support project permitting for Uzbek regulatory requirements with environmental requirements imposed by financial institutions and western environmental compliance structures. Implementation of generally accepted western environmental best management controls and monitoring into mine design, construction, and operation will not, however, ensure automatic compliance with Uzbek environmental regulations. Uzbek environmental compliance requirements that differ from western requirements include: 1) development and maintenance of an environmental database constructed specifically to address annual, biannual and quarterly statistical reporting requirements for emissions of "environmental pollutants" from the facility into air, surface water, ground water and soil; 2) preparation and submittal of specific permits for water utilization, hazardous waste storage and disposal, landfill construction and operation, and stack emissions inventories; and 3) procurement of approvals from the Uzbekistan State Committee for Nature Protection (generally analogous to the US Environmental Protection Agency). This paper outlines and summarizes the regulatory requirements for mine site permitting and the procedures for environmental monitoring and reporting during mining operation in Uzbekistan and the CIS.

Jan 1, 1997

By William A. Faust

At Gold Fields' Chimney Creek Mine, major reviews of the reclamation and closure plans are done concurrently with the annual mine planning required for budget preparation. This review includes identifying and scheduling reclamation work that can be done within the next few years and development of associated costs. Longer term mine, leach pad and waste dump development are examined to take advantage of any design changes that can reduce ongoing reclamation or closure requirements and reduce costs. The success and cost effectiveness of past efforts are continually evaluated to determine the best methods for reclamation.

Jan 1, 1992