Search Documents

By M. Z. Emad, N. Abbas, Y. Majeed

Room-and-pillar mining is commonly employed for the extraction of rock salt in undergroundmines. Pillar stress is a major concern in these mines as it is directly related to stability and mineralrecovery. In this study a flat jack method was used to measure pillar stresses in three undergroundrock salt mines in Pakistan. The field work included determination of in-situ stress, in-situ elastic modulus, recording of field variables (pillar length and width, height and width of opening, opening width to height ratio, extraction ratio, and overburden height) and collection of salt block samples. The geomechanical properties of rock salt (uniaxial compressive strength, Young’s modulus, Brazilian tensile strength, and density) were also determined to estimate overburden stress, pillar strength, and factor of safety (both estimated and actual). It was found that the measured pillar stresses are proportional to the overburden stress values, with their magnitude ranging from 6.05 MPa to 11.97 Mpa, and the pillars were found to be stable. Regression analysis was performed to develop statistical models for in-situ stress and in-situ elastic modulus. Finally a quick guideline chart was developed to determine the suitable length of pillar for a given span and required level of safety.

Jun 5, 2023

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical for these processes is that the amount of slag is quite high. The role of slag for the process is thus very essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2based with minor contents of CaO and CrOx. Slags in FeMn process are principally similar originating from silicate minerals but can have quite a large composition range depending on the manganese ore and its gangue minerals. Characteristic for FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOxin slag are not only divalent oxides but also containing some higher valent of Cr3+ and Mn3+, respectively. In FeMn production conditions the slag consists mainlyMn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexists in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. Thermodynamics of slags in ferroalloys production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties.

Jan 1, 2004

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By N September, R Abate

Bateman Modular (previously Van Eck and Lurie) has been building and supplying the mining industry with modular DMS plants for the last 30 years. These DMS modules range in capacity from 1 tph to 200 tph. The most popular unit produced by Bateman Modular over the years has been the 50 tph module. Development In the last 7 years a need has arisen from the industry to provide Modular DMS plants that can treat higher tonnages (150 to 200 tph). The first DMS provided to the mining industry based on the modular concept was a 150 tph DMS Module to MIBA in the DRC. Since then Bateman Modular has provided some 14 Mega DMS modules over the last 7 years with the latest two orders from Debswana (Damtshaa double up project) and Namdeb. Ever since the first Mega Module was supplied Bateman Modular has been improving the Modules. Implementation The modules can be supplied in different configurations so as to improve the overall availability of the plant. Two off 150 tph DMS modules were supplied for a Transhex operation. This allowed the client to still operate one DMS module while maintenance is being performed on the other DMS module. The client also has the option of choosing a single module. Successes The following list of projects provides the base for the success of the Mega Modules.

Jan 1, 2006

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By E. Matinde

Poor phase separation and fine dissemination of the desired components within congruous slag phases are key challenges limiting the recoverability of values from slags by conventional beneficiation methods. Slag microstructure conditioning is a pragmatic approach to increasing themvalue-in-use of discard slags, especially when integrated with the broader smelter infrastructure. Although not yet tested on oxide slag systems, this paper explores the potential application of magnetohydrodynamic principles to the crystallization behaviour of bulk slags. Integrating the slag microstructure conditioning infrastructure to the existing smelter infrastructure is key to unlocking the economic value of slags because it is most economic to condition the properties of molten slag directly after tapping. A new business model that integrates smelting units to transversalmeconomic activities, such as cement production and suppliers of construction aggregates, canmsignificantly increase the circularity of metallurgical slags.

Oct 9, 2024

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By M. -O. Suk, S. -K. Jo, S. -C. Shim, J. T. Kim, S. -H. Kim, C. -W. Seo, J. -S. Kim

An equilibrium study was carried out at 1873 K to ascertain the effect of carbon in CaO-SiO2-Al2O3-MgO-MnO-FetO slag systems on their FetO and MnO activity coefficients, representing the slag?s thermodynamic potential for steel reoxidation. Both ?FetOand ?MnO showed not only a sharp increment, but also a simultaneous slow decrement by increasing carbon content in slag, suggesting opposite roles of the carbon according to its stable forms. XPS (X-ray photoelectron spectroscopy) was introduced to clarify the stable forms of carbon in slag. XPS results prove that carbon dissolves in slag as carbonate, and carbide ions under oxidizing and reducing atmospheres, respectively. It was concluded that carbonate ions increase ?FetOand ?MnO, and that carbide decreases them. This paper suggests an application method of the present results to actual ladle refining processes, in order to enhance steel cleanliness without decreasing (FetO + MnO) content in slag. Keywords: carbon, slag, activity coefficient, FetO, MnO, carbonate, carbide, XPS, reoxidation, cleanliness

Jan 1, 2004

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

By J. L. Fuentes-Cantillana, J. B. Solar Menéndez, A. O. Cámara

The Principality of Asturias is a region situated in Northern Spain with two centuries of tradition in underground coal mining. In addition, its uneven relief has obliged the construction of a great number of tunnels both for railways and roads. Basing on this experience and an ever increasing need to improve on safety, the Barredo Foundation dependent on the Regional Government and the University, provides and manages a Centre for Research of Fires and Ventilation in Tunnels. The Centre has as its most important infrastructure, a tunnel 540 m long, 9,5 m wide and 8,0 m high at centre. This section coupled with ventilation equipment allows the simulation of risk conditions at real scale, which is achieved by modifying the geometry of the section and through two powerful stations situated one at either en of the tunnel. In addition, the Centre houses two test benches for fans and electrical motors at high temperatures. One bench with a re-circulation conduit is the most appropriate for tests in Transversal and Semi-transversal type of installations. The other, is for the testing of electrical motors or fans which operate in zones where the surrounding temperature is high. In this Centre, training has also been developed for Fire Fighters and Civilian Protection Personnel who have to work in fire and smoke rescue conditions in underground structures. Testing conducted at real scale enables this formation and also to improve different computer programmes in the field of Fires and Ventilation.

Jan 1, 2003

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003