Search Documents

By P. K. Van Manen

Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province in South Africa. A single 168 MVA six-in-line rectangular furnace smelts dry concentrates containing platinum group metals (PGMs). Furnace energy consumption since commissioning is presented, showing that energy efficiency improves as capacity utilization increases. An energy balance for the furnace is outlined, indicating the measured or calculated energy losses from the hearth and side-wall cooling, the copper coolers, the upper furnace walls and roof, and the energy losses in off-gas, matte, and slag. From the energy balance, the potential to improve energy efficiency by controlling the slag temperature, the slag level, and the off-gas volume is derived. Furthermore, the impact on the energy balance of different concentrate types is discussed, as well as the potential impact of replacing all upper waffle coolers by plate cooler panels.

Jan 1, 2009

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

By D. K. Weatherley, T. P. Oladele, L. B. Bbosa

Comminution is a critical stage of mineral processing which aims to reduce the size of ore particles through breakage, consequently increasing the likelihood of liberation of valuable minerals. Several factors, such as pre-existing cracks, mineralogical composition and particle size, are known to affect ore breakage behaviour. While investigating the contributing role of each factor is essential to improve understanding of breakage, isolating individual factors by experiment is typically impractical. Numerical techniques such as the Bonded Particle Model-Discrete Element Method (BPM-DEM) have been developed as a means of studying closely controlled breakage conditions. This study evaluates this technique in modelling the effect of pre-existing cracks breakage behaviour for synthetic ore specimens during impact breakage in a short impact load cell (SILC). Synthetic ore was modelled as a collection of discrete entities connected by brittle-elastic beams. Model parameters were calibrated against macroscopic material properties of a conventional homogenous synthetic ore. The extent of pre-existing cracks within specimens was prescribed by varying discontinuities between the connecting entities. An approach with the insertion of seed points was used to model the mineralogy of the specimens. Results showed that pre-existing cracks resulted in a decrease in the fracture force as the crack density increased. Additionally, the irregularity of fracture patterns within rock specimens after impact became more apparent as the crack density increased. The findings were used to emphasise some of the attributable causes of the variation observed between ore hardness characterisation tests and in situ ore behaviour. Keywords: Element Method; Bonded Particle Model, synthetic rock sample; rock fracture, preexisting cracks

Jan 1, 2020

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

A modified germanium recovery process in conventional zinc metallurgy, based on the understanding that ferric hydroxide has strong ability to coprecipitate germanium element, was presented. The relaxed lab-scale experiments were conducted to evaluate its technological feasibility. The experimental results obtained show the new process has great competitive advantage over the conventional one.

Jan 1, 2008

By L. A. Sandham

Environmental impact assessment (EIA) in South Africa is administered by the Department of Minerals and Energy (DME) for the mining industry, and the Department of Environmental Affairs and Tourism (DEAT) for all other sectors. Thus far, EIA research has focused on the process under the auspices of DEAT but none has focused on the EIA process that has been mandatory in the South African mining industry since 2004. Using the Lee and Colley(Lee et al.13) review package as a basis, a review model specifically tailored to the needs of the mining industry was applied to review the quality of a sample of 20 environmental impact reports (EIRs)approved by the DME. Results reveal that 85% of the EIRs are of a satisfactory quality. Presentational and descriptive components generally achieved higher quality grades than the analytical components such as impact magnitude and alternatives. The results show that in spite of some areas of weakness, and in spite of being conducted in terms of different legislation, EIR quality in the mining sectors appears to conform to the overall standard of quality of EIRs in other sectors in South Africa, and is also on a par with quality abroad. Hence, despite the criticism that DME is usurping the role of DEAT, it is concluded that EIRs of comparable standard are being produced, and that the quality of EIRs in the mining sector do not provide supporting evidence for this criticism. However, EIR quality is only a single aspect of EIA effectiveness, others including action and implementation of EIA proposals and mitigation measures.

Jan 1, 2008

One of the key issues facing gold producers is the management of cyanide and the implementation of the International Cyanide Management Code. Many operations now use cyanide destruction processes to ensure that the material being discharged to the tailings dam is compliant with regulatory requirements and the International Cyanide Management Code. One of the problems for operations is the quantification of both cyanide species and their reaction products throughout the leach and destruction circuits. Therefore methods have been developed utilizing high performance liquid chromatography (HPLC) to measure free cyanide, cyanide complexes of metals such as copper and iron, and other species formed from reactions in leaching and cyanide destruction, including cyanate, thiocyanate, and sulphur species (eg. sulphite, thiosulphate and sulphate). This enables a complete mass balance for cyanide and sulphur in both leaching and cyanide destruction. This paper outlines the methodology which has been developed and discusses the application of these methods in the fundamental research currently being conducted on the impact of sulphide minerals in cyanidation and cyanide destruction chemistry.

Jan 1, 2009

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific's (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By M. Bailey-McEwan

The application of refrigeration on deep South African gold mines is mostly achieved through the medium of chilled water which is produced in central installations either on surface or underground. The amount of refrigeration has been increasing rapidly over recent years, and the total installed capacity on all gold mines now exceeds 1000 MW(R), with annual running costs exceeding R100 million for electricity alone. Hence, there are strong incentives to design such installations for optimal cost-effectiveness. The duty required of these installations varies considerably, owing to daily and seasonal climatic changes and the varying nature of the water demand. It has long been recognized that a computer program to predict installation performance as a whole under any given conditions would be highly desirable. An interactive computer program, CHILLER, is described which enables the user to build an installation, consisting of any configuration of cooling towers, water storage reservoirs and packaged water chilling machines. Externally-dictated conditions such as the weather and chilled water demand must be specified, and all quantities under control of the installation, including internal water flow rates and compressor capacity regulators, must be set. The time-varying performance of the installation can then be simulated. Examples are given of the application of the program in the design of a new installation, and in evaluating the effect of any modifications to existing installations.

Jan 1, 1987

By P. Lloyd

Perceptions of disaster caused by burning fossil fuels have reached such a pitch that they seriously threaten the very future of the industry. Coal is a dirty word. A leader in Business Day(January 192009) claimed ?There is no disputing that renewable and non-polluting energy sources are preferable to the country?the true cost of so-called cheap coal-fired power stations is neither reflected nor accounted for by Eskom?the true and immediate but unacknowledged cost of continued coal mining is apparent in the catastrophic level of acidification from mining runoff of all significant natural water resources in the country?and their waters have been rendered unfit for human consumption. Air quality is in a similar state with?increases in pulmonary disease causing workforce absenteeism and compromised childhood development, among many other health problems recorded in areas polluted by coal mining.? The upshot is that our latest coal-fired power station, Kusile, is being required to use flue gas desulphurization. The costs are considerable, and the benefits minimal. Meanwhile, exports are being threatened by EU directives and an assumption that South African coal gives off excessive quantities of SOx and NOx when burned. The industry needs to arm itself with clear responses to these and similar misconceptions, and to communicate those responses loudly and clearly, if it is to survive.

Jan 1, 2011

A method, based on the macroscopic population balance equation allowing the dynamic simulation of a multistage adsorption plant given an arbitrary rate expression, is described. The partial differential equations resulting from this method are simplified using the method of characteristics. The simplified equations can then be solved using standard ODE integration techniques. The procedure is illustrated by means of data typical of a CIP application. Requirements for data structures which allow the incorporation of the carbon-in-pulp (CIP) model (and other unit models) into a general metallurgical simulator are described. Based on these considerations, it is concluded that more generality in the description of distributed quantities such as loading and particle size is provided by the use of mass density at fixed class boundaries, rather than discrete masses within fixed classes as has hitherto been used by ore-dressing simulators.

Jan 1, 1987

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By L. A. Jagger

The world?s second largest producer of platinum, Impala Platinum Ltd, approved two new twin shaft projects at the end of September 2004, Nos. 16 and 20 Shafts. Both shaft projects are stand-alone entities and are being sunk from surface. Previously Impala had embarked on a strategy of extending the life of its third generation shafts by means declines. No. 16 Shaft is the first of a new fourth generation shaft complex, while No. 20 Shaft is the last of the third generation type shafts in the so-called shallow to intermediate mining zone. This paper details the basic designs of each project and covers the initial implementation. Although both projects are twin shaft systems, the access methods from the shafts to the reef horizon differ. Initiatives implemented to speed up the projects are also briefly covered.

Jan 1, 2006

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, there by lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3Dmulti-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2006

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By G. Ferrara

The mathematical framework of a well-established model proposed earlier by the authors for the screening process is briefly recalled. Some numerical methods for the application of the model, concerning numerical solution of the equations and parameter estimation, are indicated. Some applications of the model to improve screening operations, sizing of screen, simulation of screening and of integrated plant operations are discussed, and the computer software to be used for these purposes is described in detail.

Jan 1, 1987

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013