Search Documents

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By G. F. Skala

Additional testing of two prototype instruments for the discrete detec­tion of submicrometer particles in metal and nonmetal underground mines is described. The detectors are designed to utilize properties of submicrometer particles to distinguish between those produced by fires from mine ambient particles primarily resulting from diesel engine exhaust. One instrument is based on the ability to pyrolyze fire produced parti­cles, but not diesel exhaust particles. An alarm is produced when the ratio of pyrolyzed to unpyrolyzed particles exceeds a preset value. The other detector utilizes a continuous flow ion chamber preceded by a denuder to remove charged particles. Discrimination against diesel produced submicrometer particles results because the diesel particles are naturally more highly charged than fire produced particles. In-mine testing was conducted over a period of several months. Both in­struments exhibited an ability to discriminate against diesel exhaust. However, problems with the recording equipment, and with the instruments themselves, due to large ambient dust particles, prevented enough data from being obtained to choose between the two methods. Recommendations to correct the problems are made.

Jan 1, 1982

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States west of the Mississippi, and Information Circular 8704 covers States east of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two Information Circulars.

Jan 1, 1976

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By E. K. Stanek

This report contains the results of an investigation into the feasibility of periodically measuring parameters of the insulation for a mine electrical power system in order to detect incipient faults. The variety of insulation parameters evaluated included insulation resistance, dissipation factor, power factor (vs. applied voltage), current harmonics, leakage current, infrared radiation, as well as certain circuit breaker parameters and tests. In order to augment field tests a program of accelerated life testing was also carried out. Apparent inconsistencies in data were identified as the result of environmental effects, primarily temperature and relative humidity. A series of environmental tests were conducted to develop correction factors that allow one to refer measured parameters to standard conditions. A portable data collector was develop-ed to aid in the accurate collection and analysis of laboratory and field data. The primary conclusion is that insulation deterioration can be measured and failure predicted with reasonable confidence. The secondary conclusion is that most of the tests are impractical in the field although useful in the laboratory. Infrared sensing, insulation resistance and dissipation factor are the best insulation field tests when portability is taken into account.

Jan 1, 1979

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990