Search Documents

By George A. Savanick

This paper reviews advances in the art of borehole (slurry) mining made by the Bureau of Mines from 1974 to 1980. The design of a proto-type borehole-mining tool (BMT) developed by the Bureau of Mines is pre-sented along with production data, reclamation data, and an application of the BMT to the mining of coal, uraniferous sandstone, oil sands, and phosphate ore. The BMT was first used near Wilkeson, WA, where steeply pitching metallurgical coal was mined at 8 st/h from a depth of 25 to 75 ft. Next, 940 st of uraniferous sandstone was mined at 8 st/h from a depth of 75 to 100 ft in Natrona County, WY. One thousand short tons of oil sands was mined in Kern County, CA, at the rate of 14 st/h from a depth of 110 to 150 ft in 1979. Most recently, 1,700 st of phosphate ore was produced at 25 st/h from deep (230-to 250-ft) deposits in St. Johns County, FL. Progressive improvements were made in the borehole mining technique. These include the use of the hydrostatic head of a water-filled borehole for roof support, and the development of methods to survey and backfill mined-out cavities.

Jan 1, 1987

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau&apos;s program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior&apos;s Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers&apos; demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By E. L. Litchfield

The electrification of ammonium nitrate-fuel oil (AN-FO) blasting agents by pneumatic loaders is described and discussed. The consequences of the electrification are considered in light of the initiation requirements of electric blasting caps. It is recommended (1) that semiconductive loading tubing be utilized and (2) that the resistivity of the AN-FO be controlled; it is further recommended that the operator (3) test to assure continuity of the electric detonator legwire-bridgewire-legwire circuit prior to insertion of the cap into charge or borehole, (4) keep the legwires shunted but not otherwise connected to ground during loading of the blasting agent into the borehole, (5) assure that the borehole is discharged prior to hooking up the detonator leads, (6) assure that he is himself discharged prior to handling the detonator leads, and (7) assure that the blasting cap leads are never carried to the AN-FO loader. The basis and significance of these recommendations are explained.

Jan 1, 1968

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977