Search Documents

By M. Ganster

Austria’s biggest supplier of oil and gas, transports gas through the West Austria Gasline for domestic consumption. In addition, the OMV also works as gas carrier and ensures the transit into neighbouring countries.

Jan 1, 2010

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur. Two recent render-safe operations conducted in and around urban environments dealt with deteriorated, sensitive dynamite and damaged blasting caps. Utilizing innovative neutralization chemicals and processes to render-safe the deteriorated dynamite, while protecting the general public, proved to be the safest, most environmentally responsible and cost-effective way to approach the problem. In both cases, the explosives, old dynamite and detonators were found in abandoned, unlocked magazines. The dynamite was in a significantly deteriorated state, which was evident due to the nitroglycerine found leaking in,around and under the dynamite cartridges. Iron wire permissible electric blasting caps were also found in a corroded condition with exposed explosives and un-shunted lead wires. With occupied buildings within 180 feet (54.86 meters) of the magazines, any procedure (e.g. transporting, countercharging, burning) that could potentially cause a detonation was not an option. In the event of an unplanned detonation during neutralization operations, several blast mitigation methods were employed to safeguard the site. This operation and a similar one with over 1,000 pounds of crushed and buried leaky dynamite were unique since all the explosives were rendered-safe and neutralized on site. The use of advanced neutralization products and filtering processes allowed for a safer, more environmentally responsible way to resolve the problem. The magazines and all residual solids and fluids were tested and confirmed by independent labs to have no explosives residues. The effluents were treated on site, tested and met safe levels, so they were disposed of at a local municipal wastewater facility.

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Andy Hudson, Stuart Brashear, David Lilly

Because of greatly increased timing accuracy, electronic detonator systems are a well-known and widely accepted major tool to control and reduce ground vibration. At a Southeastern quarry the authors found that the use of electronic detonators improved the reliability of the well known cubed root scaled distance equation for determining air blast. In addition, the authors noticed significant correlations between selected major peak particle velocity frequencies and air blast magnitudes. The major peak particle velocity frequency alone is a close approximation to air blast magnitudes. This relationship is not as significant or not always evident when standard pyrotechnic initiation systems are used.

Jan 1, 2009

By Guy Bridges

Site formation works requiring excavation of rock at the Queen Mary Hospital redevelopment site was restricted due to extremely low ground vibration limits. Non-Explosive excavation method called Electro Power Impactor (EPI), sometimes called Plasma Blasting, was utilised to help ensure the rock excavation rate could meet the required programme.

Feb 1, 2020

By Catherine Johnson, Kelly Williams

Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount

Feb 1, 2020

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Henry P. Jr Van Ormer

During any blast hole operation the first choice to be made is hole size - it seems simple, just calculate all the factors, spacing, burden, depth, rock characteristics, powder factor, etc. and you have it - Hole Size. But we all know that it is not that easy - the "hole size" is part of a system and many other situations can have great impact on the optimum production Blast Hole Size - such as crusher characteristics, hauling capability, mucking capability and - Drilling Capability!

Jan 1, 1983

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Ismael Gottreux Vollet, Carlos A. Muñoz Lira, Alejandro Ferrada Vergara

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the ore body. So far, the use of Pre-Conditioning (PC) with Hydraulic Fracturing (HF) has shown positive results in terms of seismic response and caving ability, while preconditioning combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.

Jan 1, 2016