Search Documents

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Lifeng Li, Jhon Silva-Castro

"Signature Hole Technique is one method to assess the vibration waveform of a production blast.Methematically, it is the convolution between a prior measured waveform of a single blast hole (signature) and a given time delay sequence (comb function). Being an advantage, the inverse operation of convolution, known as deconvolution, can be used to estimate the signature."

Jan 1, 2017

By Courtney Vallejo, Rafiqul Tarefder

This study examines the effects of small scale airblast experiments on cohesive soils and the resulting ground vibrations and crater geometries. Relationships for ground vibration attenuation with soil depth and distance from the blast source were developed. The study is part of a broader research topic of understanding the vulnerability of earthen embankment dams to blast loading. Many earthen embankment dams in the United States were constructed more than fifty years ago and were not designed to withstand high-stress loading such as blast loading. These structures may be susceptible to failure and it is important to describe the response of the earthen dam during a blast event.

Jan 1, 2013

By Carl E. Jones

This presentation discusses the properties of the two-component explosive, KinePak, and how it is used by the utility industry.

Jan 1, 1978

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By John Brennan

Necessity, they say, is the mother of invention. Certainly that sentiment held true during the early stages of explosive engineering. While seaside forts were concerned over static ignition of their black powder caches in the 14th century1, the mining industry in the 1800s were plagued by accidents surrounding the ignition methods for their black powder blasts.

Jan 1, 2011

By David Flores, Benjamin Cebrian

This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

Feb 1, 2020

By John W. Brown

During the summer of 1994 the mining industry experienced numerous accidents involving blasting related incidents. The Tri-State Chapter of Explosives Engineers planned a meeting to discuss three of these accidents.

Jan 1, 1995

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By D P. Proudfoot, S G. Keith, D P. Onagi

A number of aspects of the Canadian concept for nuclear fuel waste disposal are being assessed by Atomic Energy of Canada Limited (AECL) in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, Canada. One of the major objectives of the work being carried out at the URL is to develop and evaluate the methods and technology to ensure safe, permanent disposal of Canada's nuclear fuel waste.

Jan 1, 1996

By Ravi Sahu, Kris Jeremiah

This paper aims to study the benefits of using Post Processed Kinematics(PPK) surveying methodology combined with Drone photogrammetry to achieve highly precise positioning (X, Y, Z) of drill holes based on the drill pattern and to highlight innovative workflow of transmitting the drill plan to smart drills for accurate drilling.

Feb 1, 2020

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By J. Schoonover, A. Moore

In the explosives industry, individuals face a multitude of hazards while working in mines, quarries, and construction sites. Safety becomes an ever-present driver as companies attempt to control costs, promote quality service and products, and grow business all while ensuring employees return home safely every day. One of the most challenging hazards that threatens the goal of absolute safety is flyrock. Ensuring that a blast does not result in rock leaving the blast area, thereby creating a danger for personnel in the vicinity, can be complicated due to the multitude of factors. Shot design, geology, operational procedures/techniques, explosive products, security plans, communication methods, and drilling practices can all adversely affect the safety of individuals helping execute a blast through an increased risk of flyrock. Flyrock can also pose a major threat to the public and other non-blasting personnel in proximity. Like many other industries encountering various challenging hazards, the explosives industry has recently adopted innovative technologies to help mitigate the risk of complex hazards such as flyrock. Specific applications of Unmanned Aerial Vehicles (UAVs), commonly referred to as drones, employed in the explosives industry can help reduce the likelihood and severity of a flyrock incident. This paper explores a case study and theories of how the integration of drone technology within blast security plans, mine planning, blast design, design auditing, and blast area clearance procedures can help to decrease the risk of a flyrock event through the provision of data and information previously unavailable. Multiple opportunities exist during a blasting operation to gather data using drone technology. It is these data-gathering opportunities that can be leveraged to be maximally equipped for the mitigation of flyrock. Better data from drones can be sourced and used in security plans and clearance measures as well as utilized during mine planning and blast design. Increases in the quality and quantity of information during these crucial steps of blasting has proven to be an effective way to increase the peace of mind for explosive end users. This peace of mind, along with design flexibility and adherence to performance, is why the integration and utilization of drone technology is key for effective flyrock risk reduction

Jan 1, 2024

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By Benjamin Cebrian

The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

Feb 1, 2020

By Bonifacio Digay

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia.The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.

Jan 1, 2012

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020