Search Documents

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By Dale Preece, C. Mick Lownds

Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control.

Jan 1, 2008

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints.

Jan 1, 2002

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Bill Williamson, Doug Richmond, Kerri Kuntz, Gus Gilman, Larry Heywood

This was a description by the poet of what occurred over two centuries earlier to Hannibal’s troops as he passed through the Alps. Interestingly, the pass that many feel is the route that Hannibal chose, Col de la Traversette, is the sight of possibly the earliest avalanche mitigation known. Monastery records describe a tunnel built in 1470, near the top of the pass designed to protect pilgrims from the upper slopes. For the next several centuries, avoidance and reinforced structures were the primary tactics to defend from avalanches

Jan 1, 2009

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Ian R. Firth

For the majority of open pit precious metal mines in the western United States, grade control practices have evolved as a direct result of the variable geology of the ore body and the lack of a clear visual or geologic distinction between ore and waste material. These practices often include the extensive use of buffer or choke blasting, in an attempt to minimize lateral movement of the muckpile. The Mackay School of Mines is conducting ongoing research, which aims to develop a practical method of measuring the movement of discrete “targets” placed within the body of the blast. The movement experienced by these targets can then be used to interpolate the movement of the blast as a whole. Typically, the boundaries between different material types are known as digging limits or polygons and are marked using colored flagging on the muckpile. If material movement can be measured using targets placed in the blast, these digging limits can be altered to reflect the blast-induced rock movement, reducing dilution and improving value recovery.

Jan 1, 2002

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015