Search Documents

By Charles A. Schacht

"Relining, lining maintenance, and ladle repair can represent a significant cost in steelmaking. Therefore, the objective of all steelmaking shops is to minimize this cost and to maximize the lining life. However, the thermomechanical behaviour of the ladle lining is highly complicated and sometimes misunderstood. The ladle design also has a significant influence on lining life. Other factors which have a direct influence on lining life are the shop lining installation practices and manner in which the ladle is used. The objective of this paper is to provide an understanding of the impact of these factors as related to improving the integrity of the lining and increasing lining life.Fundamentals of Steelmaking Ladle Lining Expansion ForcesNumerous studies have been conducted by the author on steelmaking ladles with molten metal capacities ranging from 110 ton s to 350 tons. The steelmaking ladle typically has a sidewall plate with a slight taper and for analytical purposes can be classified as a cylindrical vessel.A typical ladle is described in Figure I. The ladle sidewall lining usually consists of a working lining and a safety lining. Although the type of refractory used in the working lining varies based on the type of steel produced and other metallurgical requirements, the refractories typically used are: 70% alumina brick; direct bond mag-chrome brick; resin bond dolomite brick; and direct bond dolomite brick. Fireclay brick, high alumina brick, or a similar strength brick is used as the safety lining.Normally, the ladle lining is exposed to a through-thickness temperature gradient and restrained by the ladle sidewall plate, is described in Figure 2. The hot face side of the refractory lining develops a compressive thermal force and the ladle sidewall plate develops an equilibrating tensile force. The radial joints open on the cold side of the working lining as the lining joints have little or no tensile strength. A radial compressive load (P) develops between the working lining and the vessel shell due to the thermal restraint imposed on the lining by the shell. The radial compressive load is transferred from the working lining through the safety lining onto the ladle sidewall. Therefore, the safety lining must have the strength to accommodate the radial compressive load (P)."

Jan 1, 1991

By Jaime V. Ongpin

"The author will give a capsule history of Benguet Corporation and attempt to identify its operating environment and underlying ""strategy"" until 1974, when the company's management assumed office. The company's operating environment and ""interim strategy"" from 1975 to 1980 will be described. The discussion will cover an environmental forecast and define the company's"" strategy for survival"" for the balance of this century.IntroductionIn December last year, I was asked to deliver a pa per for the management lecture series a t the Asian Institute of Management in Manila. The paper was entitled "" The 1970's: A Decade of Disaster For New Mining Projects"" . In that paper, it was my task to review the results of new mining projects in the Philippines during the previous decade. The task was not a happy one, for the results themselves were not only unhappy, but disastrous on a scale unprecedented in Philippine history. Out of a total of 17 major mining project s involving an aggregate capital investment in excess o f US $2 billion during the 1970s, only three project s have been profitable, and all the rest have either gone "" belly up"" or are teetering on the very edge of financial disaster.It is in the context of this shocking record of widespread financial dislocation in the Philippine mining industry, (which in varying degrees appears to have been paralleled in virtually every other country in the world where mining is an important sector of the economy) that I address myself tonight to the theme of this symposium. My paper is entitled ""Risk Management Strategy in Mining"" and it is sub titled ""Can Benguet Corporation Survive to Celebrate its Centennial in 2003?"". I have inserted the word ""Strategy"" and added the subtitle, because I wish to make it clear first, that my presentation to you tonight will be focused exclusively on the strategic aspect s of risk management, and second that I will limit myself to Benguet's own ""in-house"" experience and perspectives on this subject. I would caution you therefore, to consider my views within this restricted framework, and in light of the particular and sometimes peculiar circumstances within which Benguet Corporation operates."

Jan 1, 1983

By Technische Universität Braunschweig, K. Saksl, J. Furste, P. Eschenbacher, F. Brunke, D. Wolter, M. Kohnke, C. Siemers, J. Kiese, M. Schlemminger

"In general, titanium alloys combine outstanding mechanical properties with corrosion resistance and biocompatibility and are, therefore, used in many challenging applications. Nevertheless, for special products, well-tailored properties are required which might not be achievable by a specific design so that new or modified alloys are needed. In this overview paper, alloy development strategies performed at the Institute for Materials of the Technische Universitat Braunschweig are discussed at different examples, namely, (1) oxidation-resistant, microstructural-stabilized and cold-workable alloys for exhaust applications, (2) aluminum- and vanadium-free, medium-strength and cold-workable alloys for implants and osteosynthesis applications and (3) free-machining alloys by the addition of particles with low melting points for non-safety critical light-weight constructions to replace heavier steels, e.g. in automotive applications. A special focus is set on the alloy development techniques and the analyses carried out to achieve well-balanced properties by the optimization of the alloy compositions. INTRODUCTIONTitanium belongs to the allotropic metals and can therefore exist in two different equilibrium lattice modifications. Pure titanium crystallizes at 1668°C in a body centered cubic (bcc) structure called ?- titanium which at 882°C transforms to a hexagonal close packed structure (hcp), the a-titanium. A martensitic ?-to-a-transformation is possible at large cooling rates. This thermally induced hexagonal martensite is called the a'-phase. The transformation temperature named ?-transus-temperature (T ?) can be influenced by alloying elements (Peters & Leyens, 2002).For titanium alloy production typical alloying elements are aluminum (Al) and oxygen (O), both a-stabilizers shifting the ?-transus temperature to higher temperatures, whereas tin (Sn) and zirconium (Zr) only show a limited influence on the ?-transus temperature. The ?-stabilizing elements are subdivided into two groups: Niobium (Nb), molybdenum (Mo) and vanadium (V) stabilize the ?-phase between the melting point and room temperature and are therefore called isomorphous -stabilizers. Elements like copper (Cu), iron (Fe) or silicon (Si) also stabilize the ?-phase to lower temperatures but undergo a eutectoid reaction during cooling. ?-titanium then dissociates to a-titanium and an intermetallic compound. Consequently, these elements are called eutectoid ?-stabilizers (Boyer, Welsh & Collings, 1994)."

Jan 1, 2016

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan&apos;s first highgrade uranium mining operation, which set the stage for the province&apos;s current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world &apos;s largest uranium companies.Cameco&apos;s $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By A. Singh

"The flotation of fine minerals less than 10 µm in size is an age old challenge spanning both the precious metal and industrial mineral sectors across a range of commodities. This problem has been brought into sharper focus by the emergence of the practice of fine grinding of flotation feed to effect better liberation of the targeted minerals. However, the ability of conventional flotation cells to effectively float the liberated fines remains questionable. In order to overcome this problem, Gold Ore postulates the “Bringing the Mountain to Mohamed” hypothesis which comprises the steps of gas nucleation on particle surfaces, aggregation of particles and levitation of aggregates. Testing of this hypothesis at Mintek, South Africa, showed a ~180% increase in the Kelsall kfast factor coupled with a projected recovery improvement of ~4 % for the Mach Reactor case coupled with a final concentrate grade of ~2 times that of conventional flotation. These fundamentals were then extrapolated to plant scale with Mach Reactors installed on the flotation feed at Platmin’s Tailings Scavenger Plant (TSP) with the objective of scavenging the fine minerals lost to tailings by the main plant. This paper details the theory, pilot plant results as well as key aspects of the full scale plant design supplemented by operational plant observations after commissioning. This game changing application is regarded as being pivotal to future flotation plant design whilst providing the technology leverage required for the survival of mineral operations in an economically unfriendly environment.INTRODUCTION - THE CONUNDRUM OF FINE PARTICLE FLOTATION“If the mountain won't come to Mohamed then Mohamed must go to the mountain” is an age old saying written into the book of proverbs in 1670. Legend has it that Mohamed promised his people that he would summon a mountain to come over to him so that he could offer up his prayers from its summit. After numerous attempts at moving the mountain went in vain, Mohamed, quite unabashed, said “Well if the mountain will not come to Mohamed, then Mohamed will go to the Mountain.” In this analogy, Mohamed is a fine particle <10 µm and the mountain is a bubble within a flotation system. The age old challenge is how to bring these two together to achieve attachment?"

Jan 1, 2016

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By V. Cvetkovic, L. Zou, L. Jing

"Sorption process plays a significant role for solute retardation in rock fractures. In this paper, for the aim to investigate the effect of sorption on solute transport in a single rough fracture, a 2D model of representative single rock fracture was built and its roughness was statistically characterized based on the measured data of rock surface topography by laser scanning. A Finite Volume Method (FVM) code was developed to solve the Navier-Stokes (NS) equations and transport equation for numerical modelling the process of fluid flow and solute transport in the rock fracture model. Two groups of simulations were conducted: with and without the consideration of the sorption process with different average flow velocities. The results show that the surface roughness increased the complexities of flow fields, and the non-linear sorption process plays a significant role in the retardation of solute transport through rock fractures. The sorption process caused an obvious lagging time in both the solute concentration fields (plumes) and corresponding breakthrough curves. This lagging time increases with the distance from the inlet boundary, and relatively decreases with the increase of mean velocities. INTRODUCTIONFluid flow and solute transport in fractured rocks is an important research topic for performance and risk assessments for rock engineering projects concerning geo-environment safety, such as radioactive waste disposal, mining, geothermal extraction, reservoir engineering and other contaminant transport processes in geosphere (Berkowitz 2002).The solute transport in the rock fractures mainly involve the advection, surface sorption, matrix diffusion, dispersion, radioactive decay and chemical reactions, governed by general transport equations (e.g. Bodin et al., 2003). Among these transport phenomena, the sorption on the fracture walls can alter solute migration between the fractures, and play an important role in natural retention of solute transport (Weber et al., 1991; Wels et al., 1998; Kumar 2007; Dai et al., 2012). The aim of this study is to investigate the effect of sorption on the solute transport in a single rock fracture with rough surfaces. More complex transport processes, such as matrix diffusion, dispersions, radioactive decay and chemical reactions, are not included in this study."

Jan 1, 2015

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By J. Koponen, K. S. Stadler, A. Fuerst, S. Gaulocher, Th. von Hoff, R. Veldsman

"Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO).A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components:1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user.2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer.3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD.In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples."

Jan 1, 2012

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015