Search Documents

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By George S. Martin, Michael D. Winship

"Placer Dome Inc. is the operator of the Musselwhite project located 100km north of Pickle Lake, Ontario. J.S. Redpath Limited was contracted to conduct an underground exploration program using shaft access.During the winter of1988, the shaft collar was established in 16 metres of water bearing sand and till overburden. This paper will illustrates the engineering techniques used to overcome the obstacles to installing a shaft collar in deep overburden. Specialized dewatering and piling procedures were employed.INTRODUCTIONHarold and Allan Musselwhite discovered gold in the Opapimiskan Lake area, north of Pickle Lake, in 1962. The prospectors were grubstaked by ten companies in 1973.A diamond drill program was initiated shortly thereafter.In 1983an underground ramp exploration program was carried out on the West Anticline portion of the property. The program was unsuccessful in establishing an ore reserve so surface exploration continued. In 1986the ""T"" zone was discovered. Further surface drilling was done and an over-all drill-indicated reserve of 6 million tonnes at 7 grams per tonne was outlined. The gold mineralization occurs in several vertical tabular deposits within the iron formation. In late 1987the joint venture partnership, now consisting of Placer Dome Inc., Inco Gold Co., Corona Corporation and Esso Minerals Canada, contracted J.S. Redpath Limited to conduct an underground exploration program on the ""T"" Zone.The scope of work for the project was to: 1. establish a 45 km winter road in 1988 and 1989;"

Jan 1, 1989

By James Logan

BC Alkaline CuBC Cu--Au PorphyriesAu Porphyries ?Formed over narrow time interval ~205 Ma ?from silica deficientvsalkali-enriched magmas ?At shallowdepths ?Structuralcontrol ?Cu-Au-Ag, trace Mo ?Oxidized system anhydrite, magnetite ?Multipleintrusions & multiplemineralized centres

May 1, 2006

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By Jacques Ouellet

Outline What is Microwave energy Investigation of transparency of 40 minerals Melting of Andesite in a MW oven Numerical modeling /Computer Simulations o FEM analysis ?? Some laboratory experiments o Particle Modelling Mw Application to Rock Breakage o A MW Rock Drill Prototype Conclusions What is Microwave energy Microwave energy is an electromagnetic wave consisting two electronic & magnetic wave traveling perpendicular to each other and transporting energy with the speed of light.

May 1, 2008

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By P. R. A. Andrews, R. K. Collings

"There are more than thirty-five deposits or occurrences of celestite in Canada, chiefly in Newfoundland, Nova Scotia, New Brunswick, Ontario and British Columbia. Deposits of economic interest are the Lake Enon and MacRae deposits in the Loch Lomond district of Cape Breton Island, Nova Scotia. Two Cape Breton deposits were operated from 1969 to 1976 by Kaiser Celestite Mining Limited, which supplied an upgraded celestite concentrate to an associated strontium carbonate plant at Point Edward, near Sydney.The MacRae deposit is of current interest because of its possible development for strontium carbonate production using the ""black ash"" process. This process involves chemical leaching, rotary kiln calcining with petroleum coke, washing and treatment with carbon dioxide.Celestite is the basic material used in the manufacture of strontium chemicals, principally strontium oxide, carbonate, nitrate, chromate, chlorate, chloride, sulphide and phosphate. Strontium chemicals, in turn, are used in the manufacture of glass and ceramics, in pyrotechnic devices, in the production of strontium metal and in other metallurgical applications. Recently, strontium ferrites have been introduced into permanent ceramic magnets."

Jan 1, 1991

Evolution of Maintenance Practices. Mechanization processes in underground mining operation became stronger in the 70?s - 80?s. Did maintenance practices changed over the years ? What are the the major differences of today?s practices? Speaker, Robert Hamilton Working at different positions into maintenance organization since over 25 years, Robert has accumulated a various and rich experience of ways to maintain equipment. He started as mechanic on construction projects and open pit mines. Early in his career Robert had supervision's responsabilities. He started in open pit operation (QCM) and after in underground operation with Lac Minerals, working at Bousquet, Doyon and Louvicourt mines, as U/G mechanical foreman and mechanical general foreman, and Maintenance superintendant with Cambior . He also experienced the underground mines equipments supplier's side working with Sandvik Canada.

Feb 1, 2008

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By D. Assmus, S. Daly

"Poor fragmentation, high toe areas, excessive shovel wear and tear and frequent re-drilling and blasting of certain tough waste rock zones in the Lomex pit in the early 1980snecessitateda better understanding of these zones.A combination of geotechnical mapping, penetration rate data, toe elevation contouring and observations on shovel and drill performance were used to determine the character and extent of these zones. This complementary information was brought together by the geotechnical mapper and the explosives supervisor.Distinct zones with particular geological characteristics were determined. A classification system with three types of blast and dig-ability was developed for the Lomex pit and later applied to the Valley pit, with considerable success. The three blast zone types are called ""poor"", ""f air"", and ""good"". This system will be described in detail.The explosives supervisor adjusted the blasting parameters to each zone, in particular, pattern spacing and burden. The resulting powder factors showed considerable variation between the poor, fair and good zones within each pit as well as between the two pits. Pattern geometry and length of collar were also adjusted to improve fragmentation. Cost savings resulted from less re-drilling and less wear and tear on drills and shovels in the poor zones and more efficient use of explosives in all the zones. An annual estimated cost savings of well in excess of $1,000,000 is realized at Highland Valley Copper. A by-product of the mapping was the determination of unstable structures and water flowing zones. Blasting was then adapted to this information for enhanced slope stability."

Jan 1, 1992

By H. Soto, P. Lacombe, R. del Villar

"During the summer of1989, Les Mines Selbaie, with the cooperation of Université Laval initiated a research project to evaluate the column flotation technology for its concentrator near Joutel, Quebec. The experimental work involved both a 5 cm by 11 m laboratory column and a 45 cm by 10 m home-made pilot unit Amenability tests were conducted using both units on various streams of the plant. Results showed that columns are not suitable for the copper cleaning circuit because the loss of precious metals, associated with the rejected pyrite, overcome the improved copper metallurgy. On the other hand, column testing at the zinc circuit showed improved zinc selectivity.Scale-up testing was', therefore, conducted on the first zinc cleaner concentrate using the laboratory-size column. The influence of variables such as porous parger grain size, wash water flow rate, airflow rate and froth depth values on column performance was' first assessed. Scale-up parameters were then determined using the optimal operating conditions from the previous tests. Simulation facilitated the determination of the most convenient plant-scale column arrangement.A number of conclusions concerning the experimental determination of scale-up parameters are also presented."

Jan 1, 1993

By M. L. Jeremic, G. J. P Delaire

"The mechanical aspects of cable bolt failure are considered from the point of view of properties of grout and cable, as well as of the rock in which it is anchored. The results from recent investigations made in-situ as well as in the lab are combined and presented with reference to other work done in the area. An attempt is made to stimulate the thinking along these lines so as to initiate further research which may enhance the design of cable bolting as it applied to mining operations.IntroductionIn the past twelve year s systematic cable bolting has found application in many areas. In civil engineering rock anchors have been used to provide tension at the heel of a dam permitting the reduction of its cross section. They have been used in retaining walls to reduce construction time and costs by eliminating the need for struts and braces which complicate pouring the foundation walls. It is also possible to use rock anchors in providing reactions where tall buildings are subjected to uplift on one side due to wind forces. Cantilever bridges may be constructed by implementing rock anchors to provide anchorage requirements. Anchorage piles or dolphins or mooring ships have also been built using these. In the mining area rock anchors, commonly known as cable bolts because they are made of hoist cable may be implemented in the reinforcement of hanging walls or to retain rock slopes.In order to sustain de-pressurized ground where rock separation developed along the pressure arches, cable bolts were utilized at the Tsumeb Mine in South-West Africa and also at the Strathcona Mine in Sudbury, Ontario, In both places old degreased hoist ropes were installed in downholes from crosscuts above a given stope and then grouted without tensioning. Jeremic and Cassidy described the use of cable bolts to increase hanging wall stability and postpone fracturing, in addition to producing pre-support for improvement of stope back stability."

Jan 1, 1983

By Noko S. Phala

The energetics of CO and CO2 hydrogenation to methanol were studied on a gold surface via periodic and cluster DFT calculations. CO hydrogenation appears to be much easier than CO2 hydrogenation on an Au(111) surface. The use of a cluster model does not seem to improve the energetics of CO2 hydrogenation. It is concluded that an active support (e.g. ZnO) will be required to increase the productivity of a gold surface towards synthesis gas conversion. The energetics of CO and H2 adsorption are improved on the cluster model compared to a slab model of an Au(111) surface, suggesting that nanosized gold particles may be beneficial in CO hydrogenation.

Oct 1, 2003

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By James K. Gowans

"Cominco Ltd's Polaris Mine, located on Little Cornwallis Island, Northwest Territories (latitude 75degrees 30') went into production in late 1981, becoming the world's most northerly base metal mine. The concentrator, powerhouse, shops, offices, dry and warehouse, were uniquely designed and constructed on a 100f t wide by 400 ft long by 65 ft high barge. This process barge was constructed in southern Canada at Trois Rivières, then towed 3,500 miles into the High Arctic Islands and beached on Little Cornwallis Island.The paper deals with the original design philosophy, flowsheet and the initial year's operation of the Polaris process barge.IntroductionTo bring a mining property into production in the Canadian High Arctic, a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these fact or s, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gamed at the Black Angel Min e on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during the ""shipping window"". The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months' production was gained by opting for the ""barge"" approach."

Jan 1, 1983

By J. A. C. Fortescue

"Reconnaissance geochemical mapping, based on the chemical analysis of waters, stream, and / or lake sediments had its origin in geochemical prospecting surveys carried out in New Brunswick during the 1950s. More recently, reconnaissance geochemical surveys carried out by government agencies for mineral resource appraisal purposes have been seen as a special case of regional geochemical mapping which is carried out with the aim of describing geochemical patterns f or elements which may he interpreted for mineral resource appraisal, environmental or geological purposes. The interpretation of pal/ ems on regional geochemical maps is based on the concepts of landscape geochemistry, in this paper, the regional approach 10 geochemical mapping is described with reference to an experimental regional geochemical survey which was completed in southwest Ontario during 1981-82. II is concluded, on the basis of data pal/ems for one element only (i.e. arsenic), that the new approach has much potential for solving modern problems in geoscience.""If things don 'I alter they will stay as they are... An old adage.IntroductionDuring the past hundred years topographic, geological, and geophysical maps have been made for all, or nearly all, of Ontario. During the past thirty years these maps have become related as components of what is now called geoscience. Geoscience maps at the regional (i .e. 1 :250,000) scale are often used together to solve general problems in earth science especially in relation to prospecting, or mineral re source appraisal."

Jan 1, 1986

By R. W. Lawrence, A. Bruynesteyn

"Pre-oxidation of refractory pyritic concentrates by biological leaching to enhance the recovery of gold and silver in cyan ideation has been investigated. The results of laboratory tests on three concentrates are presented. In all cases substantial increases in precious metal recoveries were obtained following the pre-treatment. For one concentrate, gold recovery of 81% was achieved following an 87% oxidation of pyrite, compared with 24% recovery by direct cyanidation of non-oxidized concentrate. Gold and silver recoveries from the other concentrates were increased from the range 60-78% to over 90% and from 80-86% to over 98% respectively. Operating parameters are discussed and methods of maintaining high oxidation rates are evaluated. Methods of employing this pre-oxidation technique in commercial practice are described.IntroductionMany of the gold and silver deposits now being developed contain precious metals finely disseminated in sulphide minerals such as pyrite. These ore s often present considerable resistance to metal recovery. The ease with which gold may be extracted is usually related to grain size and its manner of distribution within the host mineral. In many cases, a significant percentage of the gold may occur in submicroscopic form, or in solid solution with pyrite, so that even very fine grinding fail s to liberate the metal for recovery by cyanide leaching. Such ores are often termed refractory. Even in cases where liberation by fine grinding is practicable, high cyanide and lime consumption may be experienced due to the presence of specific sulphide minerals, and poor metal recovery may result.Pre-oxidation methods for refractory ore s and concentrates are commonly used to improve precious metal recoveries. Roasting, for example, as a pre-treatment to cyanidation, removes harmful constituents by oxidation or volatilization, and liberates gold from pyrite. In some cases, however, this method of pre-oxidation can result in poorer metal recovery, particularly of silver, due to fusion and the formation of clinker, and the formation of compounds which consume cyanide in the subsequent metal recovery stage. Difficulties in compliance with environmental pollution regulations may also be encountered."

Jan 1, 1983

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984