Search Documents

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

By G Solly, S Parsons, P Leevers, S Ni

Hematite ore has been mined in the Southern Middleback Ranges as blast furnace feed for the steelworks at Whyalla, by what was then BHP, since 1991. With the floating of BHP Integrated Steel as OneSteel in 2001 and the subsequent loss of key mining personnel, breakdowns in grade control methods and procedures occurred. These were compounded by changes in orebody characteristics and grade distribution leading to poor reserve recovery and poor grade control, both which resulted in loss of control of ore specification and severe deviation from the mining schedule. As a result, a total review of grade control, mining method and scheduling procedures was undertaken as well as a review of contractor quality assurance. It was found that sampling methods were poor and unrepresentative, grade control blocking processes were outdated and did not reflect the geology of the deposit, the ore mining method was outdated and did not respect the geometry of the orebody, reconciliation methods were being completed globally and were not reflective of individual areas of the deposit, and that deviations from the mine plan were occurring due to access to high-grade areas outside the schedule in order to bring stockpiles back on grade. Based on these findings, updated sample splitter systems were fitted to drill hole rigs, double bench sampling was implemented (2 + 4 m samples as opposed to 1 + 8 m sample) and a three-dimensional cellular grade control system introduced to better reflect the geology and orientation of the deposit. At the same time ore mining was changed from front end loaders mining on 8 m benches to excavator mining on three lifts on 8 m benches; this aided selectivity and respected the geometry of the orebodies aiding cleaner recovery. Reconciliation is now completed on a blast-by-blast basis, which allows for quick and easy identification of poorly performing areas of the resource model that can then be incorporated back into resource model updates. Regular daily and weekly meetings are also held with emphasis on the mining schedule to ensure no deviation from the schedule in the long term. These improvements have resulted in a lift in reserve recovery both globally and locally associated at the same time with improvement in grade.

Jan 1, 2005

By Allnutt S. L, Carswell J. T, Mutton A. J

The Dugald River Zn-Pb-Ag deposit occurs within the complexly deformed and metamorphosed sediments of the Middle Proterozoic Cloncurry Terrane, Eastern Succession, Mount Isa Inlier. The sedimentary sequence comprises a thick package of variably carbonatic argillitic and siliciclastic sediments of the Corella Formation, Lady Clayre Dolomite and Knapdale Quartzite. A slate and calc-argillite unit locally referred to as the Dugald River Slates is the host to the economically significant deposit. The deformational history of the Dugald River area involved three phases of ductile deformation. The present geometry of the Dugald River Main Lode is recognised as a strike extensive steep westerly dipping tabular sheet, within which a steep north westerly plunging zone of pronounced thickening is evident. This zone is interpreted to have formed during folding via remobilisation of the sulphides into a shoot-like body, the geometry of which was controlled by stretching associated with the folding. Further modification of the shoot and sulphide re-distribution has resulted from late phase transgressive shears. The sulphide mineralisation is characterised by three distinctive sulphide types, laminated, banded and breccia, the distribution of which define two broad zones. The northern zone is a narrow I - 5 m thick stratabound unit comprising finely laminated and banded sulphide mineralisation within a well bedded fine grained argillite sequence. This is part of the Lady Clayre Dolomite sequence and is a predeformational precursor form of mineralisation. The southern zone comprises the thickest development of mineralisation (up to 30 m) characterised by slate-sulphide breccias and veins derived from complex polyphase remobilisation of the sulphide mineralisation. It is this zone which forms a stratabound locally transgressive body within the high strain Dugald River Slates and which contains the main body of economic mineralisation. Sulphide mineralogy comprises sphalerite, pyrite, pyrrhotite, galena and traces of chalcopyrite, pyrargyrite, tetrahedrite, marcasite and arsenopyrite. The present resource for the Dugald River deposit stands at 38 Mt grading 13.0 per cent Zn, 2.1 per cent Pb and 42 g/t AS. The Dugald River Zn-Pb-Ag deposit is regarded as an example of a syndiagenetic stratabound sulphide accumulation which, as the result of polyphase deformation and upper greenschist to middle amphibolite facies metamorphism, has undergone extensive remobilisation and Rccrystallisation.

Jan 1, 1993

By S Meffre, S Golding, K Zaw, J McPhie, R James, S Suphananthi

The Chatree deposit is located in the central portion of Loei Fold Belt, which extends from Lao PDR in the north through centralThailand to Cambodia in the south. Epithermal gold-silver mineralisation at Chatree occurs as veins/veinlets and stockworks with minor breccia in volcaniclastic and volcano-sedimentary rocks of andesitic to basaltic andesite composition and Permo-Triassic age. This preliminary oxygen isotope study mainly focuses on vein quartz of Au-Ag bearing mineralization (Stage 2) and a few samples of late Stage 4 quartz ¦ calcite veins. Quartz from Au-Ag bearing mineralisation has oxygen isotope values ranging from 8.1 to 12.3ë with the lowest values generally occurring at the deeper level (140 m below the surface). The late barren quartz ¦ calcite veins (Stage 4) tend to have higher oxygen isotope values ranging from 11.9 to 12.0ë. The oxygen isotope composition of the Chatree ore fluids were calculated at 250¦C, 300¦C and 350¦C based on homogenisation temperatures of fluid inclusions. The calculated oxygen isotopic composition of the Chatree ore fluid ranges between -1 and 6ë that overlaps with both meteoric and magmatic compositions. This shift in oxygen isotope compositions may relate to processes such as water rock-interaction and/or mixing of meteoric and magmatic fluids. It is interesting to note that the lowest quartz oxygen isotope values are spatially more or less confined to the prominent structures in the centre of the major ore zones. These structures may have been acted as conduits for higher temperature magmatic fluids. The quartz oxygen isotope values increase outwards from the centre of the main ore zones to the margin of the pits possibly due to mixing of magmatic fluids with lower temperature meteoric water. Whole rock oxygen and hydrogen isotope studies are in progress to investigate isotopic trends in the wall rock away from the ore zone. The systematic variation of oxygen isotopes in quartz from the mineralised veins and adjacent wall rocks could potentially be used as a vector to ore. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Smith CB, Boxer GL

The Argyle diamond deposits in the East Kimberley were found as a result of a long term exploration programme, begun in 1972 by the Kalumburu Joint Venture (KJV), to search for diamonds on the Kimberley craton. When CRA Exploration Pty. Limited joined the KJV in 1976, it was re-named the Ashton Joint Venture (AJV). The Kimberley craton was considered prospective by analogy with structural settings of diamondiferous kimberlites in Africa. Diamonds were found during regional drainage sampling in Smoke Creek in late 1979, which led directly to the discovery of the rich Argyle lamproite diatreme (AK1) and associated alluvial deposits of Smoke and Limestone Creeks. The diatreme intruded into quartzites, sandstones and shales of Adelaidean age, and consists predominantly of lapilli ash tuff, with minor coarse and fine ash tuffs, 'non-sandy tuff' and olivine lamproite dykes. Erosion of the diatreme has produced the alluvial deposits of Smoke Creek and Limestone Creek to the north and east. Argyle diamonds are of predominately industrial quality, and the typical diamond is a brown, irregularly shaped, frosted, heavily resorbed form with abundant graphite inclusions, well developed etch channels and prominent hexagonal surface depressions. The pre-feasibility evaluation of AK1 comprised diamond drilling, surface and underground sampling, metallurgical sampling, marketing studies and ore reserve estimation. The proven AK1 ore reserve is 61Mtonne at 6.8ct/tonne. Evaluation of the alluvial deposits gave results of Upper Smoke Creek, 580 000 tonne at 4.6ct/tonne and Limestone Creek, 1.7Mtonne at 3.5ct/tonne. Commercial production from the two alluvial deposits began in 1983 with production for the year reaching 6.2 Mct. Mining of the alluvial deposits at three to five Mct/year is proposed to continue until the start of mining of the AK1 deposit in late 1985 or early 1986 at which time a new processing plant and associated infra- structure will have been constructed adjacent to the AKl deposit in the Limestone Creek area. Production is planned at three Mtonne/year, producing 25Mct/year, which will make Western Australia the largest producer of natural diamond (by weight) in the world.

Jan 1, 1984

By M Araos, I Onederra

A novel explosive formulation that substitutes the use of ammonium nitrate (AN) with hydrogen peroxide (HP) as the main oxidising agent has been developed and tested as part of an Australian Coal Industry Research Program (ACARP) project. The main objective was to provide a step-change solution that has the potential to completely eliminate NOx fumes in blasting. The development of this HP/fuel-based explosive started with a comprehensive detonation characterisation program, consisting of unconfined velocity of detonation (VOD) measurements of samples at different diameters, densities and void sensitisation techniques. VOD results showed that the HP/fuel-based explosive mixtures behaved similarly to non-ideal commercial explosives; in that way mixtures could be tailored to achieve specific detonation performance targets. The next stage of testing in this development involved preliminary confined tests to evaluate the rock breakage potential of the HP/fuel-based explosive mixtures. Fully instrumented single-hole tests were conducted in a limestone quarry. Results from these preliminary trials confirmed the rock breakage performance of HP/fuel-based explosive mixtures. The confined VOD measured in one of the tests was 5100 m/s in a 102 mm diameter blasthole at a density of 0.96 g/ml. The corresponding borehole pressure measurement of this HP charge was 2.61 GPa with a detonation temperature of 2921°C. Based on near-field accelerations, both HP and ANFO charges displayed similar attenuation characteristics in the test conditions. Post-blast observations indicated that the breakage performance of the HP mixtures clearly reflected the in-hole detonation performance measurements obtained, confirming the ability of these explosive mixtures to both fragment and effectively displace the rock mass under evaluation. Further research work continues with the future commissioning of a prototype mixing and delivery unit, the successful completion and analysis of data from multiple-hole trials, and further characterisation work associated with product stability, reliability and performance under different geotechnical conditions.CITATION:Onederra, I and Araos, M, 2015. Detonation and breakage performance of a hydrogen peroxide-based explosive formulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 565–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

By B Lyne

In 1990, the Queensland mining industry had come to the conclusion that new safety and health legislation based on risk identification and control was required if the mining industry was to be effectively and efficiently regulated. In particular stakeholders in the coal mining industry had arrived at this opinion after the industry had suffered a number of major underground explosions over the 14-year period between 1972 and 1986. Also by 1990, a general consensus had emerged across both the coal and metalliferous mining sectors that mining industry was over regulated and, more to the point this over regulation did not encourage industry to identify and address the underlying causes that had led to a cycle of major mining accidents in the state. The prevailing opinion was that the prescriptive legislation left the ownership of risk management with the regulator and not with the mine operator. This paper discusses the background to the development of the Queensland Coal Mining Safety and Health Act 1999 and the Mining and Quarrying Safety and Health Act 1999 and the progress made in improving safety and health since the statutes came into force on the 16 March 2001. The paper discusses the issues that had to be addressed during the development of the legislation including the interaction with other legislation based on based on risk management principles that either overly or interface with the mining legislation. The effect the underground explosion at Moura No 2 in 1994 had on the final content of the new legislation is also considered. Health is often the neglected twin of safety and health legislation and the paper previews the health surveillance system being proposed in Queensland to ensure that health of mine and quarry workers is afforded the same priority as their safety. By increasing the structured management of occupational health problems in our mines there is an opportunity to make significant improvements in mine safety In conclusion the paper reviews the results to date since the introduction of the new mining safety and health legislation in Queensland on the 16 March 2001. Progress has been made and more is yet to be achieved

Jan 1, 2003

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By A Kuras

Segmental tunnel linings are becoming more common in Australia. One current project employing a segmental lining is the City West Cable Tunnel (CWCT) in Sydney. The project has been commissioned by Energy Australia and is currently being constructed by Thiess Pty Ltd. The project includes 1.6 km of tunnel boring machine (TBM) driven, segmentally lined tunnel. The majority of the CWCT will be excavated through Hawkesbury Sandstone. The tunnel is required to carry a 132 kV electrical circuit under SydneyÆs central business district (CBD), between Haymarket and Energy AustraliaÆs City North Substation on Sussex Street. The segmental lining has been designed as a 3.2 m internal diameter, 200 mm thick universal ring with six trapezoidal segments. The design and detailing of this segmental lining presents some noteworthy challenges, including exposure to saline groundwater, and the exclusive use of steel fibres for flexural and tensile concrete reinforcement. This paper describes some of the key elements of the segmental lining design. These include:the case for choosing segmental linings over other forms of tunnel construction;the major design checks required of a segmental lining including ground loading, hydrostatic loading, joint bearing, joint rotation, ram loading and the early strength lifting case;the benefits of using steel fibres over conventional steel reinforcement;the design approach used for steel fibre reinforced concrete;the application of 3D computer modelling in the design;the provision for components including connector dowels and gaskets;the design for passive fire resistance; andthe design for durability of steel fibre reinforced concrete in a saline environment. Segmental lining design requires the application of specialist design approaches. Input is required by the construction team, as the methods of demoulding, handling, transportation and installation impact on the lining design. As the segmental lining is functioning as immediate ground support and also a permanent lining, high standards of manufacture and construction quality control are required to ensure that the 100-year design life is met. The requirement for a watertight tunnel means that detailing and installation of the EPDM gaskets is of importance.

Jan 1, 2008

By Amer S, Novais A. Q, Limpo Gil J

A proprietary hydrometallurgical ammonium chloride process for the recovery of not only zinc, but also copper, lead and silver from sulphidic zinc-rich concentrates has been developed at bench scale by CENIM and INETI (ex-LNET) as part of a research project supported by the Commission of the European Community (DGXII). This paper deals with the innovative chemical aspects applied to this chloride process and also with the more relevant data relating to mass balance, heat balance and process economics. Under mild temperature and oxygen pressure leaching conditions it is possible to extract practically all the zinc together with the other metals of interest and to precipitate simultaneously the solubilised iron fraction as goethite. The pH is kept close to neutrality in spite of the ammonia released in the leaching of the non-ferrous sulphides. A buffer effect is observed mostly due to the formation of zinc ammines which are very soluble in this medium. The zinc is further extracted by D2EHPA, the acidity being neutralised by the ammonia. Most of the ammonium chloride is naturally regenerated in this step. The zinc is recovered as zinc cathodes in a conventional sulphate electrowinning circuit. All the main raw material consumptions excluding the concentrate, such as oxygen, lime and ammonium chloride are linked to the sulphate formation in the leaching step which must be kept as low as possible by decreasing the reaction time under neutral conditions. The process analysis is complemented by the economic evaluation of a reference case. Difficulties encountered in finding a more convenient method of assessing the economics of the process in the absence of a reference price for a complex sulphide concentrate are examined and discussed. The reason why this analysis was performed with a much more optimistic metal prices scenario is also highlighted. The process economics are primarily dependent on the zinc market quotations and of course on the concentrate cost. Around 70 per cent of the total revenue is due to zinc sales. Assuming an internal rate of return of 17 per cent, the price of the concentrate can be as high as 255 $US/t for a plant capacity of 320 000 t/y (90 000 t/y of zinc).

Jan 1, 1993

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By Groves D. I

The Norseman-Wiluna Belt (Fig.1) is a richly mineralized (production 1900 tonnes Au), Archaean greenstone belt, up to 800km long and 200km wide, which forms the major part of the Eastern Goldfields Province within the Yilgam Block. The Belt evolved ca. 2700 Ma ago as an oblique-slip mobile belt between flanking portions of an older greenstone terrane. Volcano-sedimentary successions in the Belt represent two distinct tectono-stratigraphic associations. Sequences of metamorphosed caic-alkaline intermediate to silicic volcanic rocks interlayered with tholeiitic basalts probably represent the remains of a dissected Archaean volcanic arc (or arcs), and sequences composed dominantly of ultramafic to mafic lavas and intrusions, with minor interflow tuffaceous, sulphidic or cherty sediments are interpreted as remnants of the floor of an ensialic marginal basin (Barley and Groves, 1988). Ultramafic volcanism at Kambalda has been dated at 2692 ¦ 2 Ma (Claoue-Long et al., 1986). The dominantly volcanic associations are locally overlain by coarse clastic sedimentary succes- sions. The Belt is also typified by major north- to north-northwest-striking fault systems, shear zones, and tectonic lineaments, many of which are traceable for more than 300km. As well as defining the boundaries of the belt, these structures have accomodated much of the regional strain and acted as conduits for hydrothermal fluids during deformation, metamorphism and mineralization. As a result, most of the epigenetic gold deposits in the Belt occur in subsidiary structures related to these fault systems (Eisenlohr et al., 1988). Deformation involved oblique compression resulting in a closely spaced network of low-angle faults (thrusts) as well as upright folds and oblique- to strike-slip faults (Archibald, 1987; Veamcombe et al., 1988). This was accompanied by regional metamorphism and granitoid emplacement. At Kambalda, regional deformation and metamorphism were synchronous with the emplacement of the Kambalda Granodiorite which has been dated at 2662 ¦ 4 Ma (Hill and Compston, 1986), approximately 30 Ma after volcanism.The tectonic history and style of deformation of the Norseman-Wiluna Belt are similar to those of Phanerozoic oblique- slip mobile belts at continental margins, which are also a major source of hydrothermal gold mineralization.

Jan 1, 1988

By O Otgonbayar, B Bayarmaa, D Batbyamba, S Amar-Amgalan, K H. Natsagdorj, J Nomin-Erdene, B Boldkhuu, T S. Sainzaya

The Argyle deposit in the Kimberley region of Western Australia was the world’s largest accumulation of natural diamonds. Following its discovery in 1979, the mining of associated alluvial diamonds commenced in 1983, followed by the pipe in late 1985. Over the life of the mine to its closure in November 2020, Argyle produced approximately 900 million carats of diamonds. Argyle diamonds are distinctive in having a predominance of brown colours and rare highly-prized pink diamonds, which are a signature of the deposit. The 3D geological model developed from mining and deep drilling shows that Argyle is a composite pipe formed by the coalescence of several steep-sided diatremes, each with their own feeder zones at depth, that were erupted along a NNE-trending fault. The ~1.2 Ga Argyle pipe is comprised of diamondiferous olivine lamproite volcaniclastic rocks and intruded by sparse olivine lamproite dykes. The volcaniclastic rocks are predominantly comprised of unconsolidated quartz-rich lapilli and coarse ash deposits formed by numerous phreatomagmatic eruptions of olivine lamproite magma through Mesoproterozoic water-rich sands and silts. Post-emplacement deformation has tilted the orebody 30° to the north and regional strike-slip faulting has offset, segmented, and elongated the orebody. Recent significant modifications of the geological model resulted from underground block cave operations, producing several critical lessons learnt. Diamond grade and quality reconciliation issues warranted a geological investigation which resulted in the recognition of new volcaniclastic olivine lamproite domains with a broad range of diamond grades, including some very high-grade units. The new lamproite domains had a significant effect on the block cave mining and resultant recovery of diamonds. The new findings enable a more coherent and detailed geological understanding of the volcanic emplacement and paragenetic sequence of the Argyle AK1 pipe. Structural modelling of the deposit also played a major role in the block cave mining tonnage recoveries and daily operations. The re-examination of the geology of the Argyle pipe and the results of this new information reinforces the need for ongoing robust geological work both in the early stages of mining a deposit and continued during the life of the mine.

Mar 22, 2022

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002

It is indeed an honour to address the perth branch of the australian institute of mining and metallurgy and to have the opportunity to talk to you about the future role of upgraded ilmenite on t102 feedstock supply and demand. There have been many papers written on upgraded ilmenite supply and demand and now I would like to share with you QIT's view of the situation first, a word about demand, although I will be talking principally on the supply issue. The principal use of t102 is in the manufacture of pigments which, in turn, are used in paints, plastics, and the paper industry together with a few miscellaneous uses, while a further b% or so of t102 minerals are consumed for the manufacture of titanium metal and for the manufacture of welding electrodes. the total demand for contained t102 is of the order-of 3 million tons per annum, and the general consensus in the industry is that growth rates should be of the order of 2% annually- it is against this backdrop that suppliers must compete with one another and produce least cost materials for the pigment industry. At the moment, supplies are relatively tight, but the generally slow growth in demand coupled with the abundance of titanium bearing minerals should ensure that long term the reverse is generally true. Now, let us examine the supply situation. Titanium is the 9th most abundant element in the earth's crust, so the problem from the producers` point of view is not one of scarcity of titanium minerals, but of how to extract most economically t102 feedstocks from a wide variety of choices- up to the present, all titanium feedstocks are being derived from either rutile or ilmenite rutile, at about 95% t102 content, is indeed a premier raw material which does suffer from potential scarcity and rutile supplies will likely be a diminishing factor in future decades- whereas ilmenite, a combination of iron and titanium oxides found in varying ratios, may be found in huge quantities all over the world.

Jan 1, 1986

The difficulty in screening of ores when the moisture contents reach certain critical levels has resulted in mining circuits using wet processes for screening. While this has been acceptable in past years it is no longer acceptable in certain countries and where the mining company is looking to reduce its impact on the surrounding environment.   Various mining companies have been looking at ways to remove the need of using water, with all its inherent drawbacks and to be able to produce its desired products in a dry process.   This would have the benefits of less environmental impact and cost, (due to not requiring wet processing equipment), less power consumption (reduced equipment needed), no corrosion issues, no contaminated waste waters and reduced maintenance activities.   Until recently this has proven elusive or with technical restrictions with current available acceptable technologies for high capacity plants.   One major mining company began seriously exploring ways to overcome this dilemma so that they did not replicate their current ways of operating for their new expansion plans.   They partnered with Metso Minerals to undertake extensive groundbreaking laboratory test work and provide potential solutions as to how to solve this. The laboratory test work proved interesting enough to design, manufacture and test on the actual mining site a prototype screening machine in the circuit.   This break through in screening technology reduces the environmental impact on the area in which the mine is located by: eliminating the storage and use of water, reduction in energy consumption due to having no pumps in the plant, reduction in plant costs and the upstream affects on the environment process used to manufacture and ship the materials the plant structure is built from, and no large tailings dams to take up land space and affect the environment through groundwater/ water table contamination and the negative effects on animals and ecosystems Laboratory test were conducted and a full size machine was installed at the plant site along side conventional machines. The screen size (2.4 m wide x 6.1 long double deck) was determined by the size of screens currently in operation at the mine. The parameters that were explored were: types of screen surface (polyurethane, woven wire etc), types of screen motion (linear, circular or elliptical), angle of motion ( 40,45,55,60 degrees etc), and throw (amplitude), speed and 'g' force.

Jun 1, 2010

By H Holmstr÷m, A Widerlund, M Lindvall

At the Kristineberg mine in northern Sweden sulfide-rich, poorly buffered tailings have been deposited in five impoundments located along a valley. The tailings area has been remediated by applying a combination of till cover and flooding. A new method that has been applied to parts of the tailings area is to raise the groundwater table to saturate the tailings. By increasing pH by liming, thereby reducing metal mobility, a water-covered downstream impoundment is functioning as a trap for metals released from the till-covered impoundments upstream. In this paper the efficiency of the system approach used at Kristineberg is evaluated. Progressive changes of water quality from groundwater in the upstream till-covered impoundments via surface streams within the pond system to the water in the flooded downstream pond and its outlet are described. The results show that the system approach used in the design of the remediation programme of the tailings works as planned. The sulfide oxidation rate has decreased in the till-covered impoundments, and, as predicted, there is an out-flush of old weathering products which will continue for at least five years before equilibrium is reached. The groundwater in the till-covered impoundments has high concentrations of Fe, S, Mg and Zn, but the concentrations of metals such as Cu, Cd and Pb are much lower than before the till cover was applied. The limed pond is an efficient metal trap, with concentrations as high as 2.76 per cent Zn and 0.28 per cent Cu in the calcite-gypsum sludge developed on the tailings. The outlet from the flooded pond, and thus from the whole mining area, releases small amounts of metals to the recipient in comparison to the amounts that are in movement within the mining area. During the period May to November, 13 kg dissolved Zn and 111 kg particulate Zn was released to the recipient, whereas a total of 27 000 kg was transported by surface water within the impoundment system during the same period. The results from Kristineberg show that when planning remediation of complex mining areas, it is useful to adopt a system approach in which different methods are used on different parts of the area along the flow path of the drainage water, whereas flooding of the downstream pond is the key to the performance of the entire system.

Jan 1, 2003