Search Documents

By P. R. Smith, R. A. Walters

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915. In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various boiate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 122 m (400 ft) deep, 910 m (3000 ft) long and 305 m (1000 ft wide). The borates in the Boraxo pit consist primarily of three minerals. These are about 50% colemanite (CB6011 5H20), about 40% probertite (NaCaB50g 5H20), and 10% ulexite (NaCaBgOg 5H20). The colemanite, along with boric acid and high-grade colemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder, which is the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content, which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations. Laboratory Calcination and Air Tabling Tests Laboratory calcination tests showed that substantial upgrading of the borate could be accomplished by calcining followed by screening of the calcined material. Removal of the + 28 mesh calcine resulted in borate losses of less than 10% with a rejection of 40 weight % or more of the calcine. The minus 65 mesh calcine generally met the requirement of containing 48%, or more, B203. The minus 28 plus 65 mesh material contained an intermediate quantity of borate and would require additional treatment. Testing demonstrated that ore would not have to be reduced to a size finer than 19 mm (3/4 in.) prior to calcination. A temperature range from 400 to 455OC (750 to 850°F) was apparently satisfactory. Calcination at a temperature of 48Z°C (900°F), or higher, was unsatisfactory due to fusion. All laboratory calcination tests were static tests conducted by placing small covered charges in a laboratory furnace for 40 min. In all tests vapor issues from the furnace for 5 to 7 min. Following this period the ore could be heard "popping," due to decrepitation of the colemanite. The reaction generally continued for approximately one-half hour. Various size fractions of the calcination products from laboratory tests were subjected to laboratory air tabling tests, usually after removing the plus 28 mesh material. Laboratory air tabling tests were conducted employing a Whippet V-80 model air table manufactured by Sutton, Steele and Steele Co. now known as Tripple S Dynamics. Variables include both end and side-tilt, speed of vibration, and quantity of air rising through the deck. In addition to the variables in the machine itself, the feed rate is also a rather critical variable. Testing demonstrated that all - 28 mesh size fractions of the calcine could be successfully concentrated to 48% F2O3 or greater. For the finer material recoveries into the concentrate were between 85 and 90% of the borate. With the coarser material a substantial amount of middling was produced which required cleaner tabling. Laboratory calcination and air tabling tests indicated a process whereby the borate could be concentrated to about 50% B203 with borate recoveries approaching 90%. Moreover, the iron content of the concentrate was well below the required specification of 0.3% Fe2O3. Pilot Plant Calcination Following the laboratory test work described above, pilot plant testing was conducted to prove the process, provide data for engineering studies, and provide product for a prospective purchaser. The kiln used was 0.9 m-diam (3 ft) by 9.0 m (30 ft) long and had a belly section 1.2 m-diam (4 ft) by 2.74 m (9 ft) long near the discharge end. The kiln was operated at a speed of 0.7 rpm. Gas was fired into the kiln at an average rate of 27.1 m3/hr (958.4 cu ft per hr). The air to gas ratio used was 10:1. The ore was fed to the kiln countercurrent to the flame and discharged through a hopper into a screw conveyor which discharged to a 1.2 m (48 in.) Sweco separator. The separator had 28, 65, and 150 mesh screen cloths, with the plus 28 mesh fraction being discarded. The minus 28 mesh fractions were later subjected to air tabling. The exit gases, containing some calcine dust, were swept through two cyclones to recover the dust. The gases then were scrubbed in a Ducon scrubber; very little dust reported past the first cyclone. The dust from the first cyclone was also saved in drums. In addition to the gas rate, the flue gas velocity, after

Jan 1, 1981

(There are 67 Student Chapters in the United States, 2 in Canada ) University of Alabama-University, Alabama, Mining & Metallurgical Society, James W Stewart University of Alaska-College, Alaska, Mining Society of the University of Alaska, Guinn Metzger University of Arizona-Tucson, Arizona, Miners' Society, A E Gorum Birmingham-Southern College-Birmingham, Alabama, Pick & Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, A Gunning University of California-Berkeley, California, Mineral Technology Association, Bernard York Carnegie Institute of Technology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of Technology-Cleveland, Ohio, Pick and Shovel Club, Gerald M Cover City College of New York-New York, New York, CCNY Student Chapter AIME, Daniel T O'Connell

Jan 1, 1954

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970

In 1975, the US produced 10 900 tons (12,000 st) of U3O8 from ores whose grade ranged from a low of 0.160% to a high of 0.196% U3O8. By the early 1980's if the current mining projects described here are allowed to go on stream, Australia will be able to produce at least 10 900 tons of U3O8 annually from ores whose grade ranges from a low of 0.150%to a high of 2.300%. As pointed out in the previous article, this initial rate of production could have been reached now-giving an immense boost to the depressed Australian economy. So, let's have a close look at current mining projects.

Jan 1, 1977

MARCH 15-Industry is rapidly snapping back from another coal crisis, other business news is in general favorable and the outlook through the Spring is by most observers considered quite promising. Most industries report comfortable backlogs of unfilled orders, department store sales in recent weeks have equalled in dollars those of the corresponding period last year, retail sales of automobiles show again over the same period a year ago, and new orders for machine tools are at the highest figures since August 1946. Orders for railway freight cars have shown a very encouraging pickup, with a total of 9385 cars in January and the N. Y. Central alone ordering 4500 in February. Construction continues very active. In January new housing starts totaled 80,000 against 50,000 a year ago and the daily average contract awards, according to the Dodge reports, were 57 pct larger. In the first 22 days of February the increase in awards was 27 pct. Lumber orders since Jan. 1 have run 22 pct above last year. All of these favorable factors bolster the opinion that the upturn in industrial output and employment which began last summer has not yet spent itself and that the setback caused by the strikes will be made up when people get back to work. Only in a few lines are there indications that primary production may be outrunning the consumption of finished goods, although inventory build-up would seem to be rather modest as the National Association of Purchasing Agents reported in February that 78 pct of its members were buying for 60 days or less. Industrial prices as a whole show no significant trend despite the continued alarm over both the immediate and the long-term possibility of inflation caused primarily by the government's increasing expenditure and its inability to balance the budget. A recent advance of 1.9 pct in primary market prices is viewed by some people as the surface symptom of renewed inflation, but even so it is more than two years since the alltime high was reached by the daily index of sensitive commodities in November 1947. Over two years have passed since prices received by farmers hit their peak and about a year and a half since all wholesale prices and the consumer price index touched their highest points in August 1948. The decline in the wholesale price index has been almost continuous, interrupted only twice by slight advances in the monthly figures from February to March 1949, and, later in the year, from August to September. Of course, this continued decline in the last half of 1949 largely reflects a downward movement in farm and food prices. Wholesale prices for commodities other than farm and food leveled out after June and now stand only slightly under the June level. Farm products are down by 22 pct from January and by 18.6 pct from August 1948. Food prices are down only slightly less. Consequently, the farm price support program is in serious trouble and has imposed a heavy financial burden on the Treasury. In those commodities other than farm products only building materials, chemicals and textiles have come down as much as the average, while housefurnishings and metals and their products have fallen hardly at all. Glancing away from the domestic front, the results of the British general election indicated a highly inconvenient situation, that public opinion there is so exactly deadlocked as to divest the victors of much ability to make forceful decisions or create significant policy. It is generally considered that another election in the near future would give substantially the same result. The British people are equally divided and the politicians are not likely to precipitate another appeal to the country until there is manifest reason to believe that external and internal circumstances have changed sufficiently to permit one party or the other to obtain a decisive verdict. Because of the lack of a clear mandate steel nationalization will likely lag in Britain. In the meantime there is considerable discussion going on as to whether the European steel industries as a whole are at a disadvantage in world competition with the American industry. An article in the "Statistical Bulletin" for January of the British Iron and Steel Federation takes issue on this point with the authors of the Geneva report, observing that they wrote before devaluation, and this particular conclusion "has been overtaken by events." The "Bulletin" also contends that the statement was in any case incorrect so far as Britain was concerned, and that it was based on scanty and insufficient evidence. To support the rebuttal a detailed and extensive comparison is made of the home prices of certain steel products in Britain and in other countries of the world. The accompanying table gives a selection of the prices published. It sets out the changed position since devaluation and since the recent increases in American steel prices. These are home market prices; no doubt in competitive export business some of the price levels could be brought closer together at need.

Jan 4, 1950

A letter from Mr. E. F. Cykler, Secretary-Treasurer, informs us that the Engineering Societies Club of Hawaii has been established, and that a member of any one of the following organizations is eligible for membership in the Hawaiian club: American Society of Civil Engineers, American Society of Mechanical Engineers, American Institute of Mining Engineers, American Institute of Electrical Engineers, American Society of Naval Engineers, American Railway Engineering Association, American Society for Testing Materials. The main purpose of this club is the entertainment of visitors from the various national organizations above mentioned, and the Secretary will be glad to hear from any one who is making a trip to the Hawaiian Islands. Mr. Cykler's address is 2A Pantheon Building, Honolulu, Hawaii.

Jan 12, 1917

By John P. Weir

Coal's participation in the domestic energy market depends to a very large extent upon the cost of coal delivered to consumers. Today the principal use of coal in the U.S. is in steam-electric generating stations. Generally, it is the delivered cost per million Btu's that is given the greatest weight in choosing either oil, natural gas or coal as the fuel used in these power plants. There are three major cost components of generating electric energy in steam-electric plants. These expenses expressed in terms of "dollars per kilowatt year" are: (1) operation and maintenance of necessary facilities, (2) fixed charges of necessary capital investment, and (3) fuel. For a modern large plant, the first two items would be approximately as follows:

Jan 9, 1962

By Zhu Weishen, Xu Dongjun

In the 1st part of this paper a comparassion of the different methods for determining the modules of elasticity and deformation of hard rock is made. It is found that the plate bearing method has a serious shortcoming. The slit flat-jack method seems to be a mare reasonable technique, which is recommended as a desirable method for in situ testing. In the 2nd part, a new test method to determine the properties of deformation and strength of weak plane in rock mass is recommended. Then the relation of weak plane character to the character of stress-strain curve, the relation of normal stress to the character of shear displacement curve and the yielding criterion of weak plane are discussed.

Jan 1, 1982

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven't to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

By Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (I), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profit- ability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus mini- mum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12 ) Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-low- grade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1985

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By J. H. Jackson, P. D. Frost, C. H. Lorig, L. W. Eastwood, A. C. Loonam

It is well known that for equal weights of material, thin sections of the lighter structural alloys are more resistant to buckling under a compressive stress than thin sections of more dense material. Therefore, structural parts having the same resistance to buckling stresses are generally lightest when they are made of magnesium alloys. Consequently, there is considerable interest in the development of strong alloys having densities equal to or lower than that of magnesium and strength-weight ratios equivalent to those of the strongest aluminum alloys. The development of commercial magnesium-base alloys has been very successful, and their importance among materials in the structural field has been amply demonstrated. However, an even wider structural application of magnesium alloys might be effected if improvements could be made in the cold rollability and cold-forming characteristics. Such improvements, along with production of less directionality in properties. could be effected if the hexagonal close-packed lattice of present alloys could be replaced with a cubic lattice. In 1942, a project, having as its objective the improvement of some of the characteristics of commercial magnesium-base alloys, was initiated at Battelle Memorial Institute under the sponsorship of the Mathieson Chemical Corporation. At that time, one of the authors,* then Chief Metallurgist for the Mathieson Chemical Corporation, postulated that the addition of lithium to magnesium in sufficient quantities to change the crystal structure of the resultant alloy from a hexagonal to a body-centered cubic lattice should produce a magnesium-rich alloy which would have the desired improvements in cold-working characteristics with less directionality in properties. To test this view, a series of alloys was made and was found to have many of the attributes that were predicted. The view that magnesium-lithium alloys were of structural interest was also held by others. In 1943 and 1945, Dean and Andersonl,² obtained patents on magnesium-base alloys containing from about 1 to 10 pct lithium, from about 2 to about 10 pct manganese, and the balance substantially all magnesium; and on magnesium-base alloys containing from about 1 pct to about 10 pct lithium, from about 2 to about 10 pct manganese, from about 0.5 to 2 pct silver, and the balance substantially all magnesium. They noted that an alloy containing 83 pct magnesium, 10 pct manganese, 5 pct lithium, and 2 pct silver could be cold rolled by any of the usual methods and that this alloy was considerably harder and stronger than most other magnesium-base alloys heretofore available. In 1945, Hume-Rothery, et al.,3 predicted that magnesium-lithium base alloys should be soft and ductile and that such compositions, to which was added a third element for the purpose of producing a precipitation-hardening type of alloy, should be ductile, strong, and lighter than magnesium itself. Hume-Rothery investigated the binary magnesium-lithium and ternary magnesium-lithium-silver equilibrium relations and criticized the existing equilibrium diagrams. The binary magnesium-lithium equilibrium diagram has also been investigated by Grube, Von Zeppelin, and Bumm, Henry and Cordiano, Sal'dau and Shamrai, Hof-mann,' and Shamrai.8 The work of most investigators agreed with that of Grube, whose constitution diagram is shown in Fig 1. From the standpoint of development of structural alloys, the room-temperature equilibrium relations are of great interest. An examination of Fig 1 reveals that, from 0 to 5.7 pct lithium, the existing phase is alpha, which is a solution of lithium in hexagonal magnesium. The boundary between the alpha, and alpha plus beta regions, occurs at a Mg/Li of 16.5, corresponding to 5.7 pct lithium by weight. Between 5.7 pct and 10.3 pct lithium, there exists a mixture of the alpha phase (lithium dissolved in hexagonal magnesium) and the beta phase (magnesium dissolved in body-centered-cubic lithium). The boundary of the alpha plus beta and beta regions occurs at a Mg/Li of 8.7, corresponding to a lithium composition of 10.3 pct. Much of the work described here was directed toward obtaining an alloy made up of a large proportion, or entirely, of the body-centered-cubic beta structure. In his early work, Loonam found that specimens of lithium-bearing alloys were very malleable. Ingots of alloys prepared at that time were extruded to 3/8-in. diam bars, and the mechanical properties and the effects of heat treatment were then determined. These data are given in Table 1. The outstanding ductility of the alloys, combined with their moderately high strength, evoked considerable interest.

Jan 1, 1950

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.&apos; Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

By W. G. Pfann

In zone-melting, a small molten zone or zones traverse a long charge of alloy or impure metal. Consequences of this manner of freezing are examined with impurerespect to solute distribution in the ingot, with particular reference to purification and to prevention of segregation. Results are expressed in terms of the number, size, and direction of travel of the zones, the initial intermsofsolute distribution, and the distribution coefficient. IF a charge of binary solid-solution alloy is melted and then frozen slowly from one end, as for example in the Bridgman method of making single crystals,&apos; coring usually occurs, with a resulting end-to-end variation in concentration. Such coring, or normal segregation, is undesirable where uniformity is an object. On the other hand, for certain systems, it can be utilized to refine a material by concentrating impurities at one end of the ingot.&apos;. &apos; In the present paper a different manner of freezing will be examined with respect to the distribution of solute in the ingot. A number of procedures will be indicated which have in common the traversal of a relatively long charge of solid alloy by a small molten zone. Such methods will be denoted by the general term zone-,melting, while the process described in the preceding paragraph will be called normal freezing. It will be shown that, in contrast to normal freezing, zone-melting affords wide latitude in possible distributions of solute. Segregation can either be almost entirely eliminated or it can be enhanced so as to provide a high degree of sttparation of solute and solvent. A number of simplifying assumptions will be invoked which, while not entirely realizable in practice, nevertheless provide a suitable point of departure for more refined treatments. Moreover, our own experience with zone-melting has shown that, for certain systems at least, the analysis holds quite well. The present paper will be confined to a discussion of principles and a general description of procedures. Comparison with experiment is planned for later publication. Normal Freezing Before considering zone-melting, segregation during normal freezing will be reviewed briefly. If a cylinder of molten binary alloy is made to freeze from one end as in Fig. 1, there usually will be a segregating action which will concentrate the solute in one or the other end of the ingot. If the constitutional diagram for the system is like that of Fig. 2, then the distribution coefficient k, defined as the ratio of the concentration in the solid to that in the liquid at equilibrium, will be less than one and the solute will be concentrated in the last regions to freeze. If the solute raises the freezing point, then k will be greater than one and the solute will be concentrated in the first regions to freeze. The concentration in the solid as a function of g, the fraction which has solidified, can be expressed by the relation: C = kC0 (1-g)k-1 [I] where C, is the initial solute concentration in the melt. Eq 1 is based on the following assumptions: 1—Diffusion in the solid is negligible. 2—Diffusion in the liquid is complete (i.e., concentration in the liquid is uniform). 3—k is constant. Concentration curves representing eq 1 for k&apos;s from 0.01 to 5.0 are plotted in Fig. 3. This equation, in one form or another, has been treated by Gulliver,³ Scheuer,4 Hayes and Chipman5 for alloys and by McFee2 for NaCl crystals. It is derived in Appendix I. It should be pointed out that the k which is calculated from the phase diagram will be valid only in the ideal case for which the stated assumptions are correct. In all actual cases, the effective k will be larger than this value for solutes which lower the melting point, smaller for solutes which raise the melting point, and will probably vary during the beginning of the freezing process. For simplification it will be assumed that the ideal k is valid. Zone-Leveling Processes The processes of this part are designed to produce a uniform, or level, distribution of solute in the ingot. Single Pass: Consider a rod or charge of alloy whose cross-section is constant and whose composition, C2, is constant, although permissibly varying on a microscopic scale." Such a charge might be a rapidly frozen casting or a mixture of crushed or powdered constituents. Cause a molten zone of

Jan 1, 1953

By P. E. Rider, K. A. Gschneidner, O. D. McMasters

The solid solubilities for thirteen rare-earth metals in gold were determined by using the X-ray parametric method. Solubilities ranged from 0.1 at. pct for lanthanum in gold up to 8.8 at. pct for scandium in gold. The solubilities from lanthanum to gadolinium were very small and essentially constant, but a sharp increase occurred from gadolinium to scandium. The large solubilities for the heavy rare-earth metals were not expected because of the large size and electrochemical differences between rare-earth atoms and the gold atom. Contributions from first- and second-order elasticity theory plus an electronic contribution were found to reasonably account for a more favorable size factor. Electron transfer from the rare-earth metal to the gold Is thought to occur such that the resultant rare-earth and gold electronegativities are favorable for solid-solution formation. It was also found that this mutual adjustment of size and electronegutivity does not occur if the pure-metal size factors are greater than a critical value of 25 pet. The eutectic temperatures for ten systems were determined and these remained fairly constant at approximately 809 "C for the lighter lanthanide metal-gold systems until the Er-Au system was reached, at which Point the eutectic temperature successively increased reaching a maximum of 1040°C in the Sc-Au system. This rise was correlated to the size factor becoming more favorable for solid-solution formation at erbium. The valence state of ytterbium was found to change from two in the pure metal to three when ytterbium is dissolved in the gold matrix. RECENT results1 reported concerning the solubility of holmium in copper, silver, and gold, showed that the solubility of holmium in gold was quite large, 4.0 at. pct, compared with 1.6 in silver and 0.02 in copper. The small solubilities of holmium in silver and copper are quite reasonable in view of the large size difference (22.2 and 38.2 pct, respectively), large electronegativity difference (0.59 for both systems), and possible unfavorable valency factor (assuming one for silver and copper and three for holmium). The large solubility in gold, however, is unexpected because these same factors are also unfavorable for holmium and gold (22.5 pct size difference and 0.69 electronegativity difference), and because the light rare-earth metals, lanthanum, cerium, and praseodymium, have negligible solid solubilities in gold.2 In view of this unexpected behavior, it was felt that a study of the solid solubilities of most of the rare-earth metals in gold would be desirable to better understand the factors involved in the formation of solid solutions. Of the rare-earth metals added to gold in this study, only ytterbium is divalent in the pure metallic state (the other rare-earth metals are all trivalent) and many of its physical properties (such as the metallic radius, electronegativity, and so forth) are much different from those of the normal trivalent rare-earth metals.&apos; The properties of ytterbium are such that one would expect solid-solution formation to be less favorable for ytterbium in gold than for any of the normal trivalent rare-earth metals. But chemically ytterbium is known to possess a stable trivalent state, and it is quite possible that ytterbium may alloy as a trivalent metal under certain conditions rather than as a divalent metal. Because of the dual valency nature and because so little is known about the alloying behavior of ytterbium, the gold-rich ytterbium-gold alloys are of special interest. EXPERIMENTAL PROCEDURE Materials. The gold used in this investigation had a purity of 99.99 pct with respect to nongaseous impurities. In general the rare-earth metals were prepared by reduction of the corresponding fluoride by calcium metal.3 The impurity contents of the metals used in this study are given in Table I. Preparation of Alloys. Two- or 3-g alloy samples were prepared by arc melting. The samples, with the exception of some of the Er-Au alloys, had weight losses of 0.5 pct or less. All alloy concentrations noted in this paper are nominal compositions. After arc melting, the alloys were wrapped in tantalum foil, sealed off in quartz tubing under a partial atmosphere of argon, homogenized for approximately 200 hr at 780°C, and then quenched in cold water. X-Ray Methods. The X-ray parametric method was used in determining the solubility of the rare-earth metals in gold. filings were sealed in small tantalum tubes by welding under a helium atmosphere. The tantalum tubes were then sealed in quartz tubing under a partial argon atmosphere, and annealed for times ranging from 1/2 to 3 hr (the length of time was inversely proportional to the an-

Jan 1, 1965

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.&apos; I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker&apos;s hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By J. R. Elenbaas, J. A. Vary, D. L. Katz

The development of gas fields, oil fields and aquifers for storing natural gas is treated from two main vieu.-points: (I) the volumetric storage capacity for gas in a given situation and (2) the prediction of the number of wells required for the delivery of gas. Other experiences in the design and operation of storagc fields are incluclerl INTRODUC TION Storage of natural gas in underground reservoirs near the terminus of long distance pipelines has been the prime factor in opening the space heating market to the natural gas industry. Storagc has permitted a major. increase in both the load and the load factor of pipe-lines; some are now operating at steady load throughout the year. Thus, underground storage has been responsible for the rapid increase in demand for natural gas in recent years. Three types of reservoirs have been used for gas storage: natural gas reservoirs, oil reservoirs, and waterbearing sands or aquifers. This paper presents the factors to be considered when developing gas storage reservoirs of these three categories. There are two prime considerations tor any storage reservoir: (1) the volume of gas which a given reservoir will store advantageously and (2) the number 01 wells needed to provide the required peak deliverability. These two problems will be considered for the three types of reservoirs just noted STORAGE IN PARTIALLY DEPLETED GAS FIELDS Early storage operations consisted of replenishing the natural gas in a depleted gas field situated adjacent to the market. Today, newly discovered fields near the market may be considered for storage, and this discussion applies equally to both types of reservoirs. For reservoirs originally containing gas or oil, the question of the impermeability of the cap rock nor-mally does not arise. However, such fields are likely to have many wells drilled either to or through the reservoir under consideration. Positive assurance must be obtained that such wells are or can be made mechanically tight. Corroded casings may need to be lined or permanently plugged. Abandoned wells should bc reopened and properly cemented. The volumetric capacity for gas storage depends upon space available in the porous rock as well as pressure and temperature of the gas in the reservoir. The production-pressure decline data on partially depleted gas reservoirs without water drive permit calculation of the reservoir space for gas. Isopachous maps of sand volume and porosity data for the reservoir rock provide an alternate method of calculating the pore volume for water-drive reservoirs. The pressure range selected for the storage cycle depends upon ()) the safe upper limit of pressure. 2) the flow capacity of wells and (3) compression requirements when injecting gas into the reservoir or delivering to market. Normally, gas and oil fields have pressures at discovery in the range of 0.43 to 0.52 psi/ft of depth. Pressures of around 1.0 to 1.2 psi/ft of depth appear to lift the overburden1-3 and invite uncontrolled movement of fluids in the porous rock. Some top pressure is normally selected for a storage reservoir ranging from below discovery pressure for deeper reservoirs to 0.65 psi/ft of depth for shallower reservoirs. Pressures to 0.66 psi/ft have been experienced without difficulty. The lower pressure limit is set by water intrusion accompanying low pressures, reduced flow capacity for wells at lower pressures and compression requirements. Depletion-type gas reservoirs often encounter water problems in the later stages of gas production. Such water intrusion may be due to movement from the surrounding aquifer. Accordingly, displacement of this water back into the aquifer by gas pressure and subsequent surges of water corresponding to the gas storage pressure cycle must be considered. Storage fields often produce in four months a volume of gas equal to its initial content. Rapid decreases in reservoir pressure occur, such as 20 psi/day. Accordingly, closed-in pressure observation wells which reflect the pressure in the bulk of the reservoir are required for following the operation of the reservoir. It has been found that a plot of observation wellhead pressures against gas content, Fig. 1, is very useful in observing operation of the field, checking the inventory and predicting future behavior. The plot is based on a given quantity of base or cushion gas in place. The injection and withdrawal curves may spread depending upon the homogeneity of the reservoir rock. permeability of the rock, well spacing and flow rates.