Search Documents

By E. J. Dulis, R. M. Fisher, K. G. Carroll

IT is well known that ferritic steels containing more than 15 pct Cr when subjected to temperatures in the range of 700" to 1000°F exhibit increasing hardness and decreasing ductility. The phenomenon has been widely termed the "885 °F embrittlement," after the temperature of most marked effect.'.' In view of the excellent review articles available in the literature3-6 only a brief account of experimentally established facts need be given here. The extent of changes in physical characteristics during embrittlement depends on chromium concentration and time at temperature, higher alloy content and longer time both promoting more rapid and extensive changes. In a 27 pct Cr steel, changes in impact strength and in angle of fracture in bending can be detected after only a 1 hr exposure at 885°F; after 50 hr this steel becomes quite brittle. Hardness increases slowly with time during thousands of hours exposure and may attain a maximum hardness number twice as large as that of the unexposed steel. Microstructural changes accompanying embrittlement have been described as an initial widening of grain boundaries followed by eventual darkening of ferrite grains. Embrittled steels etch more readily, e.g., the weight loss of a 27 pct Cr steel in acid solution may occur at a rate one hundred fold greater following exposure at 885 OF. Marked changes which accompany embrittlement have been observed in electrical resistivity, specific gravity, and magnetic coercive force. Changes in physical properties may be readily removed by heating at temperatures above the embrittling range, such as a treatment at 1100°F for 1 hr. It has frequently been noted that the 885 °F embrittlement suggests precipitation on a submicro-scopic scale of a chromium-rich constituent, the nature of which has not been revealed by X-ray diffraction. Progressive broadening of the body-centered cubic diffraction lines during embrittlement has been observed," and recent observations by Lena and Hawkes' upon single crystals have shown early asterism in X-ray photographs, disappearing within an hour at 900 °F. Many workers have ascribed8-13 the phenomenon to a precipitation of a phase (FeCr), which is known to cause embrittling effects at temperatures much higher than 885°F. Two general observations, however. suggest that a precipitation cannot be responsible for the 885°F phenomenon: 1—prior cold work greatly enhances a formation, whereas it scarcely affects the 885 °F embrittlement, and 2—the presence of an alloying element such as nickel or manganese may have an effect on the 885 °F embrittlement which is opposed to its effect upon a formation. The slight enhancement of a formation and 885°F embrittlement observed in the presence of elements with strong carbide and nitride forming tendencies' is probably a consequence of lessened chromium depletion of the matrix. The bar graph in Fig. 1 shows a typical example, taken from two 27 pct Cr steels used in this work, of the hardness after exposure for 10,000 hr at 900°, 1050°, and 1200°F. Steel A (0.03 pct C, 3.13 pct Mn) showed marked hardening at 900" and 1200°F, whereas steel B (0.12 pct C, 0.63 pct Mn) exhibited only the 900°F hardening. The cr phase was found in steel A at the higher temperatures but not in steel B. Presumably a formation is enhanced by the low-carbon and high-manganese concentrations in A," Thus there are two distinctly different hardening phenomena present which cannot both be ascribed to v precipitation without invoking a transition phase possessing remarkable properties. Materials A number of chromium steels exposed for long periods (5000 to 34,000 hr) at 900°F, as well as unexposed samples of one of the steels, were available for this investigation. Table I gives the chemical compositions and aging treatments of these steels. In addition to these steels exposed in the elevated temperature test furnaces of the National Tube Division, a number of high-chromium steels were heated for short periods in small laboratory air furnaces and lead baths. Supplementing these commercial steels, a sample of high-purity (0.018 pct C, 0.002 pct N) 28 pct Cr iron, exposed 1000 hr at 887°F. was furnished by the Union Carbide and Carbon Corp. In addition, an alloy of iron and chromium of high purity containing 46 pct Cr was used. This

Jan 1, 1954

By J. G. Balkestein, J. W. R. Baerts

During an attempt to develop a method for accurate, rapid, continuous analysis of ash content of wal, the Dutch State Mines Laboratory found that the absorption coefficient for X-rays was related to ash content. This relationship was utilized in the development of an apparatus called CendreX, used to measure the absorption and in turn the ash content. The principle, procedure, accuracy, and applications of the CendreX automatic determination of ash in coal are discussed in detail. Until recent years coal preparation research was concentrated on the possibilities and efficiency of preparation equipment. Ever increasing demands for quality in coal, however, have caused researchers to become concerned with quality control. One of the characteristics strongly influencing quality (calorific value) and, consequently, the price of coal is ash content. Both customer and producer require that the ash content be controlled. To make this possible it is necessary for the producer to collect samples from the coal stream in the washery and to determine their ash content. On the strength of the results obtained the production process can then be adjusted, if required. Until recently incineration was the only method for determining ash content. When coal is incinerated with oxygen, it takes at least 15 min to determine the ash content. Even then some time may be lost in passing on the data. Therefore, this discontinuous and time-consuming method does not make a suitable starting point for checking, re-adjusting, or modifying the production process. Since it was not possible to accelerate incineration by mechanization and automation, another type of rapid continuous analysis had to be found. This would have to depend on some coal characteristic closely linked with ash content. At the Central Laboratory of Dutch State Mines, Dijkstra and Sieswerda found that the absorption coefficient for X-rays was suitable for this purpose. An apparatus based on the measurement of this characteristic was developed. Named CendreX,* this patented equip- *A Stamicarbon N. V. registered trademark. ment, used in combination with a sampler and conditioning apparatus, permits continuous determination of ash content with satisfactory exactness to within 3 min.t At the American Mining Congress meeting of May 1961, Log A. Updegraff, surveying aspects of continuous analyaia, reported on the CendreX appartus (Mining Congress Journal, August 1961). Since the first Condition for correct ash determination, whatever the method used, is always a sample taken in the right way, some practical aspects of sampling will be discussed first. SAMPLING In coal handling operations, each grain has its characteristic properties. In both the cross-sectional and longitudinal direction of the product stream the mixture of these grains is imperfectly blended. The elimination of the factor of segregation between the cross-sections from the direction of the stream is the principal aim of continuous analysis. Therefore, the samples to be analyzed are withdrawn in various places from the segregated product stream in such a way that they form a semi-continuous flow. In order to be truly representative of the product stream, the sample flow must fulfil two conditions: 1) The sample flow must be sufficiently large to insure that adventitious differences between the composition of the product stream and sample flow will be as small as possible. 2) All grains through the entire cross section of the product stream must have an equal chance to get into the sample flow. Since there is always a segregation through the cross section the sample flow will have a bias if the sampler collects only part of this section. In order to prevent the volume of the sample flow from becoming too large, the cross sections are taken discontinuously. However, this discontinuity gives rise to the adventitious differences that arise between the composition of product stream and the sample flow, and these differences become greater and are more deranging as the fluctuations follow each other more quickly. Moreover, the intervals between the morrnents of sampling mean a delay in the analysis. The aim will, therefore, be to collect small samples, or in other words thin cross-sectional increments, taken at sufficiently high frequencies. The following points should also be taken into account: 1) The smallest dimension of the openings in the sample collector must be equivalent to at least 3 d in

Jan 1, 1962

By N. J. Grant, D. S. Bloom

N recent reports, Sully' and Beck and coworkers' I have advanced hypotheses concerning the formation of the phase. Both of these hypotheses are based on Pauling's theories of the electronic configuration of the elements of the first transition group. Sully considered that the number of electrons which can be absorbed in filling electron "holes" is the factor which determines whether or not the structure can form. Beck suggested that the presence of a certain concentration of electron "holes" is the controlling value. It can be shown that a similar criterion can be developed without making reference to Pauling's theories. Table I shows the elements of the first transition group and the incidence of the a structure in the binary systems of these elements according to the data presently available. Also appended is the number of electrons considered to exist in the 3d-4s levels of these elements. If the atomic percentages for the phase are listed as shown in Table 11, and if the number of electrons in the 3d-4s levels per atom is calculated for the a boundary values, the results are as shown in the last column. It can be seen that the numerical values are all in the vicinity of 7 electrons per atom. This is true also for the ternary Cr-Mo-Ni IT phase, which occurs in a system in which none of the binary compositions are known to develop the phase. In the Fe-Mo binary, the high temperature a phase, which occurs at a composition of 50 atomic pct of each element, also yields a ,;1 e of 7 electrons per atom. From inspection of Tables I and 11, it develops that any series of sequential numbers which is assigned to the elements under consideration will result in the numbers pertaining to a compositions grouping themselves around one specific number. It does not follow, however, that this random number necessarily has physical significance. Such a point has already been discussed by Hume-Rothery." One interesting point develops from this study, however, and that is the position of manganese with reference to the other elements and to the phase. In the system used here, the formation of phase is associated approximately with the value of 7 electrons per atom, which is also the number of electrons per atom that manganese has. Manganese, it will be recalled, exists in three different crystal forms, none of which are the usual, simpler metallic forms; on the other hand, elements just to the left of manganese (in Table I) generally have lower coordination-number structures (body-centered cubic) than do elements to the right of manganese (face-centered cubic). The contribution to a complex crystal structure by the interalloying of elements from opposite sides of manganese is significant in that the a phase is formed in binary systems including one element from each side of manganese, with manganese capable of participating with both sides. It is indeed an interesting coincidence that manganese, with 7 electrons per atom, solidifies in complex crystal forms, and that when alloys of the transition elements are made which have seven 3d-4s electrons per atom, they, too, tend to assume a complex crystal form. From the above, it might be deduced that the study of the a phase might be advanced by a critical examination of the element manganese and how its structure is affected by small additions of elements which change the 3d-4s electrons per atom number. The role of atom size would also be of interest in formation. References ' A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, Part 4, p. 173. 2 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951). "W. Hume-Rothery, H. M. Irving, and R. J. P. Williams: The Valencies of the Transition Elements in the Metallic State. Proc. Royal Soc. (September 1951) 208A. p. 431.

Jan 1, 1954

By Claiborne C. Van Zandt

THE heavy postwar demand for Portland Cement has created shortages that are gradually being overcome by increases in plant capacity. In the post-war period, the Lone Star Cement Corp. has expanded several of its existing 15 plants and has built 2 new plants, now in operation, with a third new plant under construction in Brazil, of design somewhat different from that of the two preceding ones. The new domestic plants are located at Lone Star, Va., near Roanoke, and at Maryneal, Tex., near Sweetwater, and went into operation during 1951. Each plant is equipped with two rotary kilns and has an initial capacity of 1,500,000 bbl per year, or 6,000,000 sacks. The total cost of each plant was about $10,500,000, and on this basis $7.00 in 1951 money are required per bbl of annual capacity; at 376 lb per bbl, this corresponds to $37.00 per ton of output. The investment corresponds to approximately $80,000 per hourly-wage earner employed. The purpose of this paper is to describe the most interesting design features of the two new and almost identical Lone Star plants. Why the Dry Process Was Chosen The two new domestic Lone Star mills employ the dry process because: 1-The raw materials at both properties are particularly suitable and can be dried very, readily. 2-The Maryneal, Tex., plant does not have water available for slurry. 3-Very substantial kiln fuel savings can be obtained. 4-Dry raw grinding reduces ball and liner wear and- general maintenance, without any sacrifice in power. Operating costs to date have more than justified the choice of the dry process for these two plants. Raw Materials The chemical composition of Portland Cement raw material after crushing, grinding, and mixing, but before burning, is about as follows: [ ] sometimes tailings from an iron ore concentrating plant. Certain objectionable materials occur in raw mix: magnesia, limited in cement to 5 pct, in excessive amounts; alkalies, as sodium and potassium; phosphorous; and sulphur, generally present in coal and oil. The Roanoke raw, materials are dense limestone and shale. The Maryneal materials are soft limestone and a hard brittle clay that can be handled much like shale. Sand and iron ore are required in small quantities. General Plant Layout and Construction The two plants are so similar that one joint description will cover both, with such exceptions as will be especially indicated. The crushing plant is located in the quarry, and raw material is conveyed by belt to the storage building, where all materials are stored and handled. Fig. 1 identifies the various structures of the Roanoke plant. The large storage building is used for the storing and handling of all materials, including limestone, shale, sand, iron ore, coal, clinker, and gypsum. Directly adjoining the storage building is a structure under a similar arched roof, containing the raw and clinker grinding departments and the electrical substation. The discharge ends of kilns and coolers, and coal or gas burning equipment are also placed at one end of the mill building. The 340ft long kilns extend away from the main buildings to form the long leg of an L, at the end of which is the feeding and kiln dust collecting equipment, and the raw blending silos are conveniently located adjacent to the feed end of the kilns. The machine shop, storeroom, electrical shop, foremen's office, service rooms, and meeting hall are combined in one structure in the center of the plant, and the office and laboratory are close by. The cement silos and packhouse do not have to be tied directly into the manufacturing process and are therefore located at a point convenient to the railroad tracks.

Jan 1, 1952

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark' at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark's experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By JOHN R. SUMAN

TONIGHT I want to speak of the current problems and the postwar difficulties facing American industry. American industry has done an outstanding job in adjusting its operations to wartime necessity. The national income for 1942 was nearly $120,000,090,000 and of this outlay approximately $55,000,000,000 went for war material. The enormity of the expenditures for war material is indicated by the fact that the expenditures for war purposes alone were greater than the annual gross national income in the period 1931-34. This tremendous production job in turning out a record output of war products was accomplished by industry in spite of a large number of restraining and hampering influences, and I want to mention several of the more important problems.

Jan 1, 1943

By Henry G. Morris

The use of compressed air for the transmission of power has reached so great a development that we find numerous large establishments devoted to the manufacture of machinery for its production and application, and special periodicals published for the dissemination of information on the subject. Moreover, its employment is so general in mining operations that no apology is needed for the presentation to the Institute of such a paper as the present. The admirable articles of Mr. E. A. Rix, published in Conzpressed Air, show a wide range in the mechanical efficiency of air-compressors, varying, under different conditions, from 15 to 60 per cent.; and it is evident that any

Jan 1, 1902

By G. Thomas, O. Johari

MEIERAN and Richman' have proposed a method for the determination of electron-diffraction patterns from twinned bcc crystals. It is the purpose of this note to present a general method capable of predicting the positions of all reflections from both matrix and twin regions for all possible orientations of cubic crystals. The method has been verified for twinning in explosively deformed copper, and is found to be a very useful tool when used in conjunction with stereographic projection, and dark-field electron microscopy. Let an isometric crystal be twinned in any (hkl) plane. The twinning can be considered either as a reflection in the twin plane or as a 180-deg rotation about the twin axis. In reciprocal space, the 180-deg rotation about the twin axis would place a given point p, q, Y to a new position P, Q,R, such that both will be equally inclined to the twin axis. This is represented in Fig. 1. If the coordinates of three such pairs of points are determined, the matrix of the transformation can be obtained.' It is also seen that such pairs would satisfy another condition, i.e., the vector [p,q,r] plus the vector [P,Q,R] will yield a multiple of hkl, i.e., the indices of the twin plane, because in isometric systems the axis [hkl] is perpendicular to the plane (hkl). This can be simplified by taking the points along the three axes. If a point h2 + k2 + 12, 0, 0 is taken along the x axis, it is seen that its new indices should be so as to yield a sum 2h2, 2hk, 2hl,i.e., 2h(h,k,1). (Also the points h2 - k2 - 12, 2hk, 2h1, and h2 + k2 + 12, 0, 0 are equidistant from the origin and both points make equal angles with the twin axis, i.e., cos-' h/dh2 + k2 + l2.) Similar operations for the points yield respectively, after the 180-deg rotation about the twin axis. Following the method due to Buerger,' the matrix of the transformation is obtained as follows: Using this matrix the indices of any other point in reciprocal space can be determined. This matrix is much simplified for (111) twinning commonly encountered in fcc metals, since are each equal to —1; hence

Jan 1, 1964

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

By GILBERT E. SEIL

GREAT advances in the preparation of ores for reduction to ferro-alloys have been made, although standard methods of reduction have been continued at most plants. Efficiencies, yields per furnace, and energy requirements per ton are generally better than previously attained. The advantages of sizing and conditioning of ore, fluxing stone, and coke have been realized. Conditioning varies from drying the furnace burden to chemical rearrangements to facilitate reduction reactions and sometimes to furnish some of the energy required for the reaction before the burden reaches the furnace. During the war period it is impossible to discuss in detail many of the advances made. They are subjects for postwar papers. However, the new procedures mentioned in the following paragraphs are indicative of the work already done and in progress.

Jan 1, 1944

By B. R. Hollebone

The chemical action of molten anhydrous pyridinium chloride (pyridine hydrochloride) on oxy salts and ores of some Group IV and V metals are discussed-in particular zirconium, hafnium, niobium (columbium) , and tantalum. Laboratory-scale experiments are described whose results suggest that this reaction might provide a practicable means of converting ores of these metals to the anhydrous metal chlorides. Experimental results are given which provide some insight into the nature of the reactions and some of the compounds which could be present at intermediate stages. The treatment of ores of the more refractory metals is difficult and expensive and often demands the use of gaseous chlorine, hydrogen fluoride, or other reagents which are, if nothing else, expensive and dangerous to use. This situation is, of course, due to the strong metal-oxygen affinity resulting from the high charge and the small size of the metal ion which combine to produce such high lattice energy in the metal oxide as to defeat standard reduction methods. Thus, the characteristic of these metals which leads to one of their most important properties—corrosion resistance—is the main hurdle in obtaining the metal. Many common methods' for treating ores of zirconium and niobium (columbium), for example, proceed as directly as possible to the preparation of anhydrous halides. These halides are purified by now standard processes of solvent extraction, fractional distillation, and so on. This paper reports on preliminary stages in the development of a method of treating these ores—particularly of niobium—so as to prepare the anhydrous, volatile halides by the use of chemical reagents which are much more easily handled than those used at present. CHEMICAL PRINCIPLES The solvent action of aminium halides has been referred to periodically in the literature over several decades. The chemistry of pyridinium chloride has been discussed particularly by Audreith2 and Starke.3 However, since this is not familiar chemistry in its nonaqueous setting, it is perhaps well to point out some general metallurgical principles and applications. One can use, as point of departure, the fact that HC1 dissolved in pyridine is an acid very much the same as aqueous HC1. It thus gives essentially all the reactions of the HC1 with which we are familiar. However, when the ratio of HC1:pyridine reaches 1:l (a ratio far higher than is possible with H2O) the solution becomes solid C5F5NHC1, pyridinium chloride.* Inter- estingly, the acidic properties of HC1 persist in this medium, although they are manifest only in the molten state of the compound. Some typical reactions of divalent metal compounds which we have carried out in our laboratories are the following: 2PyHCl + Zn — (ZnCl2) + H2 + 2Py 2PyHCl + MnO — (MnCl2) + H2O + 2Py 2PyHCl + CuS — (CuCl2) + H2S + 2Py 2PyHCl + CaCO3 — (CaCl2) + H2O + CO2 + 2Py In these equations, the parentheses indicate a solvated compound which in water would be predominantly a hydra ted cation but which in molten PyHCl will more likely be a complex chloro-anion of the type MC14-. Some important physical properties of pyridinium chloride (PyHCl) are given in Table I. One sees from the data in Table I that at the temperature of molten pyridinium chloride both water and pyridine will boil away. Thus the system will be kept anhydrous. For this reason the reaction 2NbCl5 + 5H2O— Nb2O5 + 10HC1 has no counterpart in molten PyHCl. Instead, the chloride is made even more stable by the formation of a hexachloro complex: Nb2O5 + 12PyHC1 — 2PyHNbC16 + 5H2O + 10Py One interesting property of these complexes is their thermal instability which for the case of niobium can be illustrated as PyHNbCl6 — PyHCl + NbCl5 With a view to possible use of this chemistry in ore treatment, we have attempted to dissolve Pyrochlore (essentially FeO - Nb2O5) and recover the NbC15 from it.

Jan 1, 1968

By S. Terry, W. Callender, R. J. Cornelius

When a dry ball-mill grinding circuit was in- stalled at the pellet plant of Hamersley Iron Pty. Ltd., it was something of a pioneering venture, since this was one of the first instances where such a circuit had been applied to iron ore on a major scale. The Hamersley pellet plant is located in Dampier on the coast of Western Australia. The feed for it consists of -8mm fines produced as a screened product at the Mt. Tom Price mine 186 miles inland from Dampier. It was these fines that encouraged the choice of a dry grinding facility for the plant. At the outset, tests had shown that the fines could not be filtered satisfactorily with a wet grinding system. At the pelletizing plant, the fines are stockpiled, reclaimed, dry ground in ball mills, formed into pellets on balling discs, hardened on an indurating line, and stockpiled for shipment overseas. These operations are shown in Fig. 1.

Jan 7, 1969

By Joseph Newton

MUCH the same story can be told about the copper industry for the year 1944 as for the three preceding years. Operators report few or no technical changes at their plants and the main endeavor has been to maintain high production with existing equipment. No large new installations have been made to increase plant capacities and apparently over-all copper production has passed its maximum. The present decline in copper production results partly from the severe labor shortage. As is true of most industries; the outstanding fact about the copper industry during the past few years has been its tremendous and sustained production which has been maintained in spite of serious shortages in material. labor, and technical personnel. The figures in Table I give a concrete example of how production has been increased at one large smelter in the United States-the Garfield plant of the American Smelting and Refining Co. at Garfield. Utah. These figures, reported by W. G. Rouillard. superintendent. give the production of the Garfield plant for the five years 1940-44 inclusive. The total blister production

Jan 1, 1945

By J. A. Hutcheson

NO one questions that it is technically possible to achieve the controlled release of atomic energy in a form that can be converted into heat or electricity. However, before this is actually an accomplished fact a great amount of work must .be done. This work falls into two general classifications: research and engineering development. At present a research program is under way in this country, co-ordinated and directed by the Atomic Energy Commission, which, as time goes on, will uncover fundamental knowledge of this new science that is essential before industrial applications of atomic energy are practical. Undoubtedly therefore, as the store of available knowledge increases, a time will come when answers to the many questions relating to practicality of atomic energy in industry can be determined with reasonable certainty. That the application of atomic energy in industry will eventually be proved practical is assumed. What then are the engineering problems that must be solved before the first practical electric power generating station can be built?

Jan 1, 1948

By Lovell Lawrence

MAGNETITE deposits in the Eastern States have been mined uninterruptedly since pre-Revolutionary War days. The industry, thriving in normal times, was given impetus in all periods of tumult, and continued to advance and expand, until the Lake Superior ores came into production. A period of comparative quiet existed until increased freight rates, together with increased mining costs on Lake Region ores, permitted the magnetites again to compete. This, coupled with World War demands, created unpre¬cedented activity. Producing plants were at their peak, new mines were equipped and put in operation and the industry pushed production beyond the absorption point. Ore stocks were tremendous, internal competition severe, and a great increase in import of European ores brought the industry to a low ebb in 1923.

Jan 1, 1933

By MERLE HOWARD GUISE

WHEN I was a boy I walked into Fairbanks in 1905. I was but a soft chechako, and arrived with blisters covering my feet, as a result of "mushing" the 400-mile trail on foot. Because of them, the display windows of the trading posts were first to catch my eye-dog and horse collars, harness and sled parts! And because of my enthusiasm for things adventurous, I looked long upon the prospectors' gold pans, shovels, rifles, camp equipment, and what not. Today those windows are filled with motor car accessories, tires and repair parts; yes, even thermos bottles and vacuum cleaners! There were many chance meetings with little parties of prospectors in my youth, and it always set my blood to tingling. Sometimes it was a 70-year-old sun-baked son of the Arizona desert, wrangling his stubborn, faithful jenny away from some outfitting store, at others a shovel-ended poling b0at in northern Canada, \vith the partners and the dogs towing upstream along the bank, or an old sourdough, with tug-rope around neck and hand on the spruce sapling gee-pole, mushing along behind his two or three old, plodding malamutes, dragging a little Yukon sled piled high with rusty sheet-iron stove, pick and shovel, cross-cut saw and axe, rifle, bales of dog salmon, and other paraphernalia. These meetings envisioned the panning of old creek beds and draws in the search for as yet undiscovered pay-channels; they meant the toughest kind of work sinking a hole to bedrock in some far-away valley of promise; they suggested wood fires to thaw the frozen muck and gravel and crude windlass and hand-made tub to hoist the water and the mud; but loudest of all they spoke of Adventure.

Jan 1, 1929

By Robert T. DeGavre

The $650 million financing for Into Ltd.'s Soroako nickel project is a story worth telling-not only because the project itself represents a significant achievement but also because there are certain important lessons that can be derived from our experience in financing the project. A critical appraisal of the methods and successes in the financing plan is presented in this article, in light of goals which Inco sought to achieve. A technical assessment of the project is not included, since Inco Ltd. has submitted a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of AIME in February 1979. Progress in developing and financing the project is encapsulated in the accompanying project factsheet.

Jan 3, 1979

By F. P. Haver, M. M. Wong

When a mixture of chalcopyrite concentrate and lime is heated in air, the following reaction takes place: 2CuFeS2 + 4Ca (OH)2 + 8 ½ 02 ; 2Cu0 + Fe203 + 4CaS04 + 4H20. Ca (OH)2 is the only common reagent that will adequately control SO2 evolution in roasting. Other additives tried, including CaO, CaCO3, Na2CO3, NaOH, MgO, Mg (OH)2, and MgCO3, were not effective. All reacted with sulfur, but not to the extent that will be required to meet the new control regulations for sulfur oxide emissions. For example: when the concentrate was heated with the theoretical amount of limestone (CaCO3), about 55% of the sulfur was retained in the calcine; whereas use of the stoichiometric amount of Ca (OH), converted approximately 99% of the sulfur to CaSO1. In most of the experiments, Ca(OH)2 was formed by adding CaO to concentrates containing enough water to simulate filter cake from flotation circuit. This eliminated the need for drying the concentrate and utilized the heat of hydration of CaO.

Jan 6, 1972

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By AIME AIME

THE CHAIRMAN of the fast growing Petroleum Division is not only a graduate of the University of California, but a third generation native son. After a few years spent in hard-rock geology, his professional efforts were transferred to the sedimentaries and to petroleum investigations, as a consulting geologist. For ten years these investigations covered the Rocky Mountain, Oklahoma, Texas, and eastern districts. After the war he returned to Casper, Wyo., as chief geologist for the Consolidated Royalty Oil and Western Exploration Companies. This employment afforded him the opportunity to study particularly the economic relationship between the lessor-lessee interests in development and production, a somewhat unusual type of petroleum specialization.

Jan 1, 1939