Search Documents

By W. J. Taylor

In making heating gas with anthracite coal for roasting ore during the past few years, I have tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has more of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 1 1/2 - inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer-is blown with

Jan 1, 1881

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103c1 Engineers, killed in action near Fismes, Aug. 9, 1918. Bowles, Martin F., 2d Lieut., Co. B, 355th Infantry, killed in action, Sept. 3, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on Oct. 7, 1915. Dougall, Ralph,. 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on Oct. 12, 1917. Gordy, Sheppard B., died in service, Oct. 9, 1918. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1, 1918.

Jan 1, 1919

By W. J. Taylor

IN making heating gas with anthracite coal for roasting ore during the past few years, I hare tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has pore of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 11/2-inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer. is blown with

Jan 1, 1881

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979

By Donald H. McLaughlin

ALTHOUGH Cerro de Pasco was well known since the early sixteen hundreds as one of the major silver districts of the Andes, its development on a modern scale did not occur until the first decade of the present century when a syndicate organized by James B. Haggin initiated the enterprise that eventually grew into the complex and widespread operations of the Cerro de Pasco Copper Corporation. Options on a few claims in Cerro de Pasco that had been brought to New York in 1900 came to the attention of A. W. McCune, a mining man from Salt Lake City, who took them to Haggin and soon succeeded in interesting that creative mining financier in the possibilities of the district. James MacFarlane, an engineer well known to both Haggin and McCune, was sent to Peru early in 1901 to make the initial examinations which promptly led to acquisition of a substantial group of claims in the heart of the mineralized area. A syndicate to which Haggin turned over his rights was organized on Feb. 26, 1902 to provide the necessary funds. The original members were J. B. Haggin, who retained a 34 per cent interest, Edward H. Clark (for Mrs. Phoebe Hearst, the widow of Haggin's old associate, George Hearst), H. McK. Twombly, H. C. Frick, D. O. Mills, and J.P. Morgan.

Jan 1, 1945

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the month of December, 1913: Members ADAMS, CHARLES W., JR., Smelting, American Smelting & Refining Co., Murray, Utah. ARMSTRONG, FRANK H., Mechanical Engineer Vulcan, Mich. ARNOLD, JOHN B., Attorney-at-Law Room 840,200 5th Ave., New York, N. Y. BOYS, HARRY R., Mining Paso Robles, Cal. CAVANAGH, JOHN L., Min. Engr., Nova Scotia Steel & Coal Co.; Wabana, Newfoundland. CHOW, KAI CHI, Student 1120 Amsterdam Ave., New York, N. Y. CLARK, ARTHUR B., Mining Engineer 72 Harbour Bldg., Butte, Mont. CURLEY, JOHN R., State Mine Inspector P. 0. Box 633, Leadville, Colo. DAVIS, ANGUS W., Mining Engineer, Consolidated Mining & Smelting Company of Canada, Trail, B. C., Canada.

Jan 1, 1914

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1914. Members ADAMS, DANIEL T., Mining 1416 Westminster Bldg., Chicago, Ill. BLICKENSDERFER, FRANK CLEVELAND, Sampler Morenci, Ariz. CAVERS, THOMAS WILLARD, Met Copperhill, Tenn. CLAPP, CHARLES H., Geol Univ. of Arizona, Tucson, Ariz. CLARK, PATRICK T., Pres Bullwhacker Mine, Spokane, Wash. COMSTOCK, HARRY, Mining Mineville, Essex Co., New York. COOKE, JOSEPH H., Gen. Mgr Mono Dev. Co., Gisborn, Tooele Co., Utah. COOPER, DEXTER P., Civ. and Hyd. Engr 101 Park Ave., New York, N. Y. DEGOLYER, E. L., Geol Apartado 269, Tampico, Mexico. DESHAYES, ERNEST F., Mine Foreman Baldy, N. M. DOUGLASS, WILLIAM CRAWFORD, Min. Engr 107 Leonard Hotel, Butte, Mont.

Jan 5, 1914

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1914: Members BAKER, FRED SHERMAN Tabowie, Unsan, Korea. BISSET, DANIEL GEORGE, Engr., 142 3d Ave., N. W., Edmonton So., Alberta, Canada.. BRANDT, MAURICE SHELDON, Chief Engr., White Eagle Mining & Milling Co., Box 298, Boulder, Colo. BROWNING, EDWARD, Min. Engr., Asst. to Supt., Cornwall Ore Bank Co., Cornwall, Pa. CASTLETON, WILLIAM ARTHUR, Mill Supt., East Butte Copper Mining Co., Butte, Mont. CHIDESTER, WALTER BARCLAY, Min. Engr., Care Mother Lode Mine, Greenwood, B. C., Canada. CLARK, EDWARD HARDY Mgr.,.Hearst Estate, 15 Broad St., New York, N. Y. CLARK, FREDERICK P., Chief Chem., International Lead Refining Co., East Chicago, Ind.

Jan 9, 1914

[Appalachian Petroleum Section: Walter H. Chapman, chairman; Jean Freeland, first vice-chairman; John Galpin, second vice-chairman; Jack L. Trittipo, secretary-treasurer. Meets 4th Tues., Humphreys Restaurant, Charleston. Balcones Section: William E. Richards, chairman; William C. Miller, Jr., first vice-chairman; Brantley G. Myers, second vice-chairman; Harold Vagtborg, Jr., secretary-treasurer. Meets 4th Wed., Petroleum Center Club, San Antonio. Big Horn Basin Subsection: Donald G. Davis, chairman; B. E. Yester, vice-chairman; J. F. Keleher, vice-chairman; Samuel N. Conley, third vice-chairman; William O. Snyder, secretary; M. J. England, treasurer. Billings Petroleum Section: N. J. Matthews, chairman; Guy J. Lookabaugh, first vice-chairman; George O. Ellis, second vice-chairman; Robert L. Spottswood, secretary-treasurer. Meets 3rd Tues., Turf Penthouse.]

Jan 1, 1961

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10' neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann's published data8 for solute redistribution for various Keff's and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By W. A. Tiller

The conventional techniques1 for determining the liquidus and solidus surfaces of an alloy system containing more than two components are extremely tedious to use and do not provide a complete picture of the equilibrium relations between solid and liquid alloys. These techniques are unable to yield "tie-line" information concerning solid and liquid phase equilibrium, a very important parameter in the solidification description of the liquid alloy and a very necessary parameter in the preparation of "zone-levelled" alloy crystals. The tie-line in a polycomponent system is analogous to the partition coefficient, k, in a binary system, it gives the composition of the solid, Cs, in equilibrium with a liquid of composition CL. That is, CS = kCL, where CL = [CO, c1,...Cn] denotes the concentrations of the n + 1 constituents, and k = [ko, kb ,...kon] denotes the gross partition coefficient for the elements between the two phases; thus, k is the tie-line in this system. To provide complete information concerning the two-phase equilibrium in a polycomponent system it is necessary to know both the liquidus surface and the gross partition coefficient. From these two the solidus surface is obtainable. The conventional techniques are unable to provide this information in other than a binary system so we must look elsewhere. In recent years considerable insight has been gained into the correct description of the liquid-solid transformation, 2,3 and controlled solidification experiments may now be designed to both facilitate and enhance equilibrium diagram studies. In the present paper consideration is given to two methods for obtaining the liquidus surface and the tie-lines in polycomponent systems. The methods to be described below deal with the solidification of an n + 1 constituent liquid alloy of initial composition [co, Co ,...Con], where the superscripts refer to the elements present and the Oth element is considered as the solvent in which the n solutes are dissolved. The general assumptions made in the treatment are the following: (i) the solid and the liquid at their interface are in equilibrium during the growth of the solid phase, (ii) there is no diffusion in the solid phase, and (iii) the liquid phase is completely mixed and is therefore homogeneous in concentration. METHOD I In this section a general experimental method will be described which, in principle, is capable of giving an exact description of the liquidus surface and tie-lines. Consider the unidirectional solidification of the liquid alloy specimens L cm in length (freezing either horizontally or vertically). Allow the sample to be frozen very slowly from one end, as indicated in Fig. 1, with complete mixing in the liquid, and then analyze the solid bar to determine its chemical constitution as a function of position, x, along the bar. Let Fig. 2 represent a possible distribution of the ith constituent along the bar. At the point x' the concentration of the ith constituent is C1/5(x'), and the average concentration of the rest of the bar between x' and L is given by C:(X' - L) where [ A(x) c1s(x)dx c1/s(x'-L) = f A(x) dx x * and A(X) is the cross-sectional area at x. In a similar manner. all the Cf(x' - L) may be determined. Thus, the gross artition coefficient k for liquid of composition [Cs(x - L),...Cs(X' - L)] is given by -ko= CUs')/Cos(x' - L)" k0 = csn{x')/cs(x'- L) During the freezing of a charge of length L, the liquid composition may vary over a wide segment of the phase diagram and the gross partition coefficient over this segment of the phase diagram may be determined from one, bar. Fig. 3 illustrates the magnitude of Cs(g)/C,' as a function of the fraction g of the bar which has Solidified.2 We can see that the concentration in the bar will vary over a range of about 15 wt pct for C,' = 10 wt pct and k0 = 0.5. It appears that 4 or 5 specimens would be adequate to study a simple binary eutectic phase diagram.

Jan 1, 1960

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Larry Dale

An approach for predicting the development of mineral resources on public lands has been developed as an aid to resource agencies. It consists of new techniques for evaluating the economic potential of the resource, the uncertainty about mine cost estimates, and the uncertainty about the occurrance of mineral deposits. New mineral sup- plies from inferred and hypothetical resources can be predicted by using these techniques. A case study illustrates their application in predicting development of copper resources in western Montana.

Jan 1, 1982

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By G. P. Conard, R. C. Hall, J. F. Libsch

The 50 pct Fe-50 pct Co alloy undergoes a transformation from disorder to an ordered structure of the CsCl type reportedly in the vicinity of 732OC. During this process, the coercive force goes through a maximum, apparently as a result of strains associated with the coherent nucleation and growth reaction. This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction, which is associated with annealing to a high degree of order with the continuous application of a magnetic field. The increase in ratio can be explained on the basis of a decrease in 90' domain boundaries and, perhaps, by an increase in anisotropy resulting from lattice distortion. THE 50 pct Fe-50 pct Co alloy undergoes a disorder-order transformation which has been reported to occur in the vicinity of 732°C1,2 The ordered structure is the CsCl type.' This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction as a result of heat treatment in a magnetic field, sometimes called a response to magnetic anneal.'-' The purpose of this investigation was to study the course of the ordering reaction, the nature of the response to .heat treatment in a magnetic field, and the relation, if any, between ordering and the response. Procedure The method of approach in this investigation was to produce an initial structure as completely disordered as possible and then gradually to order the alloy by isothermal anneals at various temperatures under different conditions of the applied magnetic field. Magnetic, magnetostriction, and X-ray analyses were of primary importance in determining the property and structural changes resulting from the isothermal anneals. Rings of the 50 pct Fe-50 pct Co alloy were prepared from the elemental powders by a powder metallurgy technique, further details of which may be found in ref. 7. The initial structure was produced by annealing the specimens for ½ hr at 1000°C, cooling to and holding for ½ hr at 900°C (in the a range above the ordering temperature), and water quenching. Isothermal anneals were performed at 600°, 675°, 720°, and 740°C. For example, rings were heated to 600°C, held for a predetermined period of time, and cooled by natural cooling at a rate slightly slower than an air cool (average of 20" to 25°C per min). The tests (magnetic, etc.) were made after each heat treatment. All high temperature treatments were performed in a purified hydrogen atmosphere. The treatments at the various temperatures were carried out under one or more conditions of an applied field including 1—no field, 2—field of 20 oersteds applied on cooling only, and 3—field of 20 oersteds applied continuously during heating, holding, and cooling. Magnetic measurements were made using the standard Rowland ring technique8 with a maximum field strength of 100 oersteds. The magnetization curve, induction at 100 oersteds (B.), residual induction (Bt), and coercive force (Hc) were determined. All magnetic analysis data were based on an average of the results from three rings. A strain gage technique9 as used for the measurement of magnetostriction. The X-ray determination of the relative amount of ordered phase present was made on the ring specimen used for magnetic measurement. This was done by the back-reflection method using a rotating specimen (because of the large grain size) with unfiltered CoKa radiation and a 7 hr exposure time. Intensity measurements of the ordered line (300) were made by comparing visually the films so obtained with standard films prepared by exposing for different lengths of time a specimen given a long time anneal (high degree of order). Results In all instances the saturation induction (induction at 100 oersteds) was found to increase slightly with annealing time. This effect was small and appears to be the increase in saturation induction to be expected on ordering.10-13 The residual induction behavior was markedly influenced by the field condition during annealing, Figs. 1, 2. For the condition of no applied field, the ratio of residual to saturation induction remained essentially constant for short annealing times but showed a significant increase at longer times. With increasing annealing temperature, less time was required to produce this increase in the ratio. In the case of the 600°C anneals, the increase did not occur until approximately 20 hr, Fig. I, while on annealing at 740°C the increase was immediate, Fig. 2. Slight decreases in the ratio may be observed at 100 hr for specimens treated at 720°C and at 1 hr for those treated at 740°C. Specimens annealed in a field of 20 oersteds showed a residual to saturation induction ratio consistently higher than that for the specimens annealed without the field. The first anneal with the field (¼ hr) caused an abrupt increase in the ratio at all temperatures; thereafter, the increase in the ratio was generally similar for specimens annealed

Jan 1, 1956

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950