Search Documents

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By C. Michael Morgano

Static tests are costly and time consuming, so they are not always the best answer [ ]

Jan 1, 2005

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is an extensively utilized geotechnical tool for site characterization. DST provides low strain (<10-5) in-situ interval shear and compression wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. The DST arrival times have associated measurements errors and resolution limitations, which become more pronounced as the depth interval of analysis is reduced. Baziw Consulting Engineers (BCE) has developed a new DST analysis technique, the so-called DSTPolyKF algorithm, whereby the arrival times of DST data set are used to define a high order polynomial. The main advantages of this new technique are four-fold: 1) the ability to utilize all arrival time estimates irrespective of measurement errors. 2) the ability to analyze the data with user specified and even small (≤ 0.5m) depth intervals. 3) the ability to apply sophisticated data fusion for significantly more accurate DST interval velocity estimation. 4) the use of polynomial regression accuracy parameters to quantify how well the “best fit” polynomial fits the acquired arrival time data sets. This paper outlines the mathematical details of the best fit polynomial where a Kalman filter formulation is implemented. The performance of the DSTPolyKF algorithm is demonstrated by processing real DST data sets.

Oct 1, 2022

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By Jason N. Scott

It is now possible using low-cost wireless technology and rugged hand-held devices to record data on site electronically and for that data to be instantly available to others. This could potentially eliminate many problems that traditionally lead to remedial work, such as poor communication and the late detection of non­conformances. However, determining how best to implement such a system and integrate it with the rest of the business process is far from simple. This paper looks at Stent&apos;s experience of these issues by way of a case study of the SHERPA system. This is a wireless site data collection system developed for use with rotary bored piling.

Jan 1, 2006

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta&apos;s harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By H. R. Taber

The extensive subject area "Engineering Practice of Ground Improvement" will be treated within the limitations of space and the writer on the basis of personal practice and experience?largely in Northern California over a period of some thirty-six years and, in "ground improvement" work, with an emphasis on transportation facilities. The stress is on improvement of ground conditions, rather than on techniques of improving inherent earth materials characteristics. "Ground improvement" is discussed as engineering resolution of existing or emergent earth materials defects or deficiencies?that is, as the technically feasible procedures best adapted to achieving a required level of service within physical, economic, social and other constraints. A "required level of service" concept is presented as a tool in evaluation of appropriate ground improvement work.

Jan 1, 2010

By Walter Ensinger

Working safely means working cost-effectively. Every "dangerous occurrence" and - even more so - every industrial accident causes disruptions in the planned course of construction. Besides moral and legal obligations, economic aspects are therefore also factors motivating increased efforts towards optimal prevention: improvements in work safety and protection of health are wise investments! Ever since its earliest days, the European Federation of Foundation Contractors (EFFC) has made this subject one of its key objectives and therefore set up a Safety + Environmental Working Group, in which experts from the member organisations exchange national experience and develop proposals for "best practices". The paper presents current developments and results from the work of the S+E WG with particular reference to the project "Ideas for Safety Improvement".

Jan 1, 2006

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades&apos; experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By Venkatesh S. V J, Shubha M, Srilakshmi G

Choosing for the best option of pile foundations to overcome large lateral and uplift loads for the foundations in transmission line towers/offshore environment is still being a concern to achieve the required capacities but also by considering the suitability aspect in the environment. The objective of this paper is to review the methods that have been done for knowing the uplift resistance and lateral resistance of pedestal piles. Investigations by different methods such as experimental studies, numerical and analytical studies have been done by various researchers in order to evaluate the response of a belled pile. These methods are discussed in this paper and the comparison with straight shaft pile based upon the test and analysis. The results indicated that the uplift resistance and lateral resistance were significantly increased with the adoption of belled piles than straight shaft piles.

Sep 1, 2022

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006