Search Documents

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By George Saratsis, George Exadaktylos

In the marbel industry, ore reserves refer to the produced tonnage of orthogonal prismatic, defect-free blocks of commercial sizes and of marketable aesthetical quality. On the contrary, in the mining sector, ore reserves refer to the tonnage of ore with grade above some cut-off value. While in the mining sector ore reserves are reported according to existing standard guidelines, the marble industry has no standardmethod. The purpose of this paper is to present a method to estimate white marble reserves using drill coring or borehole wall logging and limited joint mapping on exposed marble surfaces. Data pertaining to fracture orientation, fracture frequency, size, and whiteness were collected. The primary phase of marble characterization is followed by the discretization of the orebody into a three-dimensional array of orthogonal prismatic blocks, where the marble whiteness and fracture intensity are attribute values. Both these variables are considered to obey continuous and not discrete probability distributions. The discretization is performed using computer aided design and the Block Kriging techniques. An outline to improve the description of a given marble ore deposit at the exploration stage is presented for the prediction of marble block size distribution from joint count measurements along diamond drill cores. An example case of a white dolomitic marble quarry is used to demonstrate these methods.

May 27, 2020

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Two other minerals, cryolite and fluorapatite, have significant fluorine content. Cryolite, sodium aluminum fluoride, Na3AlF,, is a rare mineral that has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. Fluorapatite, Ca5F(PO3)2, is a source of phosphate for fertilizer manufacture, containing a small percentage of fluorine. Commercially mined deposits of apatite have varying amounts of fluorine, chlorine, hydroxyl, and carbonate. HISTORY Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in 16th century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and 11. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s and the application of heavy media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological advances that facilitated increased production. Pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. USES OF FLUORITE Fluorspar is used to make hydrogen fluoride (HF), also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride is produced by reacting acid grade (97% CaF,) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation; the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, an ingredient in high-octane fuel for aircraft and automobiles; in steel pickling, enamel stripping, and glass etching and polishing; and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 12 to 29 kg of fluorine content in synthetic cryolite and aluminum fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly in countries with the most advanced technology (i.e., Australia and Sweden), while others (i.e., Surinam and South Africa), remain at the high end. Elemental fluorine is prepared from anhydrous hydrofluoric acid by electrolysis. Gaseous at room temperature and pressure, fluorine is compressed to a liquid for shipment in cylinders or in tank trucks. Elemental fluorine is used to make uranium hexafluoride, sulfur hexafluoride, and halogen fluorides. Gaseous uranium hexafluoride is used in separating U235 from U233 by the diffusion process. Sulfur hexafluoride is a stable high dielectric gas used in coaxial cables, transformers, and radar wave guides. Halogen fluorides have important applications, mostly as substitutes for elemental fluorine, which is more difficult to handle. Emulsified perfluorochemicals, organic compounds in which all hydrogen atoms have been replaced by fluorine, are undergoing investigation as promising blood substitutes. They transport oxygen and, in conjunction with a simulated blood serum, perform many functions of whole blood. With further development, these organic compounds may ultimately, in emergencies, be useful in saving lives of animals and humans during periods of acute shortages of natural blood. Inorganic fluorides are used as insecticides, preservatives, antiseptics, ceramic additives, and fluxes and in electroplating solutions, antioxidants, and many other products. Boron trifluoride is an important catalyst. Organic fluorides are volume leaders in the fluorine chemical industry. Fluorinated chlorocarbons and fluorocarbons are prepared by the interaction of anhydrous HF with chloroform, perchlorethylene and carbon tetrachloride, and are characterized by low toxicity and notable chemical stability. They perform outstandingly as refrigerants, aerosol propellants, solvents, and cleaning agents and as intermediates for polymers such as fluorocarbon resins and elastomers. Fluorocarbon resins are inert compounds that have unusually low coefficients of friction and have found a number of applications as lubricants for parts that cannot be oiled, e.g., bearings for window raising equipment located inside of automobile doors, in small electronic equipment, for the manufacture of chem-

Jan 1, 1994

By Edie Trimmer

Utah statute defines sovereign lands as "those lands lying below the ordinary high water mark of navigable bodies of water at the date of statehood, and owned by the state by virtue of its sovereignty." The lands within the bed of Great Salt Lake (GSL) are, by this definition, sovereign lands, acquired at statehood in 1896 in accordance with the "equal footing" doctrine, granting each state control and ownership of navigable waters and the lands underneath those waters within its borders. Under public trust doctrine, the state, as trustee for the people, bears responsibility for preserving and protecting the right of the public to use of the waters for navigation, commerce, fishing, recreation, and wildlife habitat. Also by statute, sovereign lands are defined as "state lands," to be managed by "multiple use sustained-yield principles." The Division of Forestry, Fire and State Lands is given management authority for sovereign lands and, as manager, has responsibility to prepare comprehensive plans, initiate studies of the lake and its resources, implement comprehensive plans through state and local entities, and coordinate the activities of various divisions within the Department of Natural Resources (DNR). The Division of Forestry, Fire and State Lands also has responsibility for management of mineral leasing on sovereign lands. The many resources on the lake--water, minerals, wildlife, recreation, archeological and historical values--are managed by as many state agencies which occasionally creates conflicts. The brines of GSL contain several ions that crystalize into valuable minerals during evaporation. The major ions in the lake are, in order of relative abundance, chloride, sodium, sulfate, magnesium, and potassium. Mineral products which are currently extracted from lake brines are sodium chloride, magnesium chloride brine which can be sold as flake magnesium chloride or further processed into magnesium and chlorine gas, and potassium sulfate. Mineral products which have potential for extraction include gypsum, sodium sulfate, and trace amounts of lithium, boron, and bromine. The GSL contained an estimated 4.3 billion short tons (st) (3.9 billion metric tons [mt]) of dissolved salts in 1998. Utah Geological Survey (UGS) estimates of the dissolved salt content in GSL have fluctuated from 4.0 to 5.5 billion st (3.6 to 5.0 billion mt) due to the dynamic conditions in the lake as salts are precipitated and redissolved, and due to the diversion of brines from GSL, such as the West Desert Pumping Project. The lake has four areas of varying salinity, separated by dikes or other man-made structures: north arm and Stansbury Bay brines at near saturation (25 to 27 percent total dissolved solids [TDS]); the main body of the south arm with concentrations ranging from 7 to 15 percent TDS as lake elevations fluctuate; the waters in Farmington Bay at approximately 3 to 5 percent TDS; and Bear River Bay at <1 to 7 percent TDS. The percent TDS in Bear River Bay fluctuates with lake level, and changes in Bear River inflow. The transfer of salts from the south arm to the north arm has raised questions about the viability of the mineral and brine shrimp industries. The UGS and the U.S. Geological Survey (USGS) continue to monitor salinities at designated sites on the lake to document changing lake salinity. A recurrent theme is that placement of dikes and diversions can have significant and rapid impacts on various conditions in the lake. Hydrocarbon resources on the lake are significant, but presently undeveloped. The hydrocarbons are low gravity (4 to 9 degree API) and tar-like, contain high nitrogen concentrations, and up to 12 percent sulfur. The unusual characteristics of the oil have been the subject of studies by chemists at Weber State University and University Louis Pasteur de Strasbourg. However, these resources are difficult, and at present, uneconomic to extract using current technology because of the nature of the hydrocarbons, and production in "an offshore, highly saline environment." Oolitic sand deposits make up many of the beaches and shorelines around the lake. Because of their high calcium carbonate content, oolites have been used by Magnesium Corporation of America (MagCorp) and its predecessors for acid neutralization and dike construction. Oolites are also used in very minor amounts in flower drying. The Utah Division of Oil, Gas and Mining reports up to 130,000 st (118,000 mt) mined annually by MagCorp from U.S. Bureau of Land Management (BLM) lands adjacent to GSL. Currently, there are twelve producing mineral leases which generated slightly more than $1,000,000 in royalties during calendar year 1998. IMC Kalium Ogden Corp. (IMC Kalium) produces potassium sulfate and magnesium chloride from brines concentrated through solar evaporation in Bear River Bay and Clyman Bay. By-product sodium chloride is transferred to IMC Salt, which packages and sells the salt. MagCorp produces magnesium metal from brines concentrated in Stansbury Bay. Cargill Salt produces sodium chloride from brines provided by MagCorp under a lease agreement. Morton Salt produces salt at the southeast end of Stansbury Island. Lastly, North Shore Limited produces cocentrated brines for use in dietary and mineral/vitamin supplements near Spring Bay in the north arm of the lake. Producers of magnesium, potash, and salt from GSL contribute significantly to the value of metals and industrial minerals in Utah. Together these companies contribute approximately $240 million in gross value, or 18 percent of the value of the state&apos;s nonfuel mineral production. Most of this production is exported.

Jan 1, 2001

By A. L. Frank, Benton

INTRODUCTION The selective sensitivity of plastic nuclear track detectors (PNTD&apos;s) to low energy 4He particles in an environment which also contains gamma and beta radiations has made these detectors prime candidates for the dosimetric measurement of the concentrations of radon and its daughter products in mine air. Their passive, integrating mode of measurement, small size, low weight and inexpensiveness are attractive characteristics for large scale personnel dosimetry. The detectors can be used in either active or passive dosimeters. In active devices, the PNTD is placed in close proximity to a sampling filter. The filter collects, from a calibrated air flow, all the daughter nuclei which are in suspension. As the daughter nuclei pass through the decay chain, through 214Po, a fraction of the 4He particles emitted are registered as latent tracks in the plastic. In passive devices, the PNTD is placed in direct contact with the ambient air containing the radio-nuclei concentrations to be determined. The active dosimeters have the advantage of excellent sensitivity, and the measured track densities yield very close approximations to accumulated Working Level (WL)** exposures. They have the disadvantage that the simplicity of the passive PNTD is lost, since a battery-driven constant flow-rate air pump is a necessity. The passive dosimeters are simple in construction and use, but they have the disadvantage that WL exposures are not directly measured and certain assumptions concerning radon and daughter equilibrium conditions must be made in determining WL exposures from the measured track densities. Also the sensitivities, in track densities per Working Level Hour (WLH) exposure, are much less than for active dosimeters. Dosimeters of both types have been investigated. Passive devices have been tested extensively both in the laboratory and in mines. Active devices have been laboratory tested. In our earlier measurements, cellulose nitrate plastic detectors were used exclusively, since this material had the highest sensitivity of the PNTD&apos;s then in use. When the properties of CR-39 plastic were discovered (Cartwright, 1978; Cassou and Benton, 1978), this material was used, where possible, to take advantage of its superior sensitivity. The results of our earlier work have previously been published (Frank and Benton, 1977). * Research sponsored by the Bureau of Mines, U.S. Department of Interior, under Contract No. JO-188003. ** A Working Level is defined as any combination of the short-lived radon daughters containing 1.3 x 105 MeV of potential 4He-particle energy per liter of ambient air. PASSIVE DOSIMETRY In the earliest testing of PNTD&apos;s for passive WL dosimetry, a single strip of cellulose nitrate plastic was used to determine the total cumulative 4He-particle activity in the air of simulated uranium mine and uranium mine environments (Rock, 1968; Rock [et al], 1969; White, 1969). The measurements yielded a close relationship between track densities and WL exposures in a controlled, static environment, but poor accuracy in the active mine tests. It was assumed that equilibrium differences contributed largely to the variations found. The response of PNTD&apos;s to airborne 4He-particle emitters, derived by Lovett (1969), demonstrated that detectors such as cellulose nitrate, which has a sensitivity cutoff at 4He-particle energies below the emission energies of radon and its daughters, are equally sensitive to the activity concentrations of radon, 218po(RaA) and 214Po(RaC&apos;). Since radon does not contribute to WL as it is defined, and since, under normal ventilated uranium mine conditions, the radon activity constitutes about 40% to 70% of the total 4He-particle activity, the WL exposures calculated from measured track densities are very sensitive to the particular radon daughter equilibrium conditions. Also, the detector does not weight the individual daughter activities in proportion to their importance to WL. The equation for WL is WL = 0.00103C2 + 0.00507C3 + 0.00373C4 (1) where C2, C3 and C4 are the activity concentrations of RaA, RaB and RaC-C&apos;, respectively, in pCi/[L]. The detector leaves C3 unmeasured and weights C2 and C4, equally. [This problem has been approached by Domanski et al (1975, 1979), for some non-uranium mines, by measuring equilibrium conditions throughout the mines to determine a mean value for A, the inverse of the Working Level Ratio (WLR = 100 WL where C1 is the activity of radon-222 in pCi/[L].) The distribution of values allowed Domanski to determine probable errors in calculating WL exposures from track densities. However, measurements of equilibrium conditions in U.S. uranium mines (Breslin et al, 1969; Holub and Droullard, 1978) indicate that this method would not be accurate enough for uranium miner personal dosimetry.] A two-element dosimeter was designed at our laboratory to compensate for equilibrium variations. The first element is a radon detector; the second is a detector for the total 4He-particle activity in the ambient air, just as in the single element dosimeters cited above. The addition of the radon detector allows the equilibrium conditions for the individual nuclei to be determined, given certain assumptions concerning the interrelationships between the nuclei concentrations in mine air. The two detectors and the problems involved in calculating WL exposures from their measurements are discussed below.

Jan 1, 1981

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By Richard B. Berg

California was a major talc-producing State until the late 1980s when production from the deposits in the Death Valley area ceased because of a number of factors which included pressure to discontinue mining in and around Death Valley National Monument, and health concerns affecting markets for tremolitic talc. The states of Montana and Texas now account for slightly more than half of U.S. talc production. Deposits in an area encompassing southern Death Valley and extending east into the Kingston Range were formed by contact metamorphism of carbonate beds in the Precambrian Crystal Spring Formation next to Precambrian diabase sills. These deposits contain ore ranging from high-purity, fine-grained talc to platy, tremolitic talc with high brightness. Deposits of tremolitic talc and talc schist in the Silver Lake District in San Bernardino County resulted from metamorphism of Precambrian carbonate beds intruded by granitic plutons. Northeast in Esmeralda County, Nevada hydrothermal alteration related to Late Jurassic plutons caused talc replacement of Precambrian to Early Cambrian dolomite. A hydrothermal origin is also indicated for talc deposits in the lnyo Range just north of the Death Valley District where bodies of unusually pure talc occur in Paleozoic lime- stone near Jurassic granitic plutons. Talc is now mined from a deposit in the foothills of the Sierra Nevada Range southeast of Sacramento where quartz-mica schist of the Permian Calaveras Formation has been hydrothermally altered to talc. Replacement of magnesite of the Precambrian Allamoore Formation produced talc deposits mined in the Allamoore District of west Texas. This dark-gray talc of low iron content with carbon- aceous material and dolomite is ideally suited for use in ceramics where it makes a white product when fired. Small bodies of platy light-pink to white talc suitable for use as an extender in paint are also mined in this district. In the Llano District of central Texas talc has replaced impure carbonate rocks and serpentinite. All Montana talc production is from deposits in the southwestern part of the State that formed by Precambrian hydrothermal alteration of dolomitic marble. This alteration produced material with high purity that ranges from very fine-grained, massive talc to coarser grained, foliated talc. Markets include pitch control in paper, paint, cosmetics, ceramics, rubber and plastics. In southwestern and northeastern Oregon, talc has replaced serpentinite in the vicinity of Mesozoic plutons. Soapstone for carving is mined from a southwestern Oregon deposit. Deposits of similar origin occur in central and northwestern Washington.

Jan 1, 1995

By Mritunjoy Sengupta

The Green River formations in the Western U.S.A. contains vast amounts of petroleum reserves in oil shale deposits. Exploitation of this petroleum reserve calls for large scale mining of the oil shale. Applicable mining methods include conventional underground mining using roan and pillar, sub-level caving and block caving; underground insitu retorting of oil shale and open pit mining. Roam and pillar mining offers one of the most economic methods of underground mining of oil shale. A 2.4 x l09 litre per year (50,000 barrels per day) of crude oil production would require a daily oil shale production of 100,000 tomes per day from underground operations. For this large production, a highly mechanized room and pillar mining muld utilize large capacity diesel equipment such as 85 tonne trucks and 8m front end loaders. The total air requirements of an oil shale mining operations can. be as high as 28443/s. Ventilation planning for such a large scale underground mining operation presents a formidable task. The major objectives of providing ventilation air to underground workings are to dilute airborne .dust and diesel fumes to harmless levels, and to insure that the mine environment is compatible with the health and safety of mine personnel. Regulation of air velocities and air temperatures is a major factor in mine environmental control. Colorado State law requires that a minimum of 0.047m3/s of fresh air be supplied for each kW of diesel power operating underground. Additionally, 0.047m3/s of fresh air must be supplied for each underground employee, and a minimum air velocity of 0.15m/s must be maintained in all working places. It is desirable to exceed this minimum velocity in order to prevent stratification of ventilation air. Moreover, Colorado law also stipulates the maximum allowable concentration of noxious gases mine air, below: ? C02 - 0.5% by volume, 5,000 ppm. ? CO - 0.005% by volume, 50 ppm. ? Oxides of Nitrogen - 0.0025% by volume, 25ppm. ? Nitrogen Dioxide 0.005% by volume, 5 ppm. This paper examines ventilation requirements for the underground mine, with respect to air quality requirements and distribution of air in mine workings in light of the above regulations. Analyses were made for sane typical mining plans to determine airflow resistance or pressure drops and fan horsepower requirements. In addition, the possible occurrence of high concentrations of toxic gases, was examined. Expected temperature levels in mine workings were approximated.

Jan 1, 1980

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies&apos; pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm&apos;s financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment&apos;s optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world&apos;s supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today&apos;s mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida&apos;s phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By Manfred G. Raschke

INTRODUCTION In the past decade, the international coal trade has been undergoing a period of gradual change. This change will continue through the remainder of this century until by the year 2000 the international coal industry will look very different from the industry which existed in the early 1970&apos;s. The industry which will emerge from the thirty year period of change (1970-2000) will be different in many ways. -The volumes of coal transported will be much larger. - The primary type of coal traded will be steam coal rather than metallurgical coal. - A much broader group of countries will be participating in the trade both as suppliers and as consumers. - The trade will be dominated by a relatively small number of large producing and trading companies. - The coal mined for international shipment will be primarily surface- mined. – The United States will play a decreasingly important role in international coal trade. In the course of this paper I propose to address three questions which are crucial to the formulation of an understanding of the changes outlined above : (1) Which supplier nations will be most successful in the international metallurgical and steam coal trade in the next decade and a half? (2) What emerging trends will shape the international coal trade in the 1980&apos;s and 19901s? (3) Where are U.S. producers likely to fit in this scheme of things? As a background to my remarks, I should note that what follows is based on five years of work in a consulting capacity on coal supply and demand issues worldwide. Although in the course of this work I have had occasion to develop mining and transportation cost figures for all of the countries discussed below--both my own and those obtained from coal producers--it is apparent that success in the marketplace can be determined in some instances by considerations other than costs. Nevertheless, my comments today about international competitiveness will be dominated by cost considerations; there are, after all, not many markets that reward the high-cost producer with success. Let us begin by establishing some criteria for success in the international coal market and then compare some of the producer nations to some of these criteria. The criteria are: - Low delivered cost, - Good quality coal, - The producer&apos;s partnership in a joint mining venture with an importer or a consumer of coal, - The producer&apos;s international business orientation and commitment to penetrating the market, - The producer&apos;s reliability as a supplier, and - Political pressure exerted by the producing country on consumers.

Jan 1, 1986

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Peter Zhang, Daniel Su, Heather Dougherty, Jack Trackemas

"Longwall mining has a significant influence on gas wells located within longwall chain pillars. Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings. If the gas well casings are compromised or ruptured, natural gas could migrate into the mine workings, potentially causing a fire or explosion. By the current safety regulations, the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars. The current regulations for the gas well pillar design are based on the 1957 Pennsylvania gas well pillar study. The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars. As the guidelines were developed for room-and-pillar mining under shallow cover, they are no longer applicable to modern longwall mining, particularly under deep cover. Gas well casing failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh coal seam. The study indicates that overburden depth and pillar size are not the only determining factors for gas well stability. The other important factors also include subsurface ground movement, overburden geology, and weak floor, as well as the construction of gas wells. Numerical modeling was used to model abutment pressure, subsurface deformations, and the response of gas well casings. The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above, within, and below the chain pillars, and the potential location and modes of gas well failures, therefore providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.INTRODUCTIONIn the eastern United States, abundant gas wells have been drilled through coal seams that are being actively mined by longwall mining. The existence of gas wells in the U.S. coal fields, whether active or abandoned, have caused many issues for longwall mining. First of all, any gas well in the mining area has to be located by all possible means. Secondly, the gas wells within longwall panels have to be plugged, as cutting through gas wells will allow natural gas to flow into the active longwall mines. On the other hand, the gas wells within longwall chain pillars or barrier pillars can be left in place if the wells are protected by properly designed pillars."

Jan 1, 2019

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation&apos;s remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society&apos;s control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980