Search Documents

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By W. A. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on their mine plans. Incorporating changes such as commodity prices, customer sales, fluctuating cost assumptions and newly acquired geologic data requires quick turnaround for model building and planning to keep mine plans on pace with changes as they occur. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. To meet these challenges, one leading North American mining company successfully increased the frequency rate and accuracy of its mine plans to stay current with incoming data, ensuring its mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By G. B. McClurg

China was nota factor in the supply of fluorspar to the United States until the early 1980's when it shipped in its first package of Metallurgical lump, that not only was higher grade than the Mexican Metallurgical spar but was also about $30.00 a ton cheaper landed at Burnside. Representatives of the Mexican Fluorspar Institute and several producers made trips to see the Chinese operations supplying their once reserved market place. China, an enigma to most Westerners suddenly became the new contender, with prices that were disgustingly low or so thought the other exporters. Of course China has been mining, producing, consuming and exporting from 400,000 to 500,000 tons per year of various grades of fluorspar but until the first partloads came to the U.S., very little attention was paid to their exports by American-continent producers or consumers.

Jan 1, 1986

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By T. J. Loyd

The capabilities of the analog computer, the Mine Ventilation Simulator, installed at WHA's Safety and Health Technology Center in Denver, Colorado, are discussed. General opera- ting procedures are described showing how a mine model is produced, and how the model can subsequently be modified to produce a solution to a mine ventilation problem. A sample problem is included to illustrate the technique. The important role the Mine Ventilation Simulator plays in ventilation training is discussed, including experiences with the education of students at the Colorado School of Mines. This paper includes a summary of some of the advantages and disadvantages of the analog technique and suggests some design criteria for application to future development of analog computers, based on experience gained with the Mine Ventilation Simulator.

Jan 1, 1984

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo, Noelia Munoz-Garcia, Michèle Heitz

Sulfide tailings from past and present mining activities are important hosts of critical elements and precious metals. This review paper presented a literature survey on the recovery practices of some critical minerals containing Te from sulfide tailings with a special focus on the physical beneficiation and hydrometallurgical separation methods. Finally, a conceptual framework and possible processing flowsheets were proposed. The findings of this review will be useful for the researchers in the field of geochemistry, mineral processing, and metallurgy to evaluate the separation processes for reprocessing of mine tailings for the recovery of critical minerals.

Feb 1, 2024

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By Juan L. Yarmuch, Gonzalo Sepulveda

This article presents a novel approach to address the mining width-constrained open pit mine production scheduling problem in the context of medium-term planning. A mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the NPV of the schedule while ensuring enough room for the operation of mining equipment. To tackle the computational challenges posed by large-scale instances of the problem, we propose a method based on variable fixing and horizontal precedence generation. In this study, we apply the developed model to real-world scenarios from Radomiro Tomic short-term mine planning problems such as optimizing the timing of major truck maintenance and the impact of external factors, like the delay in the production of the Chuquicamata underground project. Remarkable improvements are observed with the mining width-constrained model. Specifically, the mining width satisfiability is enhanced from 2 to 60% compared to the traditional open pit mine production scheduling model, underscoring the significance of incorporating these constraints. The proposed method showed good results reaching optimality gaps within 5%.

Mar 28, 2024

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By Ari Glazer

"Every year the tunneling business is expanding and collaboration with the International Society of City and Regional Planners (ISOCARP) for the future design of cities and urban communities is in the making. During the last half of this century, billions of people migrated to cities, and it is estimated that by 2030 almost five billion people worldwide will reside in urban communities. Hence, “Underground development will be an important tool in reshaping our urban areas to meet the challenges of the future without destroying their heritage or worsening their surface environment” (Esaki, 2005). In 2013, the Organization for Economic Co-operation and Development (OECD) estimated life expectancy to be around 80 years, meaning that in less than a decade we will need to bury billions of people in cities and urban communities, while trying to retain the deceased’s beliefs and customs. Religion plays a major role in our lives, and many people worldwide still decline to cremate their body after their death; therefore, cemeteries are essential for city inhabitants. Rites and traditions usually call for burials to be near the place of residence, which allows the remaining family members and friends to visit the grave frequently, at least in the first years. This is a challenge that urban designers and architects must confront while trying to solve the problems of future urbanization. In recent years, population growth, the rising cost of land and the extensive preservation of green areas have made cemeteries a burden and a nuisance, particularly for large cities and communities. Many graveyards that were once on the city's outskirts have become lifeless islands in populated areas (Fig. 1), rarely visited by the second and later generations. Cities worldwide face the challenge of allocating less land to maintain current burial practices. In response, some cities have begun to bury their dead at a great distance from the community; others have started to stacked burials, one on top of the other, while still others are constructing buildings and even skyscrapers for the practice of burial (Fig. 2)."

Jan 1, 2016

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024