Search Documents

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By James Wm. White

Today a large number of open pit mines use computer-based mine management systems to automatically assign haul trucks, track equipment, and manage information. Now advances in digital communications allow the use of these systems in underground operations. Underground mine management systems help maximize production by providing impressive gains in areas such as equipment and manpower utilization, draw point equalization in block caving operations, preventive maintenance, and safety. Current systems use allocated or "locked" train and LHD dispatching. While allocated dis-patching rarely optimizes open pit production, it offers an efficient mode of operation underground where options are more limited.

Jan 1, 1996

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By Thomas A. Palmer

Free cyanide has been successfully determined in ground and surface water by isolation using a microdiffusion technique followed by a pyridine-barbituric acid photometric finish. The determinable free cyanide includes hydrocyanic acid, ionic cyanide, and the cyanide of weak complexes such as cadmium, lead, manganese, and zinc cyanide. Complexes of copper, iron, nickel, and silver are sufficiently strong so the dissociation into free cyanide does not occur at the microdiffusion pH 7. Cyanate, sulfide, and thiocyanate do not interfere. Samples containing as little as 0.005 mg/L are successfully analyzed. The relative standard deviation is <10%. Samples stored at pH >I2 in the dark are stable at least three weeks.

Jan 1, 1981

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

By M. Ramokhothoane, S. Rupprecht

"NTRODUCTION Women employment in the mining industry dates back to the 19th century. Various parts of the world, for example, India, Japan, the United Kingdom and the United States of America had women employed in large numbers. The women’s jobs were primarily manual in nature. Women were used to carry coal in buckets from the coal face and out the mine, and those who worked on the surface plants were used to sort waste rock from the coal product. Other heavy industries, which were traditionally male dominated, for example the military, also had a considerable number of women supporting the war effort. The outbreak of war also caused a shortage of labour, which in turn, necessitated that women were used in various roles during the war. After World War II, women returned to their traditional roles, but had acquired new skills, and had a different outlook to life. The wearing of pants and short hair became fashionable, as a result of being in the army.Various laws were passed which prevented the employment of women underground. Different countries had rules that they believed were in the best interest of women and were of the opinion that the rules somehow were protecting women against the harsh working conditions. In South Africa, post 1994, there has been a shift in thinking in regard to the employment of women in the mines. WOMEN IN SOUTH AFRICA MINING In the words of the Minister of Women in the Presidency, Minister Susan Shabangu, “women must take centre [sic] stage as the country gears itself for the implementation of radical socio-economic transformation policies and programmes in the next five years” (SA Government News Agency, 2014). In as much as some progress has been made in advancing women, more needs to be done in order to realize sustainable benefits in the economy. The emancipation of women is a reality and remains top of the South African government agenda. From the Authors’ experience there are two types of men in the mines. The first group support change and see the value in it. To them, women in mining bring in the diversity and play the complementary role in achieving greatness. There is no fear of job security and humiliation but a great sense of “camaraderie”. The other group continues to enforce stereotypes, which works against the spirit of redressing the imbalances of the past."

Jan 1, 2018

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in intensified efforts in inspections of coal refuse sites by the Mining. Enforcement, and Safety Administration (MESA). MESA inspections however, are mainly qualitative and are often time consuming, Therefore, in August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in MESA inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photo interpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Based on CH2M HILL results cost for monitoring by rapid system was approximately 25 percent of cost by conventional ground survey.

Jan 1, 1980

By G. Coombs, L. Meade, J. Welshimer

Industrial Minerals commodity profiles are continued from May&apos;s Annual Review issue. Diatomite G. Coombs, Manville Sales Corp. Growth in US diatomite production continued to lag in 1986. The US Bureau of Mines estimated that 580 kt (640,000 st) were produced last year. This is a 1%0 growth over 1985. The cumulative growth from the 1982 low point is 4.4%. Present production, though, is still only 90% of the high tonnage of 1979. The industry will see increased competitive activity with the start-ups of two new mines and production facilities in California and Oregon. US production has come primarily from Lompoc, CA, Bassalt, Clark Station, and Lovelock, NV, and Quincy, WA. New production, probably with capacities of 45 kt/a (50,000 stpy) each, have started near Burney, CA, and Vale, OR. Eagle Picher&apos;s new, full-line filter aid and filler plant at Celatom, Vale, OR, was dedicated in August. The plant uses diatomite from the Celatom mining district in Juntura, OR. Grefco&apos;s new filter aid and filler plant near Burney, CA, was ready in July. It produced flux calcined products through a single kiln and can handle both bag and bulk shipments. The operations are in Shata County with the plant and mine at the same site. Manville Specialties Group is moving its Filtration and Minerals Division headquarters and research staffs to Lompoc, CA. The move is intended to strengthen response and performance by locating research, marketing, and production close together. Diatomite is processed in three methods: natural, calcined, and flux calcined. The natural is dried to remove water and is particle size classified. Calcined or straight calcined products have been sintered to modify particle size or permeability. Flux calcination, or flux sintering, has a stronger influence on permeability and also benefits color. The unique structure of diatomite is used in a range of particle sizes from fine paint fillers, to coarser filter aids, to granular aggregates. Dimension stone L. Meade, Geomapping Associates Ltd. 1986 was another good year for dimension stone production. The trend toward using marble, granite, limestone, sandstone, and slate has created an increasing demand. According to US Bureau of Mines 1986 estimates, 1.1 Mt (1.2 million st) of dimension stone, with a value of $173 million, was produced by 200 companies. This is an increase from 1985, where 220 companies produced 1 Mt (1.12 million st) valued at $172 million. The increased production volume and decreased unit value is due to the competition from imports. The net import reliance in 1986 was 68% compared to 62% in 1985. The value of imports was $374 million in 1986 versus $295 million the year before. In an effort to maintain their market share, domestic finishers, particularly in the granite industry, continued to upgrade plants and machinery during 1986. In addition, offshore dollars have financed a number of fabricating facilities in North America that will finish imported rough stock. It is hoped that this increased domestic production capability will capitalize on a devalued US dollar. The trend has been for growth in stone usage and market. This trend is continuing with increased public awareness and desire for natural stone in buildings. The area of greatest market growth is expected to be in residential and interior decorative stone usage. Use of sophisticated, automated equipment has made the cost more affordable. Now lobbies, foyers, and specialty rooms are being clad in stone. Dolomite J. Welshimer, National Lime & Stone Co. About three-quarters of dolomite production is used as construction aggregates and 10% to 20% is sold or used as an industrial mineral. Total limestone and dolomite consumed for chemical and metallurgical purposes is about 136 Mt/a (150 million stpy). Sales of industrial dolomitic products were somewhat stronger in 1986 than levels recorded in the early 1980s. Some of the sales&apos; strength, however, can be attributed to reductions in the number of active mining and processing operations. The industry will probably undergo further consolidation by the end of this decade. This will be due primarily to the continued softening in demand by the steel industry. Dolomitic limestone deposits being mined for raw materials for the steel, glass, and refractory in¬dustries are generally 54% calcium carbonate and 45% magnesium carbonate by weight. Impurities composed of silicon, aluminum, iron, sulfur, and phosphorous, represent less than 1%. The heaviest concentration of high purity, surface mineable dolomite in the US is in northwestern Ohio. Crushed and sized dolomitic limestone is a basic raw material for the iron and steel industry. It is also used as feed stone or lime kilns. Soft-burned lime is a popular raw material for BOF steel production. It is also used extensively in insulating glass fiber manufacturing. A related material, hydrated

Jan 6, 1987

By Zoë Mullard

The introduction of Web 2.0 platforms (also referred to as social media), with their architectures of participation, has ushered in a new era of technological interaction and information exchange that is changing the nature of corporate-community communications. Web 2.0 platforms give users the ability to generate data collaboratively, meaning that more stakeholders maintain the expectation of being able to contribute to online dialogue. In light of these changes, it is important for business to consider how social media can be used strategically to enhance stakeholder relationships and increase business efficiencies. This article provides three case studies of how different stakeholders in the mining industry are strategically using Web 2.0 platforms to communicate with target audiences. The case studies are based on the experience of respondents and from website observations, which were undertaken as part of a thesis research project by the first author (Mullard, 2010), focusing on the application of social media in the mining industry.

Jan 1, 2011

By Floyd C. Bossard

In underground mining operations, the over- riding issue has to be protection of worker health and safety. The employees underground, making a living in a dangerous occupation, know these are major issues. These men bargain their lives and health on the presumption that the operating management knows its business, and they, the underground employees, can pursue their occupation with the assurance that management has provided a safe and healthy ambient underground environment. When management assumes the mantle of protection of underground workers, it has to be positive that qualified engineers have designed the project, and that capable operating personnel are in charge and always available. Those persons with these responsibilities must be knowledgeable in the engineering and occupational health aspects of sine ventilation. The ultimate function of a mine ventilation system is to provide a comfortable, healthy and safe ambient environment for the underground workers. The attainment of these objectives has been complicated with the increased application of electrical equipment and diesel-powered mechanized mining equipment underground (discharging toxic diesel emissions); increased production rates with the attendant increased production of airborne dust; and mine development in increasingly hostile mineral formations containing combustible strata gases, radon gas emissions, along with high heat and humidity. In general, the modern mechanization of present mining operations has resulted in a sore complex set of problems for the engineer planning the underground ambient environment.

Jan 1, 1983

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995