Search Documents

By Steve Kral

A few months ago, Congress passed, and President Bush signed, a national energy bill. Designed to decrease the nation’s dependence on foreign sources of energy, the bill earmarked several billion dollars to increase the use of U.S. coal reserves. The bill also modified permitting regulations to speed up development of the coal reserves located on federal land. Coal currently supplies more than half of the nation’s electricity needs. And as housing starts continue to in-crease and with the nation’s appetite for electronic gadgetry, the demand for energy in the United States will only go up. That means coal producers must expand production while at the same time containing costs so they can enjoy this period of improved coal prices.

Jan 1, 2005

By J. Wiese

Recently the operating philosophy at concentrators processing platinum bearing ores has started to move from a recovery dominated system to one in which the production of high grade concentrates at the expense of some recovery would provide greater benefits in the further upgrading of the platinum group minerals (PGM). The low grades usually obtained are associated with the presence of naturally floatable talcaceous gangue minerals in all PGM ores. Polysaccharide depressants such as guar gum and carboxymethyl cellulose (CMC) are used to improve the grades of the concentrates. Recent testwork has shown that the use of high depressant concentrations can prevent any naturally floatable gangue from reporting to the concentrate. The only gangue present in the concentrates would be due to its entrainment in the froth. Under these conditions much higher grades can be achieved. The sulphide minerals themselves, however, become susceptible to depression at high depressant concentrations. This work examines how the recovery of sulphide minerals in two Merensky ores was affected by the type and concentration of the collector in the presence of high depressant concentration (500 g/t) and that the response of the sulphide minerals was also dependent on the type of depressant used (guar or CMC).

Jan 1, 2009

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By Dean Brox, Jason Morrison, Peter Procter

The Galore Creek Mine project is one of the newest major mining projects underdevelopment in Canada. The project is located in a very remote area of northwester British Columbia and is being developed by Nova Gold Resources of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site anew 120 km road is planned to be constructed including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1,200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipeline. Structural portal canopies have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works are to commence prior to any other works at the mine site and will be constructed entirely by helicopter support. Geotechnical investigations commenced in the summer of 2006 with the removal of the overburden materials at the portals to assess bedrock conditions. Tunnel construction from both portals is expected to commence in the spring of 2007. The construction of the mine project is subject to and awaiting environmental approval in the spring of 2007. The mine access road tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed.

Jan 1, 2007

By R. Switalski, M. Schafer, R. Pintabona, M. Kritzer, B. Lukajic, S. Janosko

Methane gas caused an eight-month shutdown of mining operations at the Mill Creek, Phase 3, Tunnel. The gas-related shutdown occurred as the tunnel was advanced to an approximate distance of 2,700 feet, which constitutes approximately18% of the total tunnel length. The construction of an emergency ventilation shaft, a comprehensive program of de-gassing wells and an expanded gas monitoring system were used to mitigate the gas condition. When complete, this tunnel will be utilized to convey and store combined storm and sanitary sewage collected from a portion of Cleveland, Ohio and ten suburbs. This paper will provide an overview of gas related remedial measures and explain how these measures were integrated into the project to ensure safe tunneling conditions.

Jan 1, 2007

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

By J. B. Rasmussen

As part of a purchase of a fleet of Caterpillar 785 trucks, Round Mountain Gold Corp., Cashman Equipment Co. and Caterpillar Inc. entered into a four-year contract for the major maintenance of the fleet of trucks. This contract includes fixed costs and guaranteed availability. The results have been excellent, and the fleet of trucks performs well. History The Smoky Valley Common Operation is a unique mine. Through a mixture of diligence and foresight, it has become the largest open-pit, heap leaching gold mine in the world. This was no small feat considering the remote area surrounding the mine. Round Mountain is located in north-central Nye County, NV. To the east of the town and mine lies the Central Toquima mountain range. To the west is the Toiyabe mountain range. Between them is the Big Smoky Valley, a flat expanse of sagebrush, salt grass and fine dirt.

Jan 1, 1991

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

By Dean Brox

The Galore Creek Mine project is one of the newest major mining projects under development in Canada. The project is located in a very remote area of northwestern British Columbia and is being developed by NovaGold Resources and Teck-Cominco of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site a new 120 km road is required including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipe-line. Structural portal canopies and portal houses have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works have commenced prior to any other works at the mine site and will be constructed entirely by helicopter support. The tunnel works commenced in the summer of 2006 with the advanced excavation of the overburden materials at the portals. Tunnel construction from the North portal commenced in the spring of 2007. When completed, the mine access tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed along with a construction status update as of late 2007.

Jan 1, 2008

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By J. Burgess Winter

It is an honor to present the lecture in honor of Daniel C. Jackling, the developer of the technology of copper mining that we continue to use 100 years later. He made a dramatic breakthrough in the early part of this century in the development of bulk-mining methods for large, low-grade porphyry copper-sulfide ore bodies. At Magma Copper, we are particularly proud that the Jackling Award states we have "made significant contributions to technical progress." Before Jackling's time, copper mining had exploited with primitive equipment very high-grade underground ore bodies and high-grade open pits. During the 20th century, the situation changed. Three significant innovations occurred within about 10 years around the turn of the century. In 1903, Jackling's concept of large-scale mining with steam shovels and rail haulage was implemented at the Bingham Canyon mine in Utah. Eighty years after the introduction of rail haulage, the mine converted to truck haulage with large-capacity high-efficiency haul trucks and reduced the stripping ratio from 3.5:1 to less than 1:1.

Jan 1, 1995

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020