Search Documents

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

From its early beginnings, shortly after the Witwatersrand gold rush of 1886, Randfontein Estates was planned as a heavyweight operation. The venture was capitalized by J .B. Robinson to the tune of £2 million at time when syndicates were loath to invest £50000 in ventures in and around the new metropolis, Johannesburg, which had sprung up midway along the Witwatersrand. But by then Robinson was a colossus among his contemporaries. Operating as a loner as he had done on the Kimberley diamond fields, where he created his own individual fortune and commanded the sort of respect which, early in his career, led to his election as Mayor of Kimberley. When news of a third gold discovery in the Transvaal (the first two had been in the Pilgrim's Rest and Barberton areas) reached Kimberley, Robinson's pioneering spirit was further stired and he hastened to the new goldfield to stake his claims before his business adversaries- Rhodes, John X. Meriman, Hans Sauer, and Caldecot-could entrench themselves. Once the new Witwatersrand goldfields had been proclaimed, claimpegging started in earnest. But the question was: where to start? Diamond men al, not one of the financiers had any knowledge of the geology of the gold-bearing formations.

Jan 1, 1989

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By J. M. Stewart

Mining fatality rates in many countries have not changed substantially over the past ten years. This demonstrates not only that there is an inherent risk in mining, but also that current approaches to improving safety need to be rethought. An analysis of productivity and fatality data in the United States, United Kingdom, and South 4frican coalmining industries shows that the impact of legislation on safety is overlain by other significant factors. Although improvements in safety and productivity usually occur together, the data warn that safety legislation can sometimes cause a significant reduction in productivity. Based on the data and experience considered, it is concluded that legislation should be aimed at creating a framework within which a positive attitude towards the implementation of more productive and safer mining methods, work practices, and technology can flourish, rather than attempting to enforce excessively prescriptive provisions. This later approach is even more problematic when safety standards and legislation are transferee from well developed to less developed countries. A legislative framework in which the mine manager is required to take al reasonably practicable measures to procure safe working conditions in accordance with mine-specific codes of practice is outlined. Within that framework, the value of adopting widely accepted standards is recognized. A performance-based external audit arrangement is outlined as a basis for ensuring that detailed attention is focused on those areas most needing improvement.

Jan 1, 1995

Council and Standing Committees, 1976-1977 President: Dr M. D. G. Salamon. Vice-Presidents: P. A. von Wielligh and Dr M. G. Atmore. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: Dr R. E. Robinson. Members of Council: J. D. Austin, E. Collier, C. T. Fenton, J. A. Holmes, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. T. Shaw, D. A. Viljoen, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: E. J. Jackson. Chairman, Orange Free StatelKlerksdorp Branch: A. N. Shand. B. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, V. C. Robinson, P. W. J. van Rensburg. Ten Council meetings were held during the year, and the standing and sub-committees held seventy-one meetings. Standing Committee Chairmen: Membership, Dr M. G. Atmore; Technical Programme - Metallurgy, J. A. Holmes ; Technical Programme - Mining, C. T. Shaw; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr D. G. Krige ; Awards, Dr R. E. Robinson; Excursions, C. T. Fenton; Adjudi¬cation, Dr R. E. Robinson; Constitution, Rules and Policy, Dr R. E. Robinson; Mines and Works, C. T. Shaw; Education, Dr R. E. Robinson; Pyrometallurgical Discussion Group (Convenor), Dr J. B. See; Phoenix National Committee, Dr R. E. Robinson.

Jan 1, 1978

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project's life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

By P. De Kock

Strategic mine planning is concerned with the decisions that determine the value of the business, while tactical planning deals with the tasks to realize that value. When tasked with formulating a strategic mine plan, the mining engineer often turns to commercially available software. However, these software packages have limited applicability to the RBM situation. Adopting a simpler, back to basics approach founded on a deep understanding of the economics of the orebody has the advantage of providing a clear logic to guide tactical planning. By creating a coherency between strategic mine planning, and tactical planning the likelihood of successfully executing the plans and attaining the value promised by the strategic plan is increased. This paper describes the reasons why RBM embarked on a strategic mine planning process, the rationale of choosing the process, and the process itself.

Jan 1, 2007

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By G. P. Dyke

The MRMR Classification System was developed specifically for mining applications, namely caving operations, and is one of three rock mass classification systems used in the South African mining industry today. Increased usage of the MRMR Classification System has raised concerns that it does not adequately address the role played by discontinuities, veins and cemented joints in a jointed rock mass. To address these concerns, Laubscher and Jakubec introduced the In-Situ Rock Mass Classification System (IRMR) in the year 2000. Although the IRMR System is more applicable to a jointed rock mass than the MRMR System, a quantitative comparison of the MRMR and IRMR Classification Systems indicates that there is not a significant difference between the resultant rock mass rating values derived from the two Classification Systems.

Jan 1, 2008

By L. Raaths

This paper outlines the process of improvement utilizing performance monitors and GPS systems on an opencast strip mine. Its primary focus is to maximize coal exposure by draglines and secondly to improve on those processes impacting directly on the dragline operation. The Aquila (DM2/5 system) navigation and monitoring systems were installed on the overburden drills. Their main function is to eliminate manual staking and positioning thereby ensuring a regular pattern being drilled. Holes drilled to planned depth reduce drill metres and it minimizes coal losses and contamination at the coal interfaces. The CAES (Computer Aided Electronic System) will be installed and evaluated on the Caterpillar D11 dozers at Optimum. This system ensures a correct dragline pad elevation through the use of planned elevations and GPS technology to achieve the optimal pad elevations for draglines consistently. The draglines are equipped with a Dragline & Operators Performance Monitor. This monitor allows the operator to control his own performance. It reports on all productivity, method and poor operating techniques. These monitoring systems send critical operational information back to the office. This source data resides in central databases from where it is converted and integrated into management information. To manage an operation means that you as a manager must be able to set objectives and targets and to achieve your goals the activities involved must be measurable.

Sep 1, 2001

By K. N. Karparov

The stress state on two slope profiles overlying an inclined surface with layer inclination of 50 and 150 are investigated. It is demonstrated that the induced stress state in an imbedded weak layer, exposed at the base of the slope, forms a zone of induced tensile vertical and horizontal stresses, which can lead to failure. The zone length depends on the slope angle and the angle of the inclined layers. L’état des contraintes sur deux profils en pente en superposition sur une surface inclinée avec une inclinaison de couche de 5o et 15o est étudié. L’étude présente démontre que l’état induit des contraintes dans une couche faible insérée, exposée au bas de la pente, forme une zone de contraintes de traction induites horizontales et verticales, qui peut amener à la rupture. La longueur de la zone dépend de l’angle de la pente et l’angle des couches inclinées. Die Druckvorkommnisse zweier Hangprofile auf einer schrägen Fläche mit einer Schichtneigung von 5º und 15º wurden untersucht. Es zeigte sich, dass die induzierten Druckvorkommnisse in einer eingebetteten schwachen Schicht, die am Hangfuße offen liegt, einen Gürtel induzierter vertikaler und horizontaler Zugkräfte bildet, die zum Zusammenbruch führen können. Die Gürtellänge ist von der Neigung des Hanges und der Neigung der schrägen Schichten abhängig.

Jan 1, 2003

By W. F. Nothard, J. R. C. Hill

The Rhodesian approach to the vegetating of slimes dams by J. R. C. HILL, B.Sc.(Agric.) (Visitor) and W. F. NOTHARD (Visitor) To prevent environmental pollution from mine dumps, it is necessary to stabilize them either mechanically or biologically. In the long term biological stabilization is more attractive because of its permanent nature. Initially, the basis of stabilization is in the correct siting and construction of the dump. The main toxic factors influencing plant growth on Rhodesian mine dumps are arsenic, antimony, copper, nickel, a high ratio of magnesium to calcium, excessive soluble salts, high pH, and Iow macronutrient content. Root-growth studies in culture solution and pot experiments are used to supplement information on the suitability of plant material obtained from replicated field trials on mine dumps. In addition to the selection of plants for toxic tolerance, it is advisable to provide multiple-layer protection with trees, shrubs, and grasses. Further, a range of different plant species gives greater biological stability. Protection must be provided for young plants against wind erosion and the abrasive effects of windblown sand. Planted wind breaks are preferred to mechanical forms; windrows of garden refuse make good wind breaks and at the same time introduce organic material to the dump and provide a good environment for seedling establishment. The use of artificial fertilizers and sewage effluent is recommended to hasten the development of a complete and protective plant cover.

Jan 12, 1973