Search Documents

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

It is well understood that to develop wagon wheels with higher abrasion resistance, fracture toughness, and fatigue resistance, steels with lower amounts of inclusions need to be used. Clean steels are produced with technologies that minimize the amount of inclusions in the microstructure. The demand for cleaner steels is high, and lowering of non-metallic oxide inclusions and controlling their morphology, composition, and size distribution is vital. Reduction of residual impurity elements such as sulphur, phosphorus, hydrogen, nitrogen, and trace elements is essential in the production of cleaner steel. Material cleanliness is vital for fatigue endurance, since oxide inclusions may act as stress concentrators and initiation points for fatigue cracks. To better understand the relationship between the cleanliness and toughness of the 34-inch cast wagon wheels, two samples of different levels of cleanliness were supplied for investigation. This paper presents the results of metallurgical analysis using scanning electron microscopy(SEM), energy-dispersive spectrometry (EDS), and mechanical tests for the pearlitic high-performance cast rail wagon wheel (identified as Class B) that are currently being used. The Charpy V-notch impact test results for the three samples from wagon wheels were compared. With the aid of SEM/EDS analysis system, non-metallic inclusions in these steels were detected, and it was possible to determine the position, size, shape, and composition of each particle. Alumina and manganese sulphide inclusions could be identified as the dominant inclusion types in the investigated samples. Fracture surface analysis of the Charpy specimen with high inclusions indicated that transgranular cleavage was the predominant fracture mode. Fractography of fracture surfaces of Charpy impact test samples also showed improvement of toughness properties on the clean sample.

Jan 1, 2013

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L'article décrit l'application des méthodes de modélisation continue/discontinue pour l'étude des conditions de stabilité de la mine d' Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d'estimer les conditions de stabilité de l'amas rocheux au terme de l'exploitation de la mine susmentionnée. La modélisation continue a impliqué l'application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By S. O. Castro, R. E. González, L. E. Velasco, J. M. Van Sint, P. V. Lois

Abstract Several zones with expansive rocks were encountered during construction of two tunnels of the water conduction system for the Chacabuquito Hydropower Plant, located in the Aconcagua river valley of the Chilean Central Andes Mountains, at elevation 1.075 m a.s.l., and 65 km north-northeast of Santiago. The expansive behavior was associated to three different geological features. Firstly with the crossing of important north-south trending faults, with montmorillonitic and caolinitic fillings. Secondly to the presence of zones of rock mass showing a penetrative presence of clay minerals (montmorillonite, illite and caolinite) and penetrative thin veins of ceolites. And thirdly to the hydrothermal alteration of the rock and the consequent generation of clay minerals (predominantly montmorillonite, sericite and minor caolinite). The geological and mechanical characteristics of the expansive rock domains, as well as the field and laboratory reconnaissance and characterization program, are described in the paper together with the bases for design and the guidelines for construction and definitive tunnels support. Resúmè Pendant l’excavation des deux tunels du système d’adduction d’eau pour alimenter la centrale hidroélectrique Chacabuquito, plusieures zones de rochers expansifs ont été découvertes. Ces tunnels sont dans la vallée du fleuve Aconcagua de la Cordillère des Andes du Chili Central, à une altitude aproximée de 1.075m s.m.n. et à 65km vers le nord-nord-ouest de Santiago. Cette conduite expansive est associée à trois différentes caractéristiques géologiques du massif rocheux. Un premier lieu, à l’intersection de plusieures zones de failles, d’orientation nord-sud et subverticales, avec remplissage de rochers désintégrés, montmorillonite, caolinite et sérite. En seconde lieu, a la présence de zones de rochers expansifs, avec des nombreux minces veines de céolite-calcite et aussi des minéraux argileux (montmorillonite, illite et caolinite). Et, dans troisième lieu, dût à la présence de zones d’altération hidrothermale du massif rocheux et la conséquente génération de minéraux de remplacement argileux (surtout sérite, montmorillonite et en plus petit degré, caolinite). Les caractéristiques géologiques et géomécaniques des rochers expansifs, ainsi que la reconnaissance du terrain et les résultats du programme d’essais de caractérisation géomécanique du laboratoire sont décrits dans ce travail, ainsi que les bases de dessin et recommandations constructives pour placement du support définitifs pour ces tunnels Zusammenfassung Während der ausgrabung der zwei tunnels der wasserleitungssystem, um die Chacabuquito Wasserstromzentrale zu besorgen, wurden verschieden ausgedehnte gesteinadern gefunden Die beiden tunnels befinden sich im Aconcaguatal, wo der Aconcagua Fluss fliesst, auf einer Höhe von 1.075 m über dem Wasserspiegel und ca. 65 Km Nord-Nordest von Santiago entfernt, in mittleren Anden Cordillere (chilenische Gebirgskette). Drei verschiedene geologische merkmale dieser massiven gesteine können dieses ausgedehnte verhalten erklären. Erstens, hier befinden sich verschiedene und auch ganz wichtige

Jan 1, 2003

By K. M. Primrose

Electrical tomography has developed rapidly over the last few years in its sophistication and practical use to enable three-dimensional information on the distribution of phases within flowing mixtures to be observed1. This paper reviews the current state of application from the industrial perspective, drawing on applications case studies based on scaling studies in the laboratory right through to installations on plant. In the laboratory, applications have looked at scale-up of mixing2 processes involving gas-liquid and solid-liquid suspensions3 with a particular interest in verifying computational fluid dynamics simulations or in checking scale-up design4,5. In the processing plant, the circumstances are usually bespoke and may range from simple detection of the degree of homogeneity of a flowing mixture through to the need to measurement a sophisticated batch process such as crystallization, sedimentation, filtering and drying. Examples drawn from the chemical and pharmaceutical industries will be presented and related to the benefits that can be gained through application of the method.

Jan 1, 2008

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1' section with the depth of 180 m and GS2-GS2' section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d'or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l'intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l'analyse de la stabilité au moyen de la méthode d'équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1' avec la profondeur de 180 m et la section de GS2-GS2' avec la profondeur de 150 m dans l'aire d'étude, nous mîmes l'hauteur du gradin à 10 m et 15 m, et l'angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d'examen a indiqué que il pourrait être propre de mettre l'hauteur du gradin à 10m et l'angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1' mit der Tiefe von 180 m und GS2-GS2' mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003

By X. Jia

The ability to perform three dimensional imaging at micron-scale resolution of real mineral floc sediments and structures using commercially available Micro X-ray Tomography (XMT) instrumentation can be used for the analysis of aggregates and granules, liberation and dewatering of sediments. This paper presents are view of recent work by the authors relevant to the mining and minerals industries. It covers three main topics: X-ray imaging of agglomerates and multi-component mineralic particles,, permeability of sediments, and dissolution of granules with potential application to heap leaching.

Jan 1, 2008

The peak in Sulphur price late 2008 caused again intensified investigation into the decomposition of sulphates and spend acid. One option is the recycling of sulphur from spend acid, which already started more than 40 years ago in the field of spend acid from organic processes in refineries and acrylic glass manufacturing. Since this acid couldn't be neutralized and discarded due to high organic contents, another source of SO2 to produce sulfuric acid is the decomposition of metal sulfates. The decomposition of metal sulfates was investigated at the next peak in Sulphur price in the 80?s. The first major scale pilot tests and studies of gypsum decomposition were carried out for clients in Florida. The decomposition of gypsum was quite often mainly influenced by the strategic decision of some countries to get own and independent acid production. In other cases the industry doesn?t have enough space to dump the gypsum. Therefore the company was also forced to convert the gypsum into ?saleable? products to avoid these residues. Other projects were made for the recycling of iron-sulfates from the pigment industry. The motivations for these projects were not only given by acid price. For the German pigment industry it was no longer permitted in the 80?s to dump the iron sulphate residues into the sea. These regulations forced the industry to develop new technology, which allows converting of the FeSO4-residues into iron oxide and acid. Therefore economical and mainly environmental factors influenced the decision of the companies to develop and to build these plants. Beside the above mention iron- and calcium-sulphates many other process exist, which produce metal sulphates as an intermediate product. These cases are not forced by environmental or strategic factors. In cases like Ni, Co or Mn-decomposition the main product of the plant is treated in the decomposition plant and later on used as ferrous-alloys. These final products are higher in price compared to e.g. CaO, which exclude the high-energy consumption for the endothermic chemical decomposition reaction. The reaction of SO2 generation based on acid or sulfate decomposition takes place in the range of 1000°C. The energy demand of the endothermic reaction is considerable and leads due to the high fuel-combustion off-gas stream to a diluted SO2 gas. Energy prices are usually increasing at the same time like sulphur. Sulphuric Acid based on decomposition is therefore more expensive than as acid based on sulphur combustion. The paper describes fluid bed technology and possible process concepts for decomposition plants. Additionally the thermodynamic background of the decomposition process and the main influence factors are provided to receive a better understanding of this technology.

Jan 1, 2009

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

The peak in Sulphur price late 2008 caused again intensified investigation into the decomposition of sulphates and spend acid. One option is the recycling of sulphur from spend acid, which already started more than 40 years ago in the field of spend acid from organic processes in refineries and acrylic glass manufacturing. Since this acid couldn't be neutralized and discarded due to high organic contents, another source of SO2 to produce sulfuric acid is the decomposition of metal sulfates. The decomposition of metal sulfates was investigated at the next peak in Sulphur price in the 80?s. The first major scale pilot tests and studies of gypsum decomposition were carried out for clients in Florida. The decomposition of gypsum was quite often mainly influenced by the strategic decision of some countries to get own and independent acid production. In other cases the industry doesn?t have enough space to dump the gypsum. Therefore the company was also forced to convert the gypsum into ?saleable? products to avoid these residues. Other projects were made for the recycling of iron-sulfates from the pigment industry. The motivations for these projects were not only given by acid price. For the German pigment industry it was no longer permitted in the 80?s to dump the iron sulphate residues into the sea. These regulations forced the industry to develop new technology, which allows converting of the FeSO4-residues into iron oxide and acid. Therefore economical and mainly environmental factors influenced the decision of the companies to develop and to build these plants. Beside the above mention iron- and calcium-sulphates many other process exist, which produce metal sulphates as an intermediate product. These cases are not forced by environmental or strategic factors. In cases like Ni, Co or Mn-decomposition the main product of the plant is treated in the decomposition plant and later on used as ferrous-alloys. These final products are higher in price compared to e.g. CaO, which exclude the high-energy consumption for the endothermic chemical decomposition reaction. The reaction of SO2 generation based on acid or sulfate decomposition takes place in the range of 1000°C. The energy demand of the endothermic reaction is considerable and leads due to the high fuel-combustion off-gas stream to a diluted SO2 gas. Energy prices are usually increasing at the same time like sulphur. Sulphuric Acid based on decomposition is therefore more expensive than as acid based on sulphur combustion. The paper describes fluid bed technology and possible process concepts for decomposition plants. Additionally the thermodynamic background of the decomposition process and the main influence factors are provided to receive a better understanding of this technology.

Jan 1, 2009

By J. Autio, H. Malmlund

The excavation damage zone (EDZ) caused by drill and blast excavation consists of intense damage adjacent to the remaining half barrel of the blast hole, new fracturing induced by the blast and reactivation of pre-existing fractures. The properties of intense microfracturing adjacent to the half barrels of remaining blast holes are based on study of rock samples from ZEDEX-tunnel and it’s extension at Äspö and the Research tunnel at Olkiluoto in Finland. The new and reactivated fracturing is based on results of mapping of slots cut in the rock in ZEDEX-project. The zone of increased porosity adjacent to half barrels, which penetrates to a depth of some centimeters was studied by using novel 14C-PMMA method. The penetration of the radial fractures, which is an order of magnitude deeper, was studied by mapping using color penetrant. Results of EDZ studies carried out at Äspö HRL in Sweden and in Research Tunnel at Olkiluoto show that the properties of EDZ can be affected significantly by engineering design. The result imply that the additional pore volume caused by distinct fracturing around the blast holes caused by state-of-the-art smooth blasting technique could be of the same order as that of the damaged zone adjacent to the surface of the half barrels. Durch Bohr- und Sprengarbeiten entstandene Eigenschaften der Auflockerungszone: Die durch Bohr- und Sprengarbeiten entstandene Auflockerungszone besteht aus einem großen, an das Resthalbrohr des Bohrloches angrenzenden Schaden, neuer Rissbildung und einer Reaktivierung der bereits existierenden Risse. Die Eigenschaften einer immensen, an die Halbrohre der Restbohrlöcher angrenzenden Mikrorissbildung beruhen auf einer Studie über die aus dem ZEDEX-Tunnel gewonnenen Gesteinsproben und deren Fortsetzung im Untertage-Labor Äspö (Hard Rock Laboratory, HRL) in Schweden und im Forschungstunnel bei Olkiluoto in Finnland. Die neue und reaktivierte Rissbildung basiert auf den Auswertungsergebnissen der Schlitze, die bei dem ZEDEX-Projekt ins Gestein geschnitten wurden. Die Zone der vermehrten, an die Halbrohre angrenzenden Porösität, die in ein paar Zentimeter Tiefe eindringt, wurde anhand der neuen 14C-PMMA-Methode untersucht. Das Eindringen der etwas tiefer gelegenen radialen Risse wurde anhand eines farbigen Eindringungsmittels untersucht. Die in Äspö und Olkiluoto durchgeführten EDZ-Studien zeigen, dass die EDZ-Eigenschaften wesentlich durch Engineering Design beeinflusst werden können. Das durch Bohrarbeiten verursachte Hohlraumvolumen der Rissbildung um den Tunnel herum ist ähnlich wie das Hohlraumvolumen der Bruchzone um die Bohrlöcher herum. Caractéristiques d’une zone endommagée par le creusement résultant d’un creusement par forage et dynamitage: La zone endommagée par le creusement résultant d’un creusement par forage et dynamitage présente un endommagement intense adjacent au demi-cylindre restant du trou de mine, une nouvelle fracturation et la réactivation des fractures préexistantes. Les caractéristiques de la microfracturation intense adjacente aux demi-cylindres des trous de mine restants reposent sur l’étude des échantillons de roche en provenance du tunnel ZEDEX et de son extension au laboratoire souterrain d’Äspö (« Hard Rock Laboratory » ou HRL) en Suède et du tunnel de recherche d’Olkiluoto en Finlande. La fracturation nouvelle et réactivée repose sur les résultats du placement des rainures sur la roche dans le projet ZEDEX. La zone de porosité accrue adjacente aux demi-cylindres et pénétrant à une profondeur de quelques centimètres à fait l’objet d’études recourant à la nouvelle méthode 14C-PMMA. La pénétration des fractures radiales, considérablement plus profondes, a été étudiée par placement en utilisant un agent pénétrant coloré. Les résultats des études EDZ effectuées à Äspö et à Olkiluoto montrent que les caractéristiques de l’EDZ sont susceptibles d’être affectées de manière significative par la conception technique. Le volume vide de fracturation résultant du dynamitage autour du tunnel est du même ordre que celui de la zone concassée autour des trous de mine.service.

Jan 1, 2003

By S. Tu, Y. Yuan, H. Wei, Z. Chen, M. Jia

"To reduce production costs and increase efficiency in ageing coal mines, a system that utilizes two shearers in a fully mechanized longwall working face is proposed. Using theoretical and engineering experience, three issues pertaining to the system were determined: (a) the two-shearer mining technique; (b) matching and modifying the equipment; (c) and coal-cutting task allocation for each shearer. Two mining processes are proposed, with the two shearers travelling in either the same or opposing directions. To avoid breakage of chains and pan extrusion of the armoured face conveyor (AFC), the length of the AFC ‘snake’ was controlled. To ensure continuous cutting and transporting of coal, the cross-sectional dimensions of the AFC were checked and the shearer closer to the head drive was modified. Based on the assumption of equal cutting times for each shearer, the meeting position of the two shearers was obtained by using a theoretical model of mining task allocation. Application of this technique at No. 2 Jining Mine, China, has shown remarkable benefits: daily production capacity was increased by 54% and personnel efficiency was improved by 33 t/d per person. IntroductionAll coal mines aim to increase the unit output of the working face to reduce mining costs and improve the economic efficiency of the operation. To achieve this goal, a production model known as one mining face of the mining area has been adopted by most Chinese coal mines (Hu, Meng, and Zhu, 2008; Zhang, Zhang, and Wang, 2000). Under these conditions, the main technical approaches to maximize the output are increasing the width of the working face (Qu, Xu, and Xue, 2009) and accelerating the advancing speed (Robbins, 2000). In coalfields with shallow seams, the width of a fully mechanized face exceeds 300 m (Ju and Zhu, 2015; Fu, Song, and Xing, 2010); in coalfields with deep seams, the width of the face is usually greater than 240 m (Liu et al., 2016; Li et al., 2013). The term ‘super-long working face’ was proposed to describe working faces with a width of over 240 m (Zhao and Song, 2016; Xu et al, 2007) in China. To support these long working faces with rapid advancing speeds, high-powered mining equipment is required (Kulshreshtha and Parikh, 2001, 2002; Tu et al., 2009; Mishra, Sugla,and Singha, 2013). This is easily achieved in newly built mines, but is not a good choice for ageing mines because of the low return on a high investment on account of the limited remaining resources. It is therefore difficult for ageing mines to significantly increase their unit output with the existing mining equipment. This study focused on this problem: two shearers were applied to a longwall fully mechanized working face (LFMWF) to achieve increased unit output."

Oct 1, 2018

By Willem J. Marais

The management of unpaved mine road networks on large surface mines rarely results in optimal road maintenance strategies and minimised total road-user costs. This is ascribed mostly to the complex and dynamic combination of variable road networks and loading and discharge points. In a dynamic mining environment - typically those mines in which production is managed by a centralised truck dispatch system ? there is no guarantee that a particular road maintenance intervention will contribute significantly to reducing total road-user costs or increasing productivity. Most large surface mines operating ultra-heavy mine trucks rely on an integrated on-board diagnostic data collation, communication and GPS-asset location system as a real-time fleet management tool. By extending this system to incorporate a multi-sensor analytical procedure in which specific truck vital signs are monitored and filtered, a road defect can be recognised and a trigger level set to relay the location of defects on the mine haul road to the centralised truck data management system. Previous work established the feasibility of the multi-sensor approach to road defect recognition on large mine haul trucks, and outlined the defect recognition, analytical and modelling issues and system limitations. This paper presents the development of the analytical procedure used as a basis for evaluating the truck on-board data to establish maintenance priorities amongst a network of mine roads. Following an introduction to the system architecture, the results of system field trials are analysed and the results discussed in the light of defect density and traffic volume as the primary variables in an approach to prioritising road maintenance. The paper concludes that by supplementing the existing mine communication and asset management systems, road maintenance can be managed on a near real-time basis and maintenance equipment dispatched to where most immediate benefit will realised from a maintenance intervention on the network, thereby generating the maximum improvement in service and reduction in cost per ton hauled.

Jan 1, 2008

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By J. H. E. Perry, V. H. Wiik

"The ore deposits of the Zambian Copperbelt occur in sedimentary strata that have been subjected to relatively mild, flexure-type folding. Unrolling serves to reconstruct the original depositional geometry of the folded sedimentary strata and is in common usage on the Copperbelt both for geological analysis of drill hole data and in routine ore reserve estimation.A computerized method of unrolling was introduced at Roan Consolidated Mines in 1969 based on a standard contouring program. A contour map of the geological structure is drawn from a regular grid of elevations, interpolated from the original, irregularly-spaced intersections. Unrolling is performed across this grid, perpendicular to one or two axes specified by the geologist. Each intersection is unrolled independently, and the new co-ordinates are subsequently processed to produce unrolled maps.The technique has been used successfully at RCM over the last two years in both the estimation of ore reserves and exploration planning."

Jan 1, 2014

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron's theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

Dr Hanekom I would like to thank Dr Hanekom for a very valuable -contribution; it summarizes careful statistical test work which was an omission from the original paper. Minor manipulative details, the application of a finer measuring graticule and the reproducibility of the procedure are described and the author accepts with gratitude this ready-made answer to the first and second points of Dr Finkelstein's comments. Mr Williamson The author is indebted to Mr Williamson for historical background to early experiments with captive bubbles and it is conceded that the original paper described another avenue to an old flotation goal. The field of application is restricted and we would not work with all the material illustrated by Klassen and Mokrousov.1 The particles in Figure 74(a) are far too large and irregular; material in Figures (b) through (d) could be employed for semi-quantitative work in spite of obvious disadvantages; Figure 74(f) represents ideal conditions. We have studied this mineral-collector association in the size range given and results were satisfactory. For larger pick-up values than that illustrated an induction period of more than 0.01 second was required (actually 90 seconds for a maximum bubble load at pH 7.2 with 25 g/t oleic acid!). REFERENCE 1. KLASSEN,V. I. ANDMOKROUSOV,V. A., 'An Introduction to the Theory of Flotation,' Butterworths, London, 128, Figure 74, (1963). Mr Slander and Mr Kooij Researchworkers in a practical mineral development laboratory may well ask what contribution yet another micro-technique can make to the problems of large scale ore flotation. The obvious answer is that there can be little or no direct translation of results obtained with a static system comprising air bubble and pure mineral concentrate to a dynamic multicomponent operation. However, for the rapid study of one mineral or variable some small scale apparatus must be employed. In the Anglo American Research Laboratory, the described semi-quantitative pick-up technique has filled a niche and requirement. For ourselves, the system represents a definite advance over the contact angle approach in that samples of minerals conventionally prepared in laboratory or plant may be used, which is a desired step nearer flotation. We bracket this pick-up apparatus with the Hallimond tube1,2 and evidence is now to hand that pick-up curves may often be related to flotation recoveries obtained from this tube with pure mineral samples and from the Fuerstenau glass cell3 with the total ore at low pulp densities. We would not wish to push the comparison of pick-up results past this stage for there is much published development work relating the Hallimond and Fuerstenau equipment to flotation on a larger scale. At the Anglo American Research Laboratory for example, a test in a Fuerstenau cell is often the final integrated step in laboratory investigations into the TORCO process. As these contributors rightly point out, pick-up tests can offer nothing towards the determination of optimum reagent dosage for large scale flotation. This is the function of bench-type flotation cells with up to 2 kg batches of ore. At this level, collector performance and consumption and physical properties of the froth are more comparable with large scale operation. The pick-up cell, Hallimond tube and Fuerstenau cell are essentially equipment from which the effect of control parameters can be derived. For the assessment of collector behaviour, the pick-up approach is rapid and economic and we offer here a pick-up contribution towards the flotation of Witwatersrand uraninite with anionic sulphonate collectors (Fig. 1). A large crystal of the local mineral was not available for contact angle measurements and owing to its low concentration in Witwatersrand gold-bearing reef, a small sample was laboriously obtained by tabling, superpanning and heavy medium separation. The pick-up values of a sized portion were determined by the described procedure in the presence of nine petroleum sulphonate collectors. Responses fell into two categories; "normal" curves (dotted lines) and a group of collectors which were very active at low concentration but showed depression of pick-up at the higher levels. The similarity in form of curves for collectors 1 and 3 was apparent and reagent 3 was found to be simply a diluent of 1. Otherwise, collector performance could not be related to either sulphonate content or molecular weight of the active constituent. However, reagent 2 gave the best performance in a bench flotation cell with regard to overall uranium distribution but, as predicted, reagent 1 yielded the best grades. Later pick-up tests with a similar class of collector have suggested that depression at high reagent concentrations may be due to "bubble armouring" whereby an hydrophilic air-liquid interface is produced which rejects mineral attachment. Prolonged investigations with the same mineral sample have not been required except for the study of uraninite which lasted for more than a year. Variation in pick-up response could not be detected over this period during which the mineral was stored under distilled water. The only visible change was a small efflorescence of lead sulphate, readily removed and decanted off after stirring with a glass rod in the sample tube. In its main role as a "trouble-shooter", the pick-up method is applied to fresh mineral samples taken from a flotation plant and soon discarded or from a current run in the ore-dressing laboratory. After production of a concentrate, a solvent cycle, as described in the original paper, may be required to remove heavy organics or other contaminants as when a sample has been taken from circuits containing detergents, grease or return flotation solutions. This solvent cycle will not remove chemisorbed collectors and we prefer not to work with minerals from flotation tailings or with pick-up cell discards. It has been thought preferable to answer the contributors' other apprehensions with regard to sample preparation, activators, depressants and the physical properties of reagents in another paper on offer to this Journal. It covers pick-up investigations relating to the flotation of nickeliferous pyrrhotite at two Anglo American Corporation Mines, which approach seemed the correct orientation for a reply to another contributor to this paper.