Search Documents

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By Fred D. DeVaney

The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron are annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply. Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment. These may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the "betterment" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the in¬tent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods non well under way than of extension of boundaries by the city block plan of growth.

Jan 1, 1932

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By J. E. Schiller

The Bureau of Mines is investigating methods to treat waste water that contains cyanide. This report describes a new method that removes heavy metals and all forms of cyanide. In the first step, hydrogen peroxide and sodium thiosulfate are added at pH 7 to 9 in a 1:2 molar ratio to convert free and weakly complexed cyanide to nontoxic thiocyanate. Then steryldimethylbenzylammonium chloride is added to precipitate ferro-cyanide, and finally, ferric sulfate is added as a sweep floc and sequestrant for heavy metals. After the suspended solids settle, the water is polished by filtering. The water initially contained 1 to 5 mg/L Fe, 1 to 5 mg/L Cu, and 10 to 30 mg/L total cyanide; the level of each of these constituents was reduced to less than 0.02 mg/L.

Jan 1, 1983

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993

By M. O. Magnuson

This publication describes abandoned-mine fire-control work administered by the Bureau of Mines under cooperative agreements with State and local governments. The work was done by private contractors under the supervision of Bureau engineers. The work is authorized by Public Law 738, approved August 31, 1954, and Public Law 89-4, approved March 9, 1965. Earlier work was authorized by Interior Department Appropriations Acts for fiscal years 1949-55. A total of 70 fires have been controlled under this program in the eastern bituminous region. The nature and extent of the abandoned-mine fire problem in the bituminous region is discussed, and the methods used for controlling these fires are described. The methods that have been used, either singly or in combination, include loading out and cooling the burning material, installing fire barriers, surface sealing, and water and pneumatic flushing.

Jan 1, 1974

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concen¬tration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidaticn practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By Oliver Q. Leone

Electrorefining tests using titanium-nitrogen alloys as anode material showed that no significant quantity of nitrogen was transferred to the cathode deposit. The nitrogen of the anode remained in the scale, and the titanium-nitrogen alloy was anodically insoluble in the electrolyte when the nitrogen content was 11 weight-percent.

Jan 1, 1966

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By W. L. Falke

Research was conducted to develop methods on a laboratory scale for recovering manganese from manganiferous slimes and limestones . The procedure is a low- temperature modification of the carbamate process , in which manganese is dissolved and the valence reduced by treating slimes and limestones with controlled amounts of sulfurous acid . Manganese ( II) hydroxide is precipitated and leached with ammonium carbamate solution , and manganese carbonate is separated by warming the leach solution . A major portion of the reagents is regenerated and recirculated . About 75 percent of the total manganese in manganiferous slimes , and from 50 to 75 percent of the total manganese in manganiferous limestones , are recovered as manganese carbonate containing 45 percent manganese .

Jan 1, 1964