Search Documents

By J. L. Dion

"A study of the techniques to integrally cast copper tubes in copper tuyeres for use in blast furnaces has been carried out. The work has been performed in support of current efforts to produce two-compartment tuyeres having improved water-cooling capacity. A test pattern corresponding to a vertical section of a two-compartment tuyere, and including a cast-in-place copper tube, was used to investigate such variables as tube preparation, tube coolant, pouring temperature, pouring rate and gating design. Successful castings, either with a good metalfurgical bond or good intimate contact between the tube and the casting, were produced, with all combinations of gating system and position of the tube tried. However, the pouring temperature, the pouring rate and the effectiveness of the coolant are interrelated and must be controlled to produce a good metallurgical bond.IntroductionAs part of its contribution to, and in collaboration with, the Copper Casting for the Steel Industry Committee, CANMET has undertaken research into the methods and techniques needed for the integral casting of copper tubes into high-conductivity copper castings.The objective was to produce two-compartment copper blast furnace tuyeres in which the water-cooled nose compartment consists of a copper tube metallurgically bonded to the wall of the high-conductivity copper casting. This design, developed in the UK, has demonstrated a much extended service life with attendant economies; unscheduled shutdown of blast furnaces due to tuyere failure is a significant problem in the steel industry. The Canadian steel industry believes that this design will replace the currently used single-compartment tuyere in blast furnaces within a few years.The technology to produce these tuyeres does not exist in Canada. One of the main features is the inclusion of a smooth-walled cooling channel in the nose, which permits high velocity cooling water to be employed. A second compartment acts as a reservoir backup, should failure in the nose occur. This would allow continued use of the tuyere for a period of time, permitting a scheduled shutdown for repair s. To assist the Canadian producers of tuyeres to maintain their market, and the Canadian steel industry to have a reliable domestic supply, it is important that the necessary technology for the production of two-compartment tuyeres be developed and transferred to industry."

Jan 1, 1982

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By D. Marotte, M. David

"A new exploration procedure is proposed for volcanogenic massive sulphide deposits of the Abitibi belt. ""Samples"" of acidic volcanic rocks (Si02 > 60%) were compiled from the literature. From the 574 samples collected, 322 were used in each of a number of experiments. Forward inclusion linear discriminant analysis performed on the untransformed geochemical data shows a general depletion in Na20 and CaO along with an enrichment in MgO for a ""proximal"" group of samples relative to a ""distal"" one. The percentage of misclassified samples reaches 20% to 30%, but test sets shows good stability.The exploration procedure was applied to the Normetal deposit, where the authors took 160 samples during the summer of 1977. It quickly leads to the definition of targets for more detailed exploration together with a good recognition of the old known deposit.IntroductionVolcanogenic massive sulphide deposits in the Abitibi belt (Quebec) are mainly found in rhyolites or acidic pyroclastics in the uppermost portion of a calc-alkaline volcanic series (Descarreaux, 1972). The deposits are thought to have formed syngenetically by the action of volcanic hydrothermal exhalations during the waning episode of a felsic volcanic cycle (De Rosen Spence, 1976). Alteration pipes of disseminated sulphides are commonly present. Metal deposition from hot springs, initiating convection cells in a submarine environment, may have been the dominant process in ore formation (De Rosen Spence, 1976)."

Jan 1, 1981

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By N. E. Chaouai, M. Lavigne

"Indicator kriging is one of the non-parametric geostatistical techniques, ideal for estimating the reserves of irregular mineralizations (e.g. gold, uranium, platinum, diamonds, etc.). Such mineralizations are characterized by variograms which are very sensitive to extreme values (outliers) and very difficult to model.The classical approach to this problem in the industry is to trim off these high grades using arbitrary empirical upper limits established either from practice or subjectively. Contrary to this simplistic approach, indicator kriging discretizes the histogram of the grades (usually log normal) in several classes and carries out interpolation separately for each class. This paper gives an overview of the differences between ordinary and indicator kriging along with the steps required to carry out indicator kriging. The paper concludes with a case study involving a gold deposit estimation.IntroductionParametric geostatistics (ordinary kriging) has given us satisfactory results over the years in estimating the reserves of well behaved deposits with coefficients of variation close to 1 (e.g. sedimentary and porphyry type deposits). However, numerous problems have been encountered in estimating irregular mineralizations (e.g. small vein deposits of precious metals) with high coefficients of variation in the range of 2 to 5. Such deposits are characterized by a very small proportion of extreme values (outliers) which create distortions on the variograms (pure nugget effect) and render them useless(1,2).The solution often followed by the mining industry today is to trim off these values based on empirical limits. These limits are derived either by comparison with production results (or bulk samples) or by geological interpretations. Needless to say that such manipulations can lead to serious errors in estimating ore reserves (usually underestimation of total metal quantity), especially when production results or bulk samples are absent.On the other hand, the solution followed by the geostatisticians in the past was to smooth out the data using transforms (e.g. normal-score or natural logarithms). Such transforms are nonlinear and they required non-linear estimation techniques such as disjunctive kriging (DK) or multivariate gaussian kriging (MG) which require normal related hypotheses, not necessarily true in geology.Nonparametric geostatistics (indicator and probability kriging) have been -developed in order to handle these problems related to highly skewed distributions."

Jan 1, 1990

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By G. J. Kipouros, P. W. Kingston, W. F. Caley

"Current practice in advanced materials processing has involved the dispersion of a second-phase, commonly SiC, glass, or other non-metallic fibres/whiskers/particulates to enhance physical characteristics of the matrix. These matrices may be either ceramic or metallic but in either case it is important that the physical and chemical properties of each phase be compatible. The dispersed, finely divided second phase is often both expensive and foreign-produced and may exhibit chemical instability at elevated temperatures. Thus, it would appear that certain naturally-occurring industrial mineral fibres/whiskers/particulates might offer an attractive and low-cost alternative. Suitable candidates, such as wollastonite and sillimanite, are available in Canada and may be milled to produce particles whose shape is appropriate for this application. It is suggested that wollastonite, in particular, may be a useful modifying agent in metal matrix composites utilizing AI, Al-Si, Zn-Al or other light metals and alloys. In addition, the possible use of these minerals in ceramic matrix materials is also addressed, with reference to a preliminary thermodynamic analysis of the systems involved.IntroductionBackgroundA composite material may be thought of as consisting of a matrix component, the properties of which are improved by the addition of a second component or dispersed phase which forms a distinct three-dimensional interface with the matrix. This matrix is commonly either metallic or ceramic, which leads to the two most popular types of composites: metal-matrix composites (MMC); and ceramic-matrix composites (CMC).Such materials are by no means new. Early composites include fiberglass, mixtures of plaster and horsehair in wall plastering, as well as use of natural materials such as bamboo in fishing rods. Some of the newer applications include high strength, low-weight bicycle rims, as well as the more familiar role in aircraft and automobile engine components."

Jan 1, 1993

By B. Stuckert, P. Sheehan, J. Balfour, B. (Manas) Das, D. Fawcett

"With the growth of large scale surface mining operations, waste disposal and stability of waste dumps pose a challenging problem to engineers. Vibrations due to blasting operations proximal to these dumps further complicates dump design. Many dumps which are statically stable may become unstable due to the effects of blasting vibrations.A joint project between CANMET and Smoky River Coal Ltd. has been initiated to study the dynamic stability of waste dumps. The study involves development of an analytical algorithm combined with field monitoring to assess dump performance.Another objective of the study is to provide baseline data for a vibration attentuation relationships for sedimentary rock (coal) environments: most studies to date are for base metal mines. The effect of dump thickness on vibration response is also addressed.The key objective of the study is to present a methodology for assessing the dynamic stability of waste dumps. Implicit in this methodology are a number of assumptions concerning vibration attenuation in sedimentary rock environments, and response of the dump material to induced vibration. Where possible, these assumptions have been compared with monitoring data as a check on their validity."

Jan 1, 1989

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By G. E. Norman, R. E. Michelutti

"One of the major objectives of Falconbridge has been and continues to be, to minimize the impact of its operations on the environment around its Sudbury operations.The approach to achieving this objective and the results, are discussed under the following topics .I . Sulphur Dioxide Emission Improvements.2. Effluent Treatment Improvements .3. Effect of the Envrionmental Improvements.Sulphur Dioxide Emission ImprovementsHistoryThe rejection of pyrrhotite in the concentrators is one method of reducing the amount of sulphur to the smelter and therefore the sulphur dioxide emissions. In the 1950s and 1960s, Falconbridge developed the capability to remove 54% of this pyrrhotite. Numerous attempts were made to increase this amount by treating the pyrrhotite for recovery of nickel and in some cases elemental sulphur. Processes tested and operated were: hydrometallurgical pilot plant, roast-leach commercial operation and nickel-iron refinery. None of these processes proved to be commerically successful for both technical and economic reasons. Falconbridge therefore redirected its efforts to reducing sulphur emissions by improving its smelting process under The Smelter Environmental Improvement Project. A major component of this project was the installation of a sulphuric acid plant to recover the S02 in the roaster off-gases."

Jan 1, 1984

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs' Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By A. C. Moerman, C. W. Pelley, K. R. Notley

"The software package described in this paper facilitates the handling of diamond drilling information in the creation and maintenance of a geological information database. Once entered, the drilling information is stored in a direct access file for rapid retrieval. The drill data are sorted into vertical cross sections and interpretation is performed using on-screen menus to define areas of common rock type and outline the mineralized zones. Intersections of individual zones can then be examined and outlined in the longitudinal dimension at a graphics terminal.With the aid of surface-fitting routines, the digitized information can be used to generate three-dimensional models of each zone. From these models intermediate cross sections and level plans can be obtained. Several interpretations are possible and plotter drawings can be obtained. An output file for use by ore reserve estimation software can also be created.Future work will tie this software to geostatistics and mine planning programs and will be aimed at converting mainframe software to run on microcomputers. IntroductionComputer applications in underground mine planning and geology are not new. Operations such as Sherritt Gordono and Kidd Creek have been using software developed about a decade ago for handling geological information and designing stoping blocks. However, general use of such systems has been limited mainly due to the cost of hardware which was affordable only to large corporations. Software to perform the work was usually developed on site and was largely unavailable for use by others, being site-specific, or too expensive for other organizations to purchase.The increasing power of microcomputers and mini-computers, and their relatively low cost compared to the mainframe computers which were previously used, has led to the increased use of computers at mining operations of all sizes. Sources of software for use in geological interpretation and mine planning have increased in number with the proliferation of the use of microcomputers."

Jan 1, 1988

By M. Nagamori, A. J. Plumpton

"A low-grade concentrate from the Crevier Township, Quebec, containing 1.8% Ta205 and 13.7% Nb205 was reduced with carbon at 1600°C, and niobium and tantalum were selectively absorbed in liquid iron. To slag off the zirconia-rich gangue, some silica and lime were added as flux. Metallic iron was added in such a way that the combined contents of TaC and NbC did not exceed 20% in the ferroalloy . Up to 95% of the niobium, and up to 80% of the tantalum contained in the concentrate were recovered in the metal. The ferroalloy was ground finely and dissolved in 2 wt % sulphuric acid to leach out iron and silicon preferentially. The insoluble residue consisted principally of NbC and TaC, the calcination of which yielded an enriched concentrate comprising 80% Nb2O5 and 8% Ta2O5. The insoluble residue could also be chlorinated to obtain an impure liquid of Nb2Cl5 and TaCl5. Process variables and their effects are discussed in terms of higher metal recoveries in the smelting.IntroductionPresently, about one-third of the world production of tantalum comes from the pyrometallurgical reprocessing of tin slag, a by-product of tin smelting, containing sometimes 2 to 10% Ta205 and about the same amount of Nb205. Upon heating tin slags with carbon at about 1600°C in an electric furnace, tantalum and niobium oxides are converted to TaC and NbC, which are absorbed by the coexisting phase of molten metallic iron(1,2). The Fe-Nb-Ta-C melts cannot be decarburized by oxidation because of the preferential formation of Nb and Ta oxides over CO gas(3). So, the ferroalloys containing tantalum and niobium carbides are commercially treated by acid-leaching and I or chlorination to eliminate iron and thus permitting the eventual recovery of purified tantalum and niobium oxides(2).Absorbing Ta and Nb carbides in molten iron was first proposed and demonstrated by Zimmerley and Back(4) in 1957 in order to recover selectively tantalum and niobium from lowgrade concentrates. The process was successfully applied to the electric furnace smelting of tin slags by Hunter and Fursmant(5) over a period preceding 1965."

Jan 1, 1985

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By G. H. Blackwell, A. J. Sinclair

"The main components of a ""PC” -based mineral inventory system are described in a sequence common to many real reserve/ resource estimation projects and in the practical context of problems and decision-making typically encountered in such studies. Some components are designed particuarly to improve the geostatistical instructional capability of the package. An important part of this approach involves the use of widely available software for data manipulation and evaluation in the design of a mineral inventory study progressing to mine design and feasibility. A variety of more or- less fixed routines written in high level languages provide acceptable computational speeds on a personal computer. These critical segments are linked by simple, short, compiled Basic programs easily adjustable to various data configurations and needs. IntroductionGeostatistical mineral inventory estimation has progressed greatly since its slow dissemination during the 1960s. The mining industry generally has accepted the benefits of the technique, notably the quantification of grade and geology, an indication of error in grade estimation, and of the mined volume / grade variance relationship (Clark, 1979, Isaacs and Srivastava, 1989).Acceptance has been slowed, first by complexities of geostatistical theory and second by a bewildering variety of computer systems and applications programs. Continuing improvements in education will facilitate a better understanding of the underlying theory.The purpose of this paper is to describe, in a practical context, the development of a geostatistical-based approach to reserve/resource estimation. The approach integrates various existing commercial software packages with a wide selection of programs developed by the authors for personal computers which estimate mineral inventories and educate users in the techniques applied; that is, the QMIN system.It is hoped that the approach presented here will convince mining and geological engineers concerned with resource estimation, of the soundness of geostatistical methods and its broad potential to their problems."

Jan 1, 1992

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By Hans D. Gougar

To meet an increasing demand for minerals, mining operations are moving to ever more remote regions. The lack of a local energy supply and infrastructure, coupled with social and regulatory demands for lowered environmental impact of mining operations, presents an opportunity for a seemingly unlikely competitor ? a nuclear power plant. The Modular Pebble Bed Reactor concept, currently in various stages of research and development around the world, offers a high degree of reliability and safety with minimal consequences for the local or global environment. The passive safety features of this design eliminate the need for the extensive active safety systems that add significantly to the cost of current water-cooled reactors. With the MPBR, as with all nuclear plants, there are no appreciable quantities of waste products released to the environment during normal operations. In contrast with conventional reactor designs, the MPBR would also remain radiologically safe even under the most severe abnormal circumstances. The key to the design is the fuel element. Enriched uranium microspheres are coated with various layers of pyrolytic carbons and silicon carbide to form a highly-temperature resistant particle that effectively retains all fission products. These particles are mixed with graphite and formed into 6 cm pebbles. A randomly packed vessel of such pebbles forms the reactor core through which helium is circulated as a coolant. Computer models and tests performed on actual pebble bed reactors confirm that fuel failure temperatures are not reached even during the most severe conceivable loss of coolant accident. The reactor drives a gas turbine cycle with resulting efficiencies as high as 48%, comparable to natural gas-fired units. The low price of uranium fuel and low maintenance requirements translates into competitive operating costs. However, high capital costs prevent the MPBR from competing with natural gas in most markets. In remote applications where no fossil supplies are readily available, the playing field is more level. This paper summarizes the features of two of the more promising candidates for remote applications and discusses the strengths of the MPBR from the perspectives of fuel supply and environmental impact.

May 1, 2002