Search Documents

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month's performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont's original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin's mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By Thomas C. Wilder, Walter E. Galin

Measurements of the electromotive force of the cell at 995°C have shown that the cell may be used to detennine the zinc content of molten Cu-Zn alloys to the nearest 0.05 wt pct. The cell is used for brass melts to which no ZnO is added intentionally, because essentially all oxygen in the Cu-Zn-O system is present in the form of ZnO. The cell is also used to detev,nine the thernodynamic activity of zinc for Cu-Zn al1oys of the brass composition range, from which the equilibrium partial pressure of zinc for such alloy may also be calculated. The electrochemical measurement of the concentration of the most active metal in other engneering- alloy systems by a similar technique is also considered. IN recent years there have been many studies concerning the direct electrochemical measurement of oxygen content in molten engineering metals.' These investigations employ galvanic cells in which the electrolytes are various solid mixed-oxides which conduct current by movement of oxide ion vacancies under the influence of an oxygen potential gradient. Similar cells have also been used to measure the thermodynamic properties of mixing of solid alloys,' one component of which has a much greater affinity for oxygen than the other component(s). One alloy system of obvious engineering importance comprised of two metals of greatly differing affinity for oxygen is copper-zinc. At the casting temperature of molten brasses, the zinc concentration is very difficult to control not only because its vapor pressure is very high, but also because of its high affinity for oxygen to form ZnO. Inasmuch as brass castings may be required to have a zinc concentration within very narrow limits, it would be advantageous for the brass industry to have a means for quickly measuring the zinc content in the molten alloy just prior to pouring. A calculation based on earlier thermodynamic studies of oxygen and zinc in dilute solution in binary Cu-O and CU-Z' alloys indicates that the oxygen concentration of molten 70 wt pct Cu-30 wt pct Zn brass must be much less than 1 ppm for the separate phase ZnO not to exist in the ternary Cu-Zn-O system. Thus it can be assumed that all molten brasses, both in the laboratory and in the foundry, are sufficiently saturated with oxygen for the separate phase ZnO to be present. In view of the foregoing reasons, the cell investigated at 995°C for the purpose of measuring the zinc concentration in molten copper-zinc alloys, particularly those of brass compositions. In this cell the left hand electrode is a reference electrode comprised of a mixture of the pure powders of nickel and nickel oxide, to which a platinum contact is made. The electrode of interest is a molten Cu-Zn alloy of unknown zinc concentration with a tantalum wire contact. The electrolyte is the commercially available (Zircoa) calcia stabilized zirconia. The ZnO in the Cu-Zn electrode compartment is not intentionally added, but is naturally present as a result of the infinitesimal amount of oxygen required for its formation in this alloy system. In cell [A] nickel oxide is reduced at the cathode where O= represents the electrolyte. At the anode dissolved zinc of the Cu-Zn alloy is oxidized to form ZnO(s) in its standard state Thus the overall reaction is for which the molar free energy change is where 5 is the Faraday equivalent (23,063 cal per v equivalent), is the electromotive force of the cell in volts after correction for the Pt-Ta thermocouple, FOf (ZO) and AFF (NO) are the standard molar free energies of formation of the respective oxides, and a2n is the thermodynamic activity of zinc in the molten Cu-Zn alloy. The reference state of zinc in this case is taken to be the pure liquid. At constant temperature all the terms of Eq. [I] are constant except and azn Thus since all other participants in the electrochemical reaction are in their standard states, the change in the electromotive force of Cell [A] is represented only by a change of the thermodynamic activity of zinc at constant temperature. The zinc concentration is related to the activity by sampling the alloy for chemical analysis after cell measurements are taken. EXPERIMENTAL A typical cell construction is shown in Fig. 1. This and other experimental details were similar to that described earlier with the exception of some minor modifications which are detailed below.

Jan 1, 1970

By W. B. Finkeldey, C. H. Mathewson, C. S. Trewin

This paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferraus metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such .an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties—and this we consider to constitute the clement~ of metal technology—might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary or survey of progress in the entire field as determined by varied experience, practice, and settled opinion.

Jan 1, 1921

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By C. Chiou, D. P. Seraphim

The effect of clustering on the superconducting properties of Al-Zn alloys has been studied by the ballistic induction techniques. The superconducting critical temperature, T,, changes when zinc-rich clusters are formed. The change in T, depends on the concentration and may be positive or negative, but always correlates with an effective decrease in the solute concentration of the alloy. Reversion after clustering effectively returns a 5 at. pct Zn alloy to the quenched state. These methods might be use&lly extended to the Al-Mg system, where X-ray data are difficult to obtain. In very dilute Al-Zn alloys, as in other tin,' indium, aluminum,2 or tantalums base solid solutions, there is a decrease in the superconducting critical temperature, Tc, roughly proportional to the temperature independent resistivity, i.e., -0.2°K per pS2cm. With increasing solute concentration, the T, generally reaches a minimum and then increases4 to a value well above that for the pure solvent. The change of T, with solute concentration follows an empirical formulation involving two constants which correlate with the scattering cross section of the impurities. As will be shown below, the Al-Zn alloys more concentrated than 1or2at. pct do not follow the empiricism, probably because they are unstable even when rapidly quenched.5 However, it seems possible to study at least the later stages of solute clustering by precise measurements of the 1', following various thermal treatments. A few experiments on quenched alloys, aged alloys, and tests on reversion are reported here. The heat treatments selected for obtaining the quenched and aged states were mainly deduced from the work of Dash and Fine.6 For the quenched state, specimens were homogenized at 480°C, quenched to -160°C, and immediately transferred and mounted in liquid nitrogen. Measurements on the superconducting properties and residual resistivities were then made at helium temperatures, after which the specimens were aged at room temperature for 3 to 5 hr, i.e., much longer than the time required for clustering to be essentially completed. The superconducting properties and residual resistivities were once again examined. To reach the reverted state of the A1-5at. pct Zn alloy, the aged specimen was heated for 5 min at 200°C and then tested as above.

Jan 1, 1963

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By J. R. Campbell

A dozen years or so ago, the general superintendent of our company, now the president, Mr. W. H. Clingerman, asked me to study the coal-washing problem. This work brought me into contact with the best washery men of the country. I investigated many kinds of coal-cleaning schemes, made numerous tests, and collected voluminous data, yet I confess frankly that I have had little practical washery experience and that little has been at the Middlefork washery of the United States Fuel Co. at Benton, Franklin Co., Ill., which was put in operation last fall. While this washery installation may not be the "last word," I am quite sure it embodies some long steps in advance of the older designs and constructions. From the washery man's standpoint, the removal of pyrites or marcasite, a disulfide of iron, is the one vital problem, and the one productive of the most beneficial results, so far as elimination of sulfur is concerned. Sulfates and so-called organic sulfur occupy quite a sec-. ondary position and are generally lost sight of in coal washing. The elimination of sulfur in coal in the past has usually been accomplished by jigging in water, but lately concentrating tables have been successfully employed. The flotation process has been applied to fine coal, but is hardly considered practicable. Coal washing is rapidly coming into its own, due to the depletion of low-sulfur coals for coking purposes, and we predict that soon the same careful attention will be given to the design and construction of coal washeries that is now being given to byproduct plants and other allied industries. Heretofore, coal washing has been considered only an incidental and necessary evil instead of the big problem it is—one worthy of the most careful study by men well trained along technical lines and capable of delving into the fundamental principles. Preparation oF Coal It is usually necessary to crush the mine-run coal before sending it to the jigs, the degree of crushing depending on the occurrence of the sulfur and other impurities in the coal and the type of jig over which it is to be sent. The feldspar jig requires finer and more uniform crushing

Jan 1, 1920

By Paul D. Merica, R. G. Waltenberg

Although nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the nomenclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Berns-dorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By E. S. Wheeler, M. W. Murphy

A LARGE part of the molybdenum produced in Colorado is converted and consumed in the Eastern States. As the raw materials and the power needed for the conversion of the Colorado concentrate are also accessible in the Eastern States, the conversion plant has been installed some 1500 miles east of where the ore is mined and milled. When concentrate was first produced at Climax in 1918, a custom smelter converted the product into ferromolybdenum. By 1924, the Company had decided to produce calcium molybdate and rented a building and installed equipment for that purpose at Langeloth, near Burgettstown, Pa., about thirty miles west of Pittsburgh. For the first few years the plant was a simple one of small capacity. A small hand-rabbled roaster was used, the product of which was made iota calcium molybdate by a conventional method; then an eight hearth mechanically rabbled roaster was installed to increase and speed up production. The output was considerably less than a million pounds of contained molybdenum annually until 1928, when a small part of the produc-

Jan 1, 1946

By Eugene A. Mizikar

A mathetnatical model of heal transfer in continuously cast steel slabs is described. The model, consisting of a unidimensional transient conduction equation and boundary condition equations, has been pvogrammed for computer solution. Temperatuve and solidification profiles calculated for a 6-in. slab, being cast under several conditions of secondary cooling, are presented and compared. Calculated solidification profiles are in agreement with reported expevinle~ztal values. For the mold zone, the predicted slab shell thickness can be described by: Resuilts of the study indicate that multibank spray cooling followed by radiant cooling should be employed when solidifying thick slabs with minimum surface temperature of 1600°F. Under these conditions, a 6-in. slab can be expected to solidify in about 8.3 min. Computer results also indicate that radiant cooling can replace spray cooling during solidification of the final 30 pct of slab with little increase in overall solidification time. CONTINUOUS casting has come to the forefront of the steel industry in recent years because of economic advantages resulting from increased yields and elimination of several processing steps. Considerable work, however, remains to be done regarding modifications to the process and operating procedures. Both a lack of operating plants in this country and the experimental difficulties associated with direct measurements on moving castings have made determination of solidification rates and temperature distributions difficult. An alternate approach is to mathematically simulate heat transfer in a continuously cast section, and then calculate the temperature distributions as a function of the controllable variables of the process. Simulation of heat transfer during solidification requires that a nonlinear mathematical problem be solved. As pointed out by Ruddle,' there are two mathematical approaches to the problem- the analytical approach and the numerical approach. While the analytical approach is certainly the more elegant of the two, it does require a number of inexact assumptions because of the complexity of the problem. For example, noteworthy analytical treatments of heat transfer in continuous casting have been developed by Savage Hills,3 and pehlke4 only by making one or more simplifying assumptions such as invariant thermophysical properties, constant heat-transfer coefficients in the mold, and linear temperature profiles in the shell. Simplifying assumptions such as these can introduce considerable uncertainty in the validity of results calculated with analytical solutions. Numerical solutions, which are considerably more versatile, appear to be better suited for solving solidification problems. Complex variations in the boundary conditions and variable thermophysical properties can be handled readily with this technique. Whereas numerical computations can be long and tedious when done by hand, results can now be obtained quite rapidly with the use of either the digital or analog computer. Several numerical models of heat transfer in continuous casting have been published. In 1963, Adenis, Coats, and Ragones published a numerical model used to calculate temperature distributions in direct-chill-cast magnesium billets. More recently, Donaldson and Hess 6 presented results obtained with a numerical computer model of heat transfer in continuously cast steel billets. In the present study, a model of unidimensional heat transfer in continuously cast slabs is presented. The method of solution on a digital computer is also included. Calculated temperature distributions and solidification profiles for various schemes of secondary cooling along with attempts to verify the model are also discussed. MATHEMATICAL MODEL The schematic representation of the slab continuous casting process in Fig. 1 illustrates that the slab passes through three distinct zones of cooling. Accordingly, the mathematical model consists of three parts: 1) solidification in the mold; 2) solidification in the spray cooling zone ; 3) solidification in the radiant cooling zone. Heat-Transfer Equations. The model was developed bymaking a heat balance on a horizontal slice of slab over the time period required for the slice to proceed from the liquid metal meniscus in the mold to the cutoff station. As shown in Fig. 2, the imaginary slice extends from the center line to the surface of the slab. As the slice moves downward, heat is conducted from the center line to the surface of the slab at a rate governed by the surface boundary condition and thermophysical properties of the metal in the slice. The following partial differential equation describes the conduction of heat in a medium moving at velocity U in direction Z:

Jan 1, 1968

By A. R. Gregory, A. L. Podio, K. E. Gray

Dynamic elastic properties of dry and water-saturated Green River shale samples were computed from compressional- and shear-wave velocity measurements. P- and 5-wave velocity measurements were made in three mutually perpendicular directions with respect to the bedding planes. Measurements were also made in several different directions by varying the angle between the bedding planes and the direction of propagation of the wave for angles of 0, 30, 45, 60 and 909 The oriented samples were subjected to both confining pressure and axial loads, in excess of the confining stress, in the direction of propagation. In general, P- and S-wave velocities increased with increasing stress levels, with a corresponding increase in Young's modulus. Water saturation caused the P-wave velocity to increase and the S-wave velocity to decrease. Elastic moduli decreased upon saturation, except for Pois son's ratio, which increased, indicating some degree of weakening of the material. The samples showed a moderate degree of anisotropy; this was to be expected from the laminated nature and shallow occurrence of Green River shale. INTRODUCTION This paper presents some results of an experimental determination of the elastic coefficients of anisotropic materials (in particular, finely layered rocks and minerals such as Green River shale) from measurements of dilatational and shear-ultrasonic-wave velocities. Ultrasonic techniques have been used extensively in nondestructive testing. Several methods have been proposed by Mcskimmin, 1 and some of these have been used successfully to measure ultrasonic velocities in rocks. Hughes and Cross, 2 Wyllie et al., 3 and Birch 4,5 developed pulse first-arrival techniques for the measurement of dilatational and shear velocities. Williams and Lamb 6 used the method of cancellation of a traveling wave, which was later modified by Myers et al.' and perfected by McSkimmin. 8 Although this method is highly accurate, it has not been used as widely as the pulse-transmission methods recently reported by Jamieson and Hoskins 9 King,10 and Mattaboni and Schreiber. 11 It has been common practice to use some form of crystal transducers, either quartz or ceramic, that has been cut or polarized in different directions in order to generate either compressional or shear waves. However, accurate determination of shear wave velocities has been difficult due to problems that arise in obtaining a pure shear wave from cross-polarized crystals, which usually also generate a small amount of compressional energy. As reported by Gregory, 12 this energy can be seen as a long precursor preceding the sharp break of the shear first arrival. The need for generating pure shear waves led to interest in mode-conversion techniques, which are based upon conversion of the mode of vibration through wave reflection or refraction at a discontinuity. Arenberg13 showed that for certain materials and for certain angles of incidence it is possible to generate pure shear modes by reflection at a boundary. Jamieson and Hoskins 9 used a pyrex glass-air interface for generating pure shear waves, and King 10 used this method successfully for measuring shear-wave velocities in rocks. Gregory l4 arrived at a similar result by refraction of a wave at an aluminum-oil interface. A plane compressional wave, traveling in the oil phase, is incident on the aluminum at an angle larger than the critical angle for compressional waves, and thereby generates a purely transverse, plane-polarized wave in the aluminum. During the last few years methods have been developed that allow the simultaneous determination of shear and compressional velocities in solids.

Jan 1, 1969

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By W. Hurst

What is entailed here is the extension of the sinzplified material balance formulas to encompass interference between oil fields. As previously reported, the ex-plicitness as so revealed for the cunzulative pressure drop as a function of all factors contributing to its change in the material balance equation, is now transcribed through the inter-conzmunicating aquifer to effect an increased pressure drop on an adjoining field by interference. Such is performed by mathematical analyses and the application of the Laplace transformations. What is accomplished is that the reiteration problems previously associated with interference studies are nullified, since volumetric changes for the fluids in situ are automatically adjusted by the explicitness so expressed, and what pertains to the superposition principle applies only to the impeded water drive upon a su.bject field, which is likewise incorporated in the over-all pressure drop that results. The mathematics treats with the rigorous solution of the problem, as well as with methods easily amenable to numerical interpretation by the practicing engineer. In all cases, however, what is deduced for areal extents, reveal interference between wells when time becomes large that further substantiate the analyses. Probably of equal significance, all variables and for/nation characteristics are accounted for. This applies to the differences in PVT analyses that occur from field to field and the physical parameters associated with the lithology of the reservoirs. The latter is deduced from a rigorous interpretation of the unsteady-state flow problem for sands of different permeabilities in series. Thus, what purports to be a trial-and-error calculation to include variations in sand conditions within the intercommunicating aquifer to define water drive has little importance compared to the designation of such paranzeters at the reservoir to constitute the essential criteria. INTRODUCTION In a recent publication, the reader has been introduced to the simplified material balance formulas,' It has been shown that the complexities formerly associated for identifying and determining reservoir pressure in the material balance relationship can be resolved by treating with the Laplace transformations, the inversion of which reveals pressure as an explicit function of all factors contributing to its change. For an under saturated oil reservoir, this constitutes an integrated effect from the inception of production; and for a saturated oil reservoir, such represents a survey traverse. However, what is most important, for the first time we are able to express the pressure change in a reservoir directly to the oil, gas and water produced, and to the physical parameters of the formation, in the same manner that reservoir pressure has served in the past to define well interference — which opens up this avenue of endeavor for investigating interference between oil fields. The occurrence of interference is by virtue of the juxtaposition of two or more oil reservoirs producing in the same aquifer. Thus, in any one field, the extended production so incurred creates a pressure lowering in the field, as well as in the aquifer, which can now be transcribed by these simplified material balance formulas to the adjoining reservoir to observe the increased pressure change so induced. These effects are retroactive from field to field, to reveal a pressure drop far in excess of normal depletion to evidence the interference pattern that can result. Such is the purpose for the present undertaking — to develop the mathematical physics treating with this phenomenon of interference between oil fields, employing the simplified material balance formulas. Since Ref. 1 often will be referred to in the text, it is identified as "The Simplification", in the same connotation that another paper has been referred to as the "Laplace Trans-formation. However, the amount of material to be covered in these passages is substantial; therefore, the total emphasis will be placed upon developing these fundamental ideas treating with interference rather than attempting to offer work curves, which always can be prepared. For the practical application of these simplified material balance formulas that form the framework of the present development, the reader will find a comprehensive treatment in the Appendix of Ref. 1, illustrating a factual field example. In essence, what is proposed by this presentation is to make available to the practicing engineer a simplified means to treat with interference between oil fields, independent of the complex machine computations that have attended such undertakings in the past. As the problem unfolds, a common pattern will be discernible, whereby the many reiteration processes that previously required computing devices are eliminated.

By George C. Branner

STATE geological surveys have had an interesting development in this country. They first appeared more than a hundred years ago. The fact that they have persisted and are now an important part of most state governments indicates the basic need for state departments con-cerned with mineral problems. The number of state surveys in 1941 (43) is at an all-time high, as is the aggre¬gate appropriation for their support for the fiscal year 1940-'41 ($1,600,708). The first surveys, those of North and South Carolina (see Fig. 1), made their appearance in 1820-'30, but neither survived that period. During the next two decades surveys were created in twenty states, but only three survived. In fact, it was not until the decade 1900-'10, when eighteen surveys were created and only five abolished, that these agencies became firmly established.

Jan 1, 1941