Search Documents

By Hongwei Zhang, Sen Yang, Shimin Liu

"This laboratory study investigates the damage evolution of sandstone specimens under two types of cyclic loading conditions through monitoring and analyzing the variations of elastic moduli and ultrasonic velocities. We adopted the rigidity degradation method for evaluating the damage accumulation through the rock dynamic ultrasonic velocity measurements. Compared to the ultrasonic test, the method of rigidity degradation shows deficiencies in the detection of damage development. The cyclic loading within the elastic limit led to a stiffening trend for the loading process but a softening trend for unloading process. The method of rigidity degradation was unable to describe the damage accumulation in this situation, while P-wave velocity clearly reflected the damage development. Moreover, a simplified model is established for interpreting the behaviors of the modulus variations and ultrasonic velocity. The cyclic loading within elastic limit enhances the anisotropy of rock, which causes a denser packing pattern in the direction of axial stress. The persistent damage accumulation under the cycling with an increasing upper limit is the consequence of the tensile failure in the microstructure of sandstone. INTRODUCTION The damage accumulation due to dynamic (cyclic) loading is highly detrimental in many engineering structures, such as mine openings, petroleum and natural gas boreholes, tunnels, rock foundations, and underground chambers. The sources of cyclic or repetitive loadings can be roughly divided into two types: (1) periodic operation, including drilling, blasting, and mining; (2) random vibration, including earthquakes and traffic loads. The repetitive loading-unloading process opens and closes the micro-pores and micro-cracks within the rock, further inducing the growth of cracks. As expected, the accumulating damage becomes a potential factor to trigger the rapid and violent failures of large-scale engineering rock structure."

Jan 1, 2017

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By Takashi Sasaoka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 million tons of lignite annually from open-cut mining. The coal is used to generate 2,400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400? 500 m (1,312?1,640 ft) deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m (82 ft) thick with 20?25 m (66?82 ft) of interburden between them. Up to now, many mining systems for thick coal seams have been used and improved in the world. However, where the thickness of coal seams is beyond the limitation of the current mining technology and system, an applicable mining system has to be introduced, considering influencing factors such as caving and subsidence. In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early2009. This paper describes underground mining systems for thick coal seams and proposes an innovative underground mining system for thick coal seam, ?eco-friendly underground mining system?, considering geological, geotechnical, and environmental conditions in this mine. This paper discusses its applicability to this mine by means of numerical analysis from the geotechnical point of view.

Jan 1, 2011

By Christopher Mark

The past decade has provided a wealth of practical experience with longwall pillar design. Design formulas developed specifically for longwalls have proven their value in numerous applications. Analytic methods, including numerical models, have a1 so made important contributions. These advances have been based on basic research into abutment loads, coal pillar mechanics, and the interaction between pillar performance and entry stability. The goal of this paper is to review the state of the art in longwall pillar design from the standpoint of the practitioner. Actual case histories are presented to illustrate the current capabilities and limitations of pillar design methods. The paper also discusses the advances that can be expected in the future.

Jan 1, 1990

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By Thomas M. Barczak

The performance characteristics of Mobile Roof Supports (MRS's) were evaluated through full-scale testing in the Strategic Structures Testing Laboratory at the National Institute for Occupational Safety and Health, Pittsburgh Research Center. Safety issues pertaining to the operation and design of these supports for pillar extraction during retreat mining are examined. A unique load frame, called the mine roof simulator, provided a realistic simulation of mining conditions by inducing vertical, horizontal, and lateral loading on the support. The purpose of these experiments was to determine the capabilities and limitations of the supports and to investigate factors that influence the measurement of loading and loading rate. An evaluation of the support design and load conditions that can cause support failure or loss of support capacity are discussed relative to the laboratory tests. In general, lateral loading perpendicular to the longitudinal axis of the canopy is most severe, although horizontal loading in the direction of the long axis of the canopy can also produce critical loading in some cases. The experiments indicate that both setting force and leg pressure measurements are influenced by the staging of the leg cylinders. The implications of these factors on load rate measurement are evaluated. A comparison of MRS capacity and stiffness characteristics is made to conventional timber supports.

Jan 1, 1997

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

By Brent A. Slaker, Michael Murphy, John Ellenberger, Erik Westman

"Photogrammetry, as a tool for monitoring underground mine deformation, is an alternative to traditional point measurement devices, and may be capable of accurate measurements in situations where technologies such as laser scanning are unsuited, undesired or cost-prohibitive. An underground limestone mine in Ohio is used as a test case for monitoring of structurally unstable pillars. Seven pillars were photographed during four visits over a 63- day period. Using photogrammetry, point clouds of the mine geometry were obtained and triangulated surfaces were generated to determine volumes of change over time. Pillar spalling in the range of 0.29–4.03 m3 of rock on individual rib faces was detected. Isolated incidents of rock expansion prior to failure, and the isolated failure of a weak shale band, were also observed. Much of the pillars remained unchanged during the monitoring period, which is indicative of proper alignment in the triangulated surfaces. The photographs of some ribs were of either too poor quality or had insufficient overlap, and were not included. However, photogrammetry was successfully applied to multiple ribs in quantifying the pillar geometry change over time.IntroductionAdequately measuring underground rock mass movements is integral to understanding how rock masses behave and how to interact with them safely and efficiently. Many modern measurement techniques employed in underground mining environments rely on point measurements, such as through extensometers or borehole relief methods (Christiansson, 2006). These techniques, while commonplace, do not provide a comprehensive view of how the rock mass is behaving. The dynamic changes in stress states underground, coupled with the mechanical uncertainty of rock masses, near active excavations, creates a need for measurement systems which better capture the behavior of the rock mass. Photogrammetry is a technology capable of producing the wide-area displacement measurements required for a comprehensive understanding of rock mass movements.Digital photogrammetry is a means of obtaining threedimensional point clouds from digital photographs. By finding the same point across multiple images, all viewing an object from different angles, the location of that point in three-dimensional space can be inferred. Close range digital photogrammetry (CRDP) is photogrammetry applied to measuring objects or scenes less than 100 meters away (Atkinson, 1996), and is used for various functions in underground mining environments. These uses include, but are not limited to, mapping fracture networks (Kim, Kim, & Won, 2005)(Somervuori & Lamberg, 2010), characterizing fractures (Styles et al., 2010) and measuring volumes of blast rock (Heal, Hudyma, & Potvin, 2004)."

Jan 1, 2015

By Jonathan P. Furniss

The paper describes a range of laboratory tests undertaken on full column resin anchored glass fibre rockbolt systems, to assess all aspects of their performance. Laboratory instrumentation has been developed for the accurate study of strain transferral from the Glass Fibre Reinforced Plastic (GRF') bolt, through the surrounding resin annulus, and into the rock. Experience in laboratory testing to the new British Standard on glass fibre rockbolting is discussed. A critical comparison is made of the influencing parameters affecting . underground rockbolted roadway performance to the parameters assessed by BS 7861 : Part 1 The work has been co-funded by MA1 Systems UK Ltd. who supply GRP rockbolt components to the British coal mining industry, mainly for the reinforcement of coal ribsides. In rockbolting, glass fibre has a number of useful * qualities which are discussed in the paper. These properties, make the product more suitable than steel in certain applications, both in mines, and other engineering structures such as tunnels, soil stabilisation, and coastal defences.

Jan 1, 1997

By Anton Sroka

The German hard coal production predominantly derives from underground multiseam mining activities. Beside common surface damages, ?inner mine damages? on underground infrastructures (i.e. main roads, cross cuts and shafts) due to mining excavations occur to an increasing extent. As these "inner mine damages" dramatically increased because of the development towards high performance longwall mining technologies, this matter raised to be a severe problem concerning mining economics. To protect durable and long lasting underground infrastructures, precautionary measures such as suitable mine layouts, adapted planning of mining operations and moderate face advances have to be considered. Some examples of "inner mine damages" recorded by means of mine surveying methods are given in this paper. An empirical-mathematical model based on the principles of mining subsidence engineering methods will be introduced. This model allows to minimize ?inner mine damages? and helps to support and optimize mining processes.

Jan 1, 1999

By Deno M. Pappas

The purpose of this U.S. Bureau of Mines study was to determine the material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were used to approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted on simulated gob material from 3 different rock types. The study found that the nonlinear stress-strain curves obtained from the three materials were similar, and could be represented in terms of moduli as follows: Es = 2.36s + 1,360 (1) Et = 0.00181s2 + 9.33s + 294 (2) where Es = secant modulus, psi Et = tangent modulus, psi and, s = stress level (due to overburden), psi. These curves correlated well with the theoretical solution curves developed by Salamon. Other effects on gob behavior were attributable to these studied factors including void ratio, thickness-to-width shape ratio, and rock compressive strength. The generated equations should provide numerical modelers with a practical means of estimating gob modulus as a function of stress level.

Jan 1, 1993

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988