Search Documents

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By Frank F. Aplan

Introduction Gravity concentration may be defined as that process where particles of mixed sizes, shapes, and specific gravities are separated from each other by the force of gravity or by centrifugal force. The nature of the process is such that size and shape classification are an inherent part of the process in addition to separation on the basis of specific gravity from whence the process got its name. Mother nature has long practiced this form of mineral concentration by concentrating such heavy and relatively indestructible minerals as gold, platinum, cassiterite, ilmenite, zircon, and diamonds in placer or beach sand deposits. Once freed of their host granitic or other rock through natural weathering processes, these minerals are then subjected to stream or wave action producing a natural classification and concentration of the heavy minerals. Gravity concentration dates back to antiquity and was certainly the first ore concentration process used when selective mining and hand sorting would no longer suffice to produce the quality of concentrate desired. Forerunners of the present day sluice box and panning techniques were undoubtedly used by the ancient Egyptians on the upper Nile to separate gold from stream gravel. By the second century BC the extraction of gold from veins in quartz was well detailed by Agatharchides, but there is evidence that gold was brought into Egypt from the south as early as the XI1 Dynasty (~1900 BC).1 Most assuredly gravity concentration devices were used during the later Bronze Age to separate the heavier tin and copper minerals from their lighter gangue minerals. The Athenians used an elementary form of Rowing film concentration at their lead-silver mines at Laurium,2 and elementary jigging using wicker baskets was also probably developed at this time. Agricola's famous treatise De Re Metallica3 demonstrates that by the 16th century gravity concentration technology was well advanced and a large number of devices had been developed. Chinese

Jan 1, 1985

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the conventional petroleum production cycle in then-known fields within th’e U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oilor bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67070of the 00IP will remain in place at the end of the

Jan 1, 1980

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the con¬ventional petroleum production cycle in then-known fields within the U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oil-or bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67% of the OOIP will remain in place at the end of the

Jan 9, 1980

By John S. Egbert

Many of you are familiar with the Washington Metro Project. However, inasmuch as some may not be, and others may want to refresh their memories regarding certain facets of the project, I will cite a few summary details about the rail transit system we are constructing. That summary will also give each of us a common point for departure as I develop the principal thoughts that I want to leave with you. The Washington Metropolitan Area Transit Authority (WMATA) is an interstate agency established by Compact between the District of Columbia, Maryland and Virginia and approved by the United States Congress. Currently, the Authority has approval to build and operate a 101-mile (162.5 km) regional rapid rail transit system as shown on Appendix A. Of that total, 38 miles (61.2 km) will be in D. C., 32 miles (51.5 km) in Maryland and 30 miles (48.3 km) in Virginia. (Mileage figures, because of rounding error, do not add to 101 miles.) Referring again to the 101-mile total, 48 miles (77.2 km) will be underground, 42 miles (67.6 km) on the surface and 10 miles (16.1 km) on aerial structures. Of the 48 miles (77.2 km) that are underground, 15 miles (24.1 km) are rock tunnel, 14 miles (22.5 km) are earth tunnel, 0.5 miles (0.8 km) 9.s sunken tube and 19 miles (30.6 inn) are cut-and-cover construction. The system will include 86 stations, with 51 of them underground. Referring again to the full 86 stations, 43 will be in D. C., 23 in Maryland and 20 in Virginia. We currently have 37 miles (59.5 km) of line and 41 stations in operations as shown on Appendix B. Also shown on Appendix B is another 16 mile (25.7 km) increment and 13 stations which have been substantially completed, but are not yet in service. Additionally,

Jan 1, 1981

By M. T. Long

The Crestmore Limestone Mine of Riverside Cement Company in Riverside, California is situated within 1.6 km of the Santa Ana River. It is an alluvium covered deposit with a massive quartz manzonite intrustion separating the upper and lower limestone beds which dip from 30° to 50°. The highly fractured upper bed contacting the Santa Ana alluvium contains many unique water inflow problems which vary, from multiple high pressure 19 liters per minute inflows up to 3,000 liters per minute to 11,000 liters per minute inflows-contacted by development mining in April 1983. A case history of the successful grouting of these inflows and the continual grouting procedures in advance of present mining with empirical' results are discussed.

Jan 1, 1984

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By Douglas J. Cork

Biohydrometallurgica1 processes in the areas of coal desulfurization (Hoffman, M.R., et al., 1981) and recovery of metals from metal sulfide ores (Lundgren, D.G. and Malouf E.E., 1983) are well known. In addition other areas of potential interest to the mining industries have been outlined (Spisak, J.F., 1979). For instance, scientists involved in this interdisciplinary field have endeavored to apply microorganisms to the problem of effluent sulfate disposal. This chapter assesses the feasibility of utilizing a particular two stage anaerobic microbial process to convert effluent sulfate to orthorhombic sulfur. Strong emphasis is given to the possibility of substituting this bioprocess for alternative gypsum synthesis and disposal methodologies commonly practiced by companies which emphasize sulfuric acid or ammonium sulfate leaching processes.

Jan 1, 1985

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By John C. Brower

Bolivia is nor a major gold producer but has produced continuously since pre Inca times. Production reached a peak in 1964 of about 4,000,000 grams and is currently about 1,000,000 grams. Production is mainly from the Tipuani River valley north of La Paz and is derived from Pleistocene basin fill: the Cangalli conglomerate and overlying terraces. Abandoned Pleistocene lake terraces south of La Paz in the Oruro area are another source of gold whose potential have not been realized. In both the Tipuani and Oruro areas, primitive hand methods are the principal means of production, with the exception of a single modern dredge. In spite of a long history of production, probably very little of the gold potential has been mined.

Jan 1, 1979

By Rob Robertson

The problem of fine coal slimes has been addressed in a unique way at A. T. Massey Coal?Company. Several plants have employed two-stage classifying cyclones to separate the minus 1 mm raw coal into 3 sizes. Larger cyclones make the initial cut at approximately 150 µ (100?mesh) sending the underflow to a cleaning circuit (usually spirals) while the overflow is pumped to a secondary cyclone circuit using smaller cyclones. The small cyclones make a cut at near 70 µ (200 mesh) and produce an underflow that is a des limed flotation feed. The overflow is discarded to refuse due to its high ash and superfine size which would produce a high moisture product even if suitably recovered.

Jan 1, 1998

By Charles N. Alpers, D. Kirk Nordstorm

A variety of approaches have been used in the recent literature for the estimation of pre-mining (or natural background) metal concentrations in areas affected by mining. The following is a list of some of these approaches: (1) historical and anecdotal data, (2) remote analogues (other similarly mineralized areas), (3) proximal analogues (nearby mineralized areas), (4) sediment sampling (streambeds, lakes, estuaries, floodplain deposits, and soil profiles), (5) stable isotopes (hydrogen, oxygen, sulfur, and carbon), (6) geochemical modeling (forward, equilibrium-based), (7) geochemical modeling (forward, kinetic- and transport-based, and inverse), (8) statistical analyses, (9) mass balance on oxygen flux, (10) mass balance with age determination of weathered material. Examples of each approach are described, and the strengths and limitations of each approach are discussed.

Jan 1, 2000

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By Courtney Black, Paul F. Ziemkiewicz, Eberhard Werner, Matthew Daly, Joseph J. Donovan, Jeff Frazier

Injection of alkaline waste-lime slurry was performed at a West Virginia surface coal mine site, to attempt neutralization of acid springs by an alkaline recharge method. Deep trenching (>5 m) using an excavator yielded the most effective injection into the aquifer. Water from two springs, 90 m from the deep trench, showed 70%-80% reduction in acidity in response to injection. Neutralization persisted >170 days after treatment, with pH between 5.1-5.7 and metal acidity from 25-60 mg/L. A minor fraction of lime introduced was consumed. The sustained neutralization is attributed to reaction of acid water with subsurface lime, entrained below the wafer table by macropore infiltration. Characteristics of groundwater transport are critical in determining recharge structure location.

Jan 1, 2000

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023