Search Documents

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By Q. Feng

"Efforts have been tried to apply the mixture of mine tailings and fly ash as construction materials. Through the present investigation, a protocol to make construction materials using the mixture of mine tailings and fly ash has been set up. The experiment results of the present work also help set up the working conditions such as activation temperature and time, the concentration of NaOH, the addition of Ca(OH)2, forming pressure, mine tailing to fly ash weight ratio, curing temperature and curing time. The findings of the present work provide a novel method for the geopolymerization of the mixture of mine tailings and fly ash as construction materials, such as bricks for construction and road pavement. INTRODUCTION In mining activity, after the valuable materials are extracted from ores, millions of tons of solid rejects, i.e., mine tailings, are stored in the tailings dam, which occupies a huge area of land and leads to high monetary, environmental and ecological costs. For example, the impoundment of mine tailings can bring with serious environmental problems such as mine dust and tailing dam failure. On the other hand, the making of general construction material results in a lot of greenhouse gas emission. Therefore, it is of great interest to utilize mine tailings, for which a lot of energy has been consumed during the comminution process, as construction materials using the novel geopolymerization technique. (Xu and van Deventer, 2000, 2002a, 2002b; Pacheco-Torgal et al., 2007, 2008; Zhang et al., 2011; Ahmari et al., 2012) Fly ash is another industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials because it is a silica/alumina rich aluminosilicate source. In addition, the facts that fly ash is quite reactive to alkali and its particle size is usually very small (< 50 microns) make the specific material an ideal source for the geopolymerization process to make construction materials. Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution at an elevated temperature. After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as mine tailings and fly ash as construction materials."

Jan 1, 2016

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By A. Moergeli, Philip Sander, John J. Reilly

"Estimating and managing the costs of complex infrastructure projects – in the planning/design and construction phases, for both owners and contractors – has been a challenge for decades. The more complex and technologically advanced the project, the greater the uncertainty, including potential risks that are important to owners and contractors, such as:• Cost risks to owners – meeting budget and schedule, maintaining public credibility.• Cost risks to contractors – profit, consequences of loss, impacts to reputation/future work.This concern has been addressed in various ways by the underground construction industry for some time (Reilly, 2001). In particular, while significant advances have been made in cost estimating for the planning and design phases (Reilly et al., 2004), that are important to agencies and political decision-makers, it is not apparent that these advances have been widely adopted for construction cost estimates. The reasons for this may relate to lowbid considerations – any method that tends to increase the contractor’s cost estimate, by including risk or likely costs, could lead to an erosion of the contractor’s competitive position – if others are not similarly required to include such costs.Different cost estimating methods produce different levels of information. Specifically, there is a large difference in the character and depth of information if a deterministic (quantities times price plus a contingency) and risk-based cost methods are used. It is this difference in character and depth of information that is the reason that risk-based cost estimating has potential value for owners and contractors. Figure 1 presents hypothetical cost results from deterministic and risk-based methods and illustrates some of these differences.In Fig. 1, the results for deterministic and risk-based cost estimates are given related to the potential profit or loss for a typical project. As is evident in this example, there is significant potential for costs to be realized that are higher than the proposal/bid value estimated using a deterministic approach, with a 15 percent probability of a loss. There is a 30 percent probability that the project will have a reduced profit. There is a 55 percent probability that the project will return a good profit. Using a risk-based approach, it is possible to better recognize this potential outcome in the bid phase and, as a consequence, develop a strategy to:"

Apr 1, 2016

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its&apos; cashflow position from negative to positive within two years.

Jan 1, 1991

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller&apos;s logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By J. J. Gusek

An 81 hectare (200 acre) tailings impoundment at a taconite operation in Wyoming that ceased operations in 1983 has been a source of blowing dust. The site qualified for reclamation under Wyoming&apos;s Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction included: incorporating commercially available organic amendments and fertilizers into a 300 mm (12 in) thick "cap" of a sterile clay loam cover material, lowering the water level in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin, constructing a wide tailings pond spillway that allows flood control while minimizing seasonal water level fluctuations in the pond, and building rock berms and rock snow fences for wind erosion control and soil moisture preservation. Tree planting in the protective wind/snow shadows of rock berms and rock snow fences, and the plugging of a decant pipe are planned for future work.

Jan 1, 1998

By Allan M. Johnson

The Sherwood Mine is being monitored to determine the nature and extent of changes in the mine and its environs which result from the closing and the cessation of pumping. Of particular interest was the possibility of piping-induced subsidence occurring as the mine flooded. Previous experience in the district indicated that this possibility was very real. A monitoring system, including acoustic sensors, extensometers, surface subsidence monuments, and ground water observation wells was installed in July 1978, just prior to the mine closing. Late in 1979, three piping-induced subsidence events occurred. The monitored data, and related laboratory studies are being applied to a quantitative description of piping-induced subsidence.

Jan 1, 1980

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972