Search Documents

By N. I. Um

The coal bottom ash generated from coal-fired power plant accounted for approximately 5 mil-lion tons in Korea. Almost all of coal bottom ash was treated as reclamation of the landfill because of the content of unburned carbon. For recycling of coal bottom ash, effective removal of that is required. So, in this study, the removal of unburned carbon by flotation was studied with respect to adsorption ability in surface of a bubble in order to consider its application to recycle the coal bottom ash. The sample A, B and C were that the coal bottom ash contained 2.73%, 7.01% and 10.49% of the unburned carbon (UC) respectively. The column flotation was carried out for each time as the artificial injection of air at 10.0L/min flow rate and the reagents of 500g/ton kerosene and 80g/ton MIBC were used. The samples per water of 1.3 liters were from 0.5% to 4% (w/w.%). In the result of this study, the kinetic curves of unburned carbon adsorption from injected air bubbles were in-creased rapidly as equilibrium was approached; only 5 sec was needed from the sample A and B and 10 sec was from sample C. And the equilibrium isotherms of unburned carbon adsorbed by the infected air bubble from the sample B and C could appear the BET adsorption isotherm; MT = KMEEO/(EO-E)[EO+(K-1)E](K: adsorption affinity), but not the sample A that was not enough to express the adsorption curve.

Jan 1, 2014

By Danilo Zim, Matheus Paschoalino, Denis Guimarães, Jasbir Gill

The shortage of water supply in some regions of the globe is particularly problematic and forces mining companies to adopt alternatives like pumping sea water from the ocean up to the mining sites. Although deaeration of sea water or the use of lined pipelines are known options to prevent corrosion during pumping, a recent development of a new corrosion inhibitor allowed the use of simple mild steel pipelines for this purpose. The objective of this study is to demonstrate the recent advances of this technology in protecting against not only general corrosion but localized corrosion, main cause of corrosion-related pipeline failures. Corrosion studies were carried out using electrochemical techniques, weight loss balance as well microscopy surface analysis in order to measure and therefore evaluate the treatment efficiency. The right dosage of corrosion inhibitors may vary depending on water composition and characteristics of each system. Differences were observed depending on the sea water source. Pretreatment of metallic surface impacts the observed corrosion rate which can be as low as 3.6 mpy. The absence of pitting or localized corrosion was achieved in aerated seawater.

Jan 1, 2014

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By Yonghui Hu, Hongxiang Ran, Honggang Wei

"A new PVM vertical ring high-gradient high-intensity permanent magnetic separator authorized by China Invention Patent ZL201110294866.4, which featured with vertical magnetic field structure was developed to dramatically save energy consumption and running costs compared with electromagnetic separators. The specific magnetic circuit design ensures PVM separator generating high magnetic field intensity as well as solving equipment large-scaling. The newly developed industrial PVM separator has been proved suitable for recovery of weak magnetic minerals or purification of non-metallic minerals benefiting from its high background and induction magnetic field intensity up to 0.8/1.5T, stable service performance and low running costs. The first ?1.5mm PVM separator has been applied in removing iron from quartz sand in Fengyang, Anhui, and ?2mm PVM separator will be installed to separate hematite. Industrial applications and tests proved that PVM separators could gain similar separation effects and especially save more than 80% of power consumption compared with the conventional electromagnetic high-gradient high-intensity magnetic separator, which will contribute a lot for energy conservation and environmental protection. The development of high gradient magnetic separator technology has played an important role in utilizing weak magnetic minerals, which has been widely used in many mining enterprises. The main forms of high-gradient magnetic separators include both of electromagnetic high-gradient and permanent magnetic high-gradient. The vertical ring high-gradient high-intensity permanent magnetic separator features with high magnetic field gradient, large processing capacity and never clogging, which has been widely used in recovering fine weak magnetic mineral and purification of non-metallic minerals[1-3]. However, electromagnetic coils excitation needs more energy consumption, and relatively high running costs and maintenance costs as a result of the complicated cooling system. So permanent magnetization of the electromagnetic magnetic separation equipment is a very important research direction at present. With the continuous improvement of resource utilization standard and efficiency requirements, high energy consumption of the electromagnetic vertical ring magnetic separator have been highlighted, which has affected the economic benefits of mining enterprises to a certain extent. In the aspect of high-gradient high-intensity permanent magnetic separation equipment, considerable researches have been carried out at home and abroad and many small-sized prototypes were developed yet never strode into large-scale industry applications[4-6]."

Jan 1, 2018

By R. Paturi

Mill liners play an important role in the operation of a mineral concentrator influencing the throughput, availability, power drawn and the efficiency of the mill in the plant. Liners protect the shell and transfer energy to the grinding charge. Metso Technology Development has conceptualized, developed and successfully implemented physics based 3D DEM simulation techniques to predict charge motion, power drawn, energy spectra and wear over the life of the liner. This paper will present a case study of shell liner optimization for a 34? SAG mill including the input data requirements, and shell liner optimization methodology using the 3D simulations that eliminates the need for the traditional expensive and lengthy proto-type testing. These simulations will cover ball and particle movement, liner wear and mill power draw, and do not cover particle breakage and slurry flow. Even the liner manufacturers lack the ability to provide this type of qualitative and quantitative information on their products. The data from these simulations provides the plant engineers a scientific basis for their decision making and thus eliminates guess work. Keywords: liner, optimization, multi-physics, 3D-DEM

Sep 1, 2012

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By Swati Mohanty

Spiral concentrator, which works on the principle of gravity separation, is widely used in the mineral industries for separation of solid particles based on the size and density. In the present study, CFD simulation of the flow profile on a laboratory scale spiral concentrator of height 2.29 m, pitch 0.435 m and width 0.17m was carried out. A single computational domain covering the entire spiral was considered. Volume-of-Fluid algorithm was used to track the interface and predict the flow profile. In the present study the Donor-Acceptor method was used for the calculation of volume fraction in the cell. Simulation results show that the velocity increases as the water flows down due to the convective force and gravitational force, but the viscous force acting in the opposite direction retards the flow. Thus the maximum velocity is attained at turn three at which the viscous force overpowers the other forces and further down the velocity decreases. Measured water depths along the radius of the spiral at various heights were compared with simulated depths, which were in good agreement. The simulated liquid phase velocity profile was used to carry out preliminary studies on the flow profile of solid particles of size 500 micron and densities 2600kg/m3 and 5100kg/m3, based on the Lagrangian model taking into consideration fluid-particle interaction.

Sep 1, 2012

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By A. P. Das

Biomining technology focuses on achieving effective recovery of precious metals from their ores and concentrates using microbial techniques. Biomineral extraction of manganese from low-grade manganese ores using bioleaching was investigated in this paper. Five fungal strains were selected for screening of bioleaching of low-grade Mn ore collected from Sanindpur iron and manganese mines, Koira Sector, Keonjhar, Odisha, India. A fungal strain, Aspergillus niger was selected as it showed high efficiency of manganese leaching. Growth of the fungus was determined in terms of sbiomass dry weight and the final pH was monitored. The selected fungal strain was used for bioleaching of low-grade manganese ore of -150µm size particle size at 2 % pulp density with 2g/100ml sucrose concentration for duration of 20 days. About 60 % of Mn bioleaching was obtained with A. niger. The fungal species proved to be useful for manganese biomining.

Sep 1, 2012

By M. Vulkov

The paper is focused on the optimal selection of grinding medium for a drum mill. The decision-making is based on the fuzzy multiple attribute approach. One way to optimize the grinding process in a tumbling mill is associated with the development and testing a new shape of grinding body. Family of new grinding bodies ? spheroidal tetrahedrons (tetraballpebs) has been manufactured. Two types of spheroidal tetrahedrons and a classical ball (sphere) with one and the same weight are compared. A fuzzy entropy method to calculate the weight of the attributes is suggested. A grinding body which is the best approximation to the fuzzy formulated technological conditions is selected. Keywords: grinding, spheroidal tetrahedrons (tetraballpebs), balls, fuzzy sets

Sep 1, 2012

By Sergey Romanenko, Tatyana Aleksandrova, Karen Arustamian

"Current status of question about grinding stage effect to electrochemistry parameters of operation preparation slurry before intermediate selective flotation was assessed in the present scientific work. Needs of more detail study chemical reactions in the slurry preparation and flotation processes were shown. The ores are polymetallic sulphide type and the one are most difficult for mineral processing. The methodology allows increase information base during floatation tests. Ionometric methods and elements of neural network have been used in the study of mineral processing questions.We have also identified the relationship between the received values of the electrochemical parameters and the technological results in selective flotation. The optimal values of the electrochemistry parameters in operation of the preparation slurry before selective flotation has been found. The main effect of using the proposed methodology is to obtain scientifically based solutions to improve the technology parameters of flotation polymetallic sulfide ores. Challenging issue of selectivity of sulphide-polymetallic ores will be considered using case study of sulphidepolymetallic ores. It was shown that several factors are formed in ore grinding: formation of hydroxyl oxides of iron compounds, copper cation leaching, metal-sulphide and metal-sulphite complexes formation. The chemistry was revealed for current processes in slurry preparation operation before selective flotation. Quantitative assessment of interrelations between electrochemical parameters of slurry and process performance was given with using electrochemical control methods. Neuron network-based model was estimated based on data array and was allowed to establish optimum electrochemical conditions of metal-sulphite complex formation to provide maximum efficiency of selective flotation.INTRODUCTIONPhysical and chemical processes that take place in ore grinding have a significant impact on flotation selectivity and can cause low selectivity of the flotation process. Today this issue is given much attention. In the paper [1] it is pointed out that sulphide oxidation products and slurry components, such as sulphide ions, metallic iron and its oxidation products, have effect on flotation performance. So, metallic iron has impact on metal-sulphite complex formation as a result of oxidation-reduction reactions as follows:"

Jan 1, 2018

By R. L. Pascual, W. J. Whiten

"The froth flotation process is not well understood. Both flotation models, and the parameters used to describe the stream flows are not well defined. They in fact vary considerably in different applications. This creates difficulties is designing a simulation program suitable for use by plant personnel, consultants, and researchers. In addition to simulation, an effective simulation program can be expected to provide a range of other services.This paper shows how a process circuit simulator can be designed with sufficient flexibility to satisfy these needs, and discusses some of the additional services."

Jan 1, 2003

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By G. Granata, C. Tokoro, T. Kato

The rare earth elements (REE) are composed of 17 elements that are 15 elements of lanthanide added scandium and yttrium. REE are divided into light rare earth elements (LREE) and heavy rare earth elements (HREE). Although the supply source of LREE is distributed around the world, the supply sources are unevenly distributed. Thus, the development of a new HREE supply source is required. In this study, we focused on the weathered residual rare earth ore as a new HREE supply source. Since so far this weathered residual rare earth ore could not be treated neither by flotation nor by wet high intensity magnetic separation, it was not considered as HREE resource before. In this study, we investigated the leaching of HREE from the weathered residual rare earth ore and elucidated the effectiveness of planetary milling with sodium hydroxide as a method to enhance their recovery. For this purpose, the weathered residual rare earth ore was first grinded by planetary mill in the presence of sodium hydroxide and then leached by sulfuric acid. The influence of planetary milling on HREE recovery was investigated by assisting the leaching experiments with X-ray absorption fine structure (XAFS) in cerium and yttrium K-edge. Since yttrium was the most contained HREE in the weathered residual rare earth ore used in this study, we focused on yttrium in XAFS analysis. Results clearly showed that the recovery of HREE increased by planetary milling with sodium hydroxide. XAFS analysis revealed that a part of the yttrium in the weathered residual rare earth ore was changed to yttrium hydroxide by planetary milling with sodium hydroxide. It is supposed that all HREE were affected like yttrium due to a similar behavior observed in leaching.

Jan 1, 2018