Search Documents

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Bruno Michaux, Markus Reuter, Martin Rudolph

"It is relatively well-established in the literature that the flotation of calcium minerals using fatty acids as collector is very sensitive to the process water composition. In particular, hard waters have often been reported to strongly reduce the target mineral recoveries due to the formation of insoluble compounds such as calcium and / or magnesium dioleate, thus reducing the amount of collector available for adsorption onto the mineral surface. In this study, the flotation of a fluorite pre-concentrate was performed with tall oil, an industrial collector essentially containing fatty acids. The tests were performed in a variety of synthetic waters to simulate multiple degrees of water hardness, and to differentiate the role of magnesium and calcium ions on the flotation performance. The flotation tests revealed that, under the studied conditions, a significant difference between flotation in calcium-rich and magnesium-rich waters was observed, suggesting strong ion-specific effects in the system. Specifically, calcium-rich waters slightly improved the fluorite recovery, whereas magnesium-rich waters caused a decrease in recovery by as much as 20%. This paper is focused on the flotation kinetics aspect of the system. This approach highlighted the interesting finding that calcium ions did not simply increase the fluorite recovery, but also significantly increased its flotation kinetics. The magnesium ions, on the other hand, had the exact opposite effect.INTRODUCTIONAs the mining industry is facing an increasing number of issues related to its fresh water consumption, the idea of using alternative water sources for mineral beneficiation is gaining significant momentum. As a result, a proper understanding of the role of water chemistry in flotation is becoming more and more urgent, leading to an increasing number of studies on this topic."

Jan 1, 2018

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn't suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By M. Rudolph, D. H. Hoang, N. Kupka

"Froth flotation has been subjected to modelling since the 1930s and there is a large variety of approaches that intend to portray the entire process. Among these, three fundamental models could be considered exhaustive: the Pyke model [1], the Yoon model [2] and the Schwarz and Koh model [3]. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. Using a scheelite ore as a test case, a specific batch flotation test was repeated ten times and analyzed for chemical assays, mineralogical studies and froth properties. The detailed data are used to feed the three flotation models aforementioned in order to compare the outcomes of the three approaches, their capacity to reflect reality and to predict it. This article intends to pave the path towards reliable process models incorporating in depth mineralogy information, e.g. surface liberation, particle size and particle shape. KEYWORDS Froth flotation fundamental models, scheelite, automated mineralogy, critical assessment. INTRODUCTION In mineral processing, only three approaches aiming at describing froth flotation fundamentally could be considered exhaustive: Pyke’s collision and sliding approach [1], Yoon’s kinetic approach [2] and Schwarz and Koh’s approach [3]. The models will hereafter be referred to as Pyke model, Yoon model and Schwarz and Koh model. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. All three approaches rely on the widely accepted idea that flotation is a kinetic reaction dependent on a flotation rate constant kp, as expressed in Eq. [4]:"

Jan 1, 2018

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

By K. Haga

In this study, flotation tests were performed to investigate behavior of enargite and chalcopyrite ores from different sources synthetically mixed for separation of enargite. Flotation parameters including; pH, reagents concentration and type and flotation time were controlled to obtain an enargite concentrate with high As and chalcopyrite concentrate and final tailings with As content below 0.5 mass%. The copper ore bearing enargite mineral contained 5.87 mass% As and 16.50 mass% Cu while the chalcopyrite bearing ore contained 0.32 mass% As and 21.63 mass% Cu. The two ore samples were mixed at 7:3 (enargite: chalcopyrite) by weight ratio to prepare a mixed ore sample with arsenic content at 3.16 mass% and 18.25 mass% Cu for the flotation study. For enargite single ore flotation, the 38?75 µm size fraction showed that over 98% enargite was selectively recovered within 5 min at slurry pH of 4.0 and arsenic content in the final tailings was reduced to 0.22 mass%. In mix ore (enargite+chalcopyrite) flotation, 97% of enargite was first removed at pH 4 followed by chalcopyrite flotation at pH 8, and over 95% recovery was achieved in 15 min flotation time. Arsenic content in the final tailings was reduced to 0.1 mass%.

Sep 1, 2012

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By Vladimir F. Skorokhodov, Nikolay N. Melnikov, Svetlana P. Mesyats

"Among the problems of the civilization development, a problem of interaction between man and natural environment can be highlighted. In the twentieth century the human transforming activity had got scales of geological processes and defined the contradiction between the goal to increase the quality of human life and possibilities of the natural environment. Last twenty-five years after the World Summit on the Environment (1992) indicate that the development of civilization is still based on receiving super profits from the natural resources exploitation. This statement is confirmed by economy globalization rates, growing contradictions between consumption and production, depletion and degradation natural environment. A new technological order is formed at the time of growing world population, technological capacities, organizational complexity, from one side, and global scales of geo-resources consumption, on the other side. Sciences, determining the further civilization development, should take on the task to change the social worldview, since the preservation of human population consists in remediating and maintenance of biosphere functions as a regulator of ecological balance. The new worldview in the geo-resources exploitation is based on the Ecological strategy of mining development, which consists in reducing mining-induced loading on natural environment while increasing efficient mineral production and processing, and providing for a comprehensive solution of tasks on mineral deposit development. One of strategic trend of mining development is to increase complexity and completeness of useful component extraction from ore and mining deposits while reducing wastes and decreasing their stockpiled volumes. The implementation of the ecological strategy has shown that the future is determined by reduction of the environmental impact while improving the efficiency of mineral mining and processing.INTRODUCTION The global nature of environmental problems caused by the scale of consumption of natural resources, huge amounts of waste, and intensive man-made impact on the environment requires a revision of the strategy for the natural resources development. Many existing technologies are ineffective in achieving the ultimate goal. Direct output in the raw materials - the end product technological chain rarely exceeds 10%, which implies a huge amount of work to move the soil. In addition, the feature of scientific and technological progress at the present stage is the growth of power-to-weight ratio."

Jan 1, 2018

By Heiko Schiemann, Christoph Beyer, Thomas Pretz

"Due to multiple experiences in the field of planning and engineering of processing plants for secondary materials the Chair for Processing and Recycling of Solid Waste Materials decided to develop a software tool that supports the engineering and the planning of the basic layout of processing plants for secondary material flows. The detailed description of the material flow and its characteristic parameters is one of the main tasks to be worked out and should be considered as the basis for representative simulation results.The description of the material flow and its characteristic parameters is based on a fraction vector containing 12 material fractions. This is a compromise between a detailed material flow description and a compact and therefore time-extensive calculation model. Each material fraction is characterized by 15 parameters, which can be edited with the help of an easily accessible user-interface. In addition to basic parameters like ignition loss, water content and calorific value more parameters like the material fraction-specific particle-size distribution are contained. Using the model library SimuRec, the processing success and the recovery of complex processing plants for secondary materials can be predicted."

Jan 1, 2003