Search Documents

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By H. Clare Horwood

"Two structures, a fracture zone and a shear zone, contained the two orebodies that yielded all the ore mined at the Gold Eagle mine. The orebodies are known as the Gold Eagle vein and the No. 1 shear zone. Both structures occur close to contacts between Timiskaming sediments, Algoman diorite, and later Algoman granite-granodiorite. The structures were produced by compressive forces from a south direction acting in the southern part of the McKenzie-Gold Eagle stock and in a cylindrically shaped inclusion of Timiskaming sediments.The mine, which exhausted its ore reserves and ceased operations in September of 1941, is on the east side of Mackenzie island, in the centre of Dome township in the Red Lake area.The Gold Eagle vein was located during the summer of 1933 by a surface exploration programme carried out under the direction of Alex Gillies. Sub-· sequent diamond drilling and underground exploration led to the installation of a mill, which came into production in October of 1937. The No. 1 shear zone was discovered and explored later from a drive on the 500-foot level. The mine produced a total of 40,204 oz. gold and 19,157 oz. silver from 223,628 tons of ore hoisted (180,095 tons milled) during its 4 years of mill operation.GENERAL GEOLOGYThe ore-bearing structures trend S.61°E. across Timiskaming greywacke, Algoman diorite, and later Algoman granite-granodiorite. The greywacke is a large, cylindrically shaped mass that is separated from the mai~ mass by the later intrusives. It is a massive, light-coloured, quartzose variety that has been recrystallized by the enclosing granite. The diorite and the granite-granodiorite are early and late components of the McKenzie-Gold Eagle stock. The diorite, which is a porphyritic rock containing large crystals of andesine-labradorite surrounded by hornblende, was injected early in the Algoman period. It was intruded and in large measure surrounded by the later granite-granodiorite. This rock varies from a granodiorite near the mine to a granite in the centre of the stock. All three intrusions are massive and homogeneous."

Jan 1, 1954

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract—Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O signature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By Dennis E. Bell

"This paper describes exploration and development to 1982 in the southern half of the northeastern British Columbia (Peace River or Northeast Block) inner foothills metallurgical coal belt. Gates Formation, Fort St. John Group, is the primary target; Gething Formation, Bullhead Group, is secondary. This part of the belt remains wilderness when compared to its other parts. Practical formational and structural mapping is described. A local problem known as the Secus Mountain or Mount Belcourt conglomerates is discussed. The three major explorers have been Denison Mines, PetroCanada, and Crows Nest Resources, all with partners. Initial mine construction and rail spur construction are continuing. The new town of Tumbler Ridge is being built. Introduction This paper describes exploration and development to 1982 in the southern half of the northeast British Columbia metallurgical coal belt. The area (Fig. 1) trends 120 km northwest from the Alberta border to the Wolverine River and Bullmoose Creek. The belt averages 15 km in width, and is 20 km at its widest. Physiographically, the area is dominated by rugged inner foothills, with relief to 1,500 m. The trend of the structures is transected by a dozen rivers flowing southwest to northeast away from the Continental Divide. The Rockies, lying immediately to the west, control the climate. One fact continues to colour all coal work in the area. When compared to the other parts of the western Canadian foothills and Rockies coking belt, it remains the least accessible and least mapped portion. Lack of access also makes all work expensive. Current activity centres about two mines in construction at the northwestern end of the area. Denison Mines and partners are developing their Quintette project, and Teck Corporation and partners are developing their Bullmoose project. PetroCanada and partners have intensively explored their Monkman-Duke Mounta,in project, but mine construction awaits better economic times. The rest of the area remains lightly explored, with the exception of some intensive work on particular structures by Denison and Petro-Canada. The focus of coal work has been metallurgical bituminous coal seams contained primarily in the Gates Formation (Fig. 2) and secondarily in the Gething Formation. These formations are found in generally en-echelon structures ranging to several kilometres in width."

Jan 1, 1985

By C. Larsen, R. A. Walker, A. Voth, C. Daoust

"The 3000 t/d mill at Hernia Gold Mines Inc. was commissioned in March, 1985. By Canadian standards the concentrator is highly automated, however, unlike the retrofit systems in many other plants, the Hernia process control system was installed during plant construction. This paper describes the Hernia control system beginning with system development (justification, architecture, start up, etc.), proceeding to current applications (crushing, grinding, leaching, etc.) and finally discusses some of the short term objectives for system improvement.INTRODUCTIONThe Hernia Gold Mines Inc. operation is located in the Marathon area of Northwestern Ontario. Controlled by Noranda Minerals Inc. (50.1 %), the cost of bringing the mine into production was nearly $300 million. A unique feature of the mine development was the extraordinarily short elapsed time of three years from Noranda's initial involvement to the start of milling operations. Additional background information on this project can be found in the trade literature (e.g. Tinter (1986). Scales (1987).)The Hernia concentrator is designed to process 3000 tpd of ore and commenced operation in March, 1985. Figure 1 provides a general plant flowsheet indicating the major circuits. Typical annual production statistics are included on the figure and these have been extrapolated from the available 1987 year-to-date data. Larsen and Tessier (1986) have previously described the operational aspects of the mill.In a metaphorical sense, the Hernia concentrator is like the traditional bride, ""wearing something old (e.g. the cyanide leach process), something new (e.g. a plant wide digital control system installed during construction), something borrowed (e.g. crushers from Gaspe) and something blue (e.g. the cladding on the surface buildings). While the prospect of fully undressing this bride is of considerable interest, here we choose to focus on something new. In particular, we choose to examine the process control system in some detail since Hernia is one of Canada's more highly autcmated gold mills. The control system is of interest because it has received suostantial credit for maximizing metal production and minimizing operating costs. With reference to the latter, it is worthy of note that Hem lo reports recent operating costs of less than $100 U.S./oz."

Jan 1, 1988

By T. Robson

"A multi-seam underground mining operation employing mechanized room-and-pillar methods provides 35 per cent of Smoky River's annual ROM coal production (2 million tonnes) from the Smoky River coal field. Surface mines provide the balance. Tectonic activity, which has resulted in deformed coal seams and a rugged relief to the area, has provided natural boundaries to discrete mining areas. Coal transportation to the central preparation plant incorporates a 3 km long underground conveying system. The company is committed to efficient resource recovery and a safe and healthy working environment. Introduction The Smoky River Coal operations (SRC) are centered in the Smoky River coal field located in west central Alberta, some 360 km west of Edmonton and 20 km from the Town of Grande Cache (Fig. 1). Combined mining operations produce 2 million tonnes per year run-of-mine coal from which 1.65 million tonnes of high quality, low volatile, coking coal are obtained. The underground mining operation, employing mechanized room-and-pillar methods, provides 35 per cent of SRC's annual ROM coal production (2 million tonnes). Surface mines provide the balance. Tectonic activity has resulted in deformed coal seams and a rugged relief in the area. This has provided natural boundaries to discrete mining areas. Background Exploration of the Smoky River coal field took place over four decades commencing in 1926. McIntyre Mines Limited (parent to Smoky River Coal Ltd.}, commenced development of the property in 1968 having secured a long-term contract for the delivery of coal to Japan. Production of underground coal at Smoky River commenced toward the end of 1969 and has been continuous on the property since that time. Originally, two underground mines were opened. Original planning envisaged the use of room-and-pillar techniques to develop blocks of coal for subsequent extraction by longwall retreat mining. Following initial development, two longwall units were established, the first in November 1970 in No. 5 Mine and the second in February 1971 in No. 2 Mine. Difficulties were experienced on both units, and production commitments could not be achieved. The longwalls were discontinued, and mechanized room-and-pillar was subsequently used for all underground mining."

Jan 1, 1985

By T. T. Chen

A detailed mineralogical study was carried out to characterize the products generated in a conventional copper refinery anode slimes treatment circuit. The anode slimes, which are first leached in sulphuric acid media under an oxygen pressure to dissolve the copper and much of the tellurium, were found to contain various Ag-Cu selenides, PbSO4, Ag, Au and BaSO4. The resulting Ag2Se, Ag3AuSe2, Se, Au, PbSO4, BaSO4, SnO2 and silicate-rich leach residue is dried and pelletized. It is subsequently roasted to convert the selenium to Ag2SeO3, volatile SeO2 and water soluble Na2SeO4. The roasted product, which was found to consist of Ag2Se, PbSe, PbSO4, BaSO4, Ag3AuSe2, Au and Sn02, is smelted and refined in a Dore furnace to produce a Dore metal that contains a (Ag,Au,Pd,Cu,Pt) alloy together with traces of CuO and a Cu-Pb oxide phase. Parting plant mud shown to contain AgC1, Ag, Au, (Au,Ag,Pd), Ag2Cu2O3 and Ag20, and scrubber mud containing PbSO4 and AgC1 are also fed to the Dore furnace. The Dore furnace sequentially separates a silica slag which was found to consist of Ag, Sn02, BaSO4, Pb-Sb oxide, Fe-Sb-Ni-Cr oxide and a Pb-rich silicate phase, a soda-rich slag containing Na2CO3.H2O and Na2(Se,Te)03, and a niter slag containing Na2TeO3, Na2(Se,Te)03 and a Na-Te-Se-Pb-Ba-Cu oxide phase. The Dore metal is electrorefined in Moebius cells to yield high-purity silver and a gold mud which was shown to consist of a (Au,Ag,Pd,Cu,Pt) alloy and traces of CuO. Silver is leached from the gold mud and the resulting gold sand is cast into anodes and electrorefined in Wohlwill cells to produce pure gold.

Jan 1, 2007

By Réal Marcotte

L&apos;industrie minière représente un apport économique important pour le Québec ; cette production est très diversifiée et répartie dans plusieurs régions. Hormis les forges du St- Maurice au XVIIe siècle, l&apos;industrie minière québécoise commence en 1862 dans la Beauce avec l&apos;exploitation de placers aurifères dans les affluents de la rivière Chaudière; à la même époque, on met en production les mines de cuivre Eustis, Albert et Capelton, près de Sherbrooke1; à partir de 1881, les mines d&apos;amiante et de chromite au voisinage d&apos;Asbestos et de Thetford commencent à voir le jour. Dans les années ?20, l&apos;extraction de métaux précieux et usuels débute en Abitibi- Témiscamingue; durant les années &apos;50, le fer et l&apos;ilménite de la Côte Nord, ainsi que le cuivre de Murdochville et Chibougamau, commencèrent à être mis en valeur. Plus récemment, soit durant les années &apos;80, le sel des Iles-de-la-Madeleine et le graphite des Hautes Laurentides s&apos;ajoutèrent aux produits que nous commercialisons. Finalement, soit en 1998, le Québec devenait un important producteur de nickel avec le démarrage de la mine Raglan, au Nunavik. L&apos;exploitation d&apos;une mine peut nécessiter l&apos;extraction de grandes quantités de roches stériles, particulièrement lorsque la production se fait à partir d&apos;une fosse à ciel ouvert. De plus, étant donné que les minéraux et les métaux mis en marché ne constituent qu&apos;une fraction du minerai extrait, il faut le concentrer : on se retrouve alors avec des proportions plus ou moins importantes de résidus finement broyés. Ces deux types de rejets totalisent bon an mal an environ 100 millions de tonnes. Lorsque cela est possible, ceux-ci sont, soit valorisés comme matériaux de construction ou retournés dans leur lieu d&apos;origine afin de soutenir les murs des excavations. Toutefois, une bonne partie est accumulée en surface dans des aires aménagées spécifiquement à cette fin ; comme le montre la figure 1, la superficie utilisée à cette fin a progressé parallèlement aux booms miniers que nous venons de mentionner pour atteindre actuellement environ 15,600 hectares, dont environ la moitié sont situés sur des aires encore en activité.

Nov 1, 2002

By J. E. Dutrizac

A pyritic Zn-Pb-Cu ore waspercolation leached with acidified ferric sulphate solutions; zinc and copper were leached, lead was oxidized, but not dissolved, and pyrtte was essentially unattacked. High zinc extractions were achieved after a few months leaching, and substantial zinc solution concentrations could be produced by recycle of the oxidized solution. The leaching rate was generally controlled by the transport of the ferric sulphate oxidant. Zinc extractions increased with increasingferric ion concentration or flow rate, but were essentially independent of the concentrations of sulphuric acid, ferrous sulphate, cupric sulphate or chloride ion. The leaching rates were insensitive to the height of the ore column once a minimum height had been exceeded (0.8-1.0 m). Elemental sulphur was the principal sulphidic reaction product, but variations in the ratio of sulphur to sulphate produced anomalous temperature effects.

Jan 1, 1979

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By Pierre Labrecque

Dispatch systems have been used for open pit mining since the early 1980?s but similar systems do not widely exist for underground mining. There is a need for developing dispatch systems for underground mines, particularly highly automated operations such as block caving. An innovative method, Agent Based Modeling (ABM) for a dispatch system for a block caving operation, is proposed in this paper. The model is based on a particular behaviour observed in social insects. The focus of the ABM dispatch system is adaptability with respect to changing operational conditions and effective integration of maintenance modules with the operation. The paper will show the advantages of this innovative method compared to existing similar systems. Furthermore, the preliminary approaches for developing an agent based modeling system for block caving operations are highlighted and discussed in this paper. 1. Introduction In social

May 1, 2008

By Denis Bois

La Bolivie est un pays en développement qui compte une tradition minière qui précède même l?établissement espagnol en Amérique. Pendant toutes ces années, l?exploitation minière s?est faite sans grands égards pour l?environnement. Au cours des dernières années cependant, le gouvernement bolivien a modifié ses lois afin de rendre nécessaire la prise en compte de l?environnement dans le processus d?exploitation d?une mine. Dans le cadre d?un projet MRN-ACDI1 visant à renforcer le secteur minier en Bolivie et ses retombées pour la population, l?URSTM2 a été mandaté pour développer et mettre en place un programme académique de gestion environnementale minière, basée sur l?expertise canadienne. Ce programme vise à renforcer les institutions académiques boliviennes responsables de la formation en environnement minier en Bolivie ainsi que les ministères et agences gouvernementales concernées.

May 1, 2001

By H. Salamanca

HighService has developed different equipment using wireless technology and machine vision systems that were specially designed to allow 1) the online determination of the SAG mills liner&apos;s service life, 2) the automatic detection of a missing dipper tooth in mineral extraction shovels, 3) the reduction of accident risk potential in the mineral transportation within the mine, and 4) the reduction of collision risk potential between shovels and wheel dozers during mineral extraction. For the development of all these systems at HighService, extensive research has been done in radio frequency and image processing fields. The integration of both technologies with the expert knowledge of the company on the typical harsh environment conditions of the mining industry has led to the development of heavy duty equipment that tolerate the extreme mechanical requirements of SAG mills and electrical mining shovels.

Jan 1, 2007

By L. Jiang

The evolution of twinning in an AM30 Mg alloy was examined by uniaxial tension and compression testing at temperatures from ambient to 250°C and a strain rate of 0.1/s. The samples were cut along the extrusion direction from extruded AM30 Mg alloy tubes. Specimens deformed to various strain levels were examined by optical microscopy and electron backscattered diffraction (EBSD) techniques. The results indicate that the initial extrusion texture plays an important role in the formation of different types of twins and that the twinning behavior also depends on the strain path. Contraction and double twinning are the dominant twinning mechanisms in uniaxial tension, while extension twinning prevails in uniaxial compression. The different twinning behaviors are shown to be responsible for the sharply contrasting strain hardening characteristics of the experimental flow curves.

Jan 1, 2006