Search Documents

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By Michael Bowker

Au/TiO2 catalysts were prepared by incipient wetness impregnation and tested for the room temperature photocatalytic reforming of methanol in aqueous solution. These catalysts proved to be more active, on a molar basis, than Pd/TiO2. The dependence on loading of gold was different from that of palladium, showing a double maximum in yield at 0.1 and 2 wt. % with low rate below 0.01% and above 10%. A model is proposed for the reaction involving band gap excitation of titania electrons which are used to oxidise the methanol via adsorbed CO. With palladium, photoreforming of CO and water can be achieved, but this is much less effective on gold, presumably due to the much weaker bonding of CO on Au.

Oct 1, 2003

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By Richard Hurteau

Design and validation of an integrated guidance system for articulated ground vehicles is investigated. The development of an autonomous industrial vehicle must take into the account the specific geometry of these vehicles; they can be composed of a tractor with 1 or 2 trailers or of articulated type like LHD. Moreover the tractor-trailers type vehicles can have on-axle hitch configuration or positive/negative off axle configuration. The path-tracking of a tractor-trailer vehicle in restricted space is presented and discussed in this paper. Recent results obtained in simulation and validated by experimentation are also presented. These studies can lead to better ways of maneuvering an articulated vehicle in a restricted space or automatically executing of docking and parking maneuvers

May 1, 2002

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By Jason A. McLennan

Conditional bias is an infamous problem with estimation methods including kriging. Changing estimation parameters will mitigate, but not remove, conditional bias. The conditional bias of kriging is well understood; however, there is widespread confusion in the literature and among practicing geostatisticians regarding the conditional bias of geostatistical simulation. There is no conditional bias of simulation when the simulation results are used correctly. The correct use of simulation for recoverable reserves estimation is to (1) generate multiple realizations conditional to all available data at a small scale, (2) linearly average all realizations to the chosen block size and (3) calculate the probability of each block being ore and the ore grade of each block. The ?probability of ore? and the ?ore grade? are conditionally nonbiased.

May 1, 2002

By Bennett McLaughlin

The Penna Shaft is the deepest single?lift shaft in North America. AGNICO-EAGLE started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1 800 tonnes per day from a 2 240-metre deep shaft. Exploration success at depth lead to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7 000 tonnes per day. The use of another double drum hoist, instead of a Blair Multi-Rope winder, to hoist 24,5-tonne skips was only made possible by lowering the safety factor. This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of three kilometres.

May 1, 2003

By R. W. Thompkins

The two largest contributors to silicosis in machine men are dust from drilling and dust from blasting. With the advent of the shatter-cut method of blasting, the evils of blasting dust were greatly reduced. The problem of dust from drilling has been attacked from two different angles: (1) The adoption of dustless frontheads or enlarged water tubes, both of which have proved capable of reducing dust concentrations; and (2) The adoption of better ventilation. Many operators are loath to adopt dustless frontheads or enlarged water tubes on Leyner drills because of the increased repair costs on drills, and also because it has been found difficult to enforce 'the proper usage of dustless machines: for example, workmen sometimes plug the vents in the fronthead.

Jan 1, 1943

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By Y. Mitsuda, Y. Kayanuma, T. H. Okabe, M. Miyake

A new process to recover platinum group metals (PGMs) from automotive catalyst scrap using metal vapor was developed. To improve the efficiency of the acid dissolution process of PGMs, metal vapor of reactive elements such as magnesium or calcium were contacted with spent automotive catalyst. It was expected that metal vapor would react with metal selectively and form intermetallic compounds. The specimen of the spent catalyst was treated at 1173 K for 3 h, and it was then dissolved in aqua regia for 1 h to recover PGMs. After the reactive metal treatment, 88% of Pt, 81% of Pd, and 72% of Rh in the catalyst scrap was dissolved, while only 77% of Pt, 69% of Pd, and 38% of Rh was dissolved from untreated scraps.

Jan 1, 2004

By J. G. Pharoah

Over the last two decades a variety of models for solid oxide fuel cells (SOFCs) have emerged ranging from one dimensional (1-D) to 3-D models, from steady-state to transient models; single- and half-cell and entire stack models. A majority of these models have focused either on the transport processes or on the chemical/electrochemical processes. The approach taken by our research group is to develop a comprehensive SOFC model framework based on the considerations of detailed electrochemical reaction mechanism and by accounting for complex transport processes occurring in the porous media at the micro-scale level. In this paper, we review the state-of-the-art in SOFC modeling and identify the existing gaps that need to be filled in.

Jan 1, 2005

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990

By Vincent Jourdain

Located in the James Bay Territory of Quebec (figure 1), the Clearwater property is jointly owned by SOQUEM Inc. and Eastmain Resources Inc. Exploration on the property since the early 70's has resulted in the discovery of several gold showings. Exploration work by the joint venture since 1995 has led to the definition of the Eau Claire Zone containing an indicated resource of 540 000 tonnes grading 11.1 g/t Au (8.7 g/t Au cut at 34.28 g/t Au). Hosted by the archean Eastmain Greenstone Belt, the property geology is dominated by mafic volcanics containing thin horizons of felsic volcanics and/or sedimentary rocks (figure 2). The sequence is metamorphosed to the amphibolite facies and contains two small toalitic intrusions. Regionally, the structural trend is oriented E-W but in the area of the Eau Claire Zone a second trend oriented NE-SW is also present. The first exploration work on the property was conducted by SEREM and SDBJ from 1973 to 1976. It consisted of an airborne electromagnetic survey and a ground follow-up program on several grids. This program, comprising geological mapping, geophysics and drilling, led to the discovery of the Natel showing where a drill intersection returned 8.89 g/t Au over 2.65 m. From 1978 to 1985 the area was withdrawn from staking because of the hydroelectric projects of the James Bay. In 1985, Westmin Resources Limited and Eastmain Resources began an exploration program based on a helicopterborne electromagnetic survey. Once again, a ground follow-up program was conducted on several grids. This program included a soil geochemical survey that identified a strong (up to 10 g/t) gold anomaly. Drilling of the anomaly led to the discovery of the Eau Claire Zone where resources were estimated at 270 000 tonnes grading 6.1 g/t Au at the end of 1990. In 1995, SOQUEM Inc. took an option to gain a 50% interest on the property and obtained its interest in 1998. Since 1995, two principal mineralization zones were identified on the property. The "Rosemary Zone" consists of veinlets and disseminations of pyrite and chalcopyrite within a magnetite-rich amphibolite. The mineralized zone was identified by stripping within an area of 1000 by 500 metres. Drilling indicates copper grades up to 0.32 % Cu over 49.2 m. with locally grades of 0.75 % Cu over 5.9 m. The mineralised zone is associated with QFP dykes and corresponds to a strong magnetic anomaly and a strong copper and molybdenum soil anomaly. The "Eau Claire Zone" consists principally of a set of gold bearing quartz-tourmaline veins oriented E-W and dipping at 45-50??to the south (figure 3). More than ten different veins are recognised in the zone and up to eight veins were observed in a single trench (figure 4). The host rock between the veins shows a degree of deformation similar to the regional volcanosedimentary rocks. Each vein is hosted by a unit of actinolite-tourmaline-biotite schist up to one meter thick. The veins and their hosting schist clearly cross-cut the schistosity of the hosting lithologies and the contacts between amphibolites and felsic to intermediate rocks. Usually, the veins are less than a meter thick and are composed of quartz, tourmaline and calcite. The proportion of quartz and tourmaline varies from 0 to 80% within a single vein. The veins commonly show massive, banded or brecciated texture. Sulphides, mainly pyrite, pyrrhotite and chalcopyrite, generally form less than 5% of the vein material.

May 1, 2001

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007