Search Documents

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By S. E. Wolfe

The presence of helical ribs in smooth-bore round pipe results in the transport of granular solid particles m water at a much lower velocity than required to transport the same solids in a smooth pipe. The helical motion imparted to the flowing mixture effectively returns settled solid particles to the main stream. The flow may be stopped and restarted without difficulty. Due to the lower velocity required for satisfactory transport large power savings are realized. Also: due to lower velocity, the wear on the pipe walls is much reduced. For satisfactory performance, the ribs should have a high angle relative to the long axis of the pipe and the lineal spacing between adjacent ribs should be modest.

Jan 1, 1967

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By J. A. du Plessis, C. Dorfling

Selenium, tellurium and other precious metals (OPMs, namely Rh, Ru and Ir) dissolve in the final leaching stage of base metal refineries. Se and Te are typically removed from the copper sulphate leach solution by precipitation with sulphurous acid. Recovery of dissolved OPMs is desirable because it will reduce OPM inventory and losses. Thiourea is an effective OPM precipitation reagent, but yields insufficient Te removal. Copper is known to enhance Te precipitation when using sulphurous acid as precipitation reagent. The primary objective of this project was to evaluate whether simultaneous precipitation of Se, Te and OPMs using thiourea with metallic copper as precipitation reagents is possible. Batch precipitation tests were performed to evaluate the effect of temperature (50 – 70°C), thiourea addition (160 – 430% excess) and copper addition (2 – 8 g/L) on Se, Te and OPM precipitation. Increasing the temperature from 50°C to 70°C resulted in an average increase of 55.6 percentage points for Se precipitation and 13.5 – 23.5 percentage points for OPM precipitation. The copper addition did not have a significant impact on the precipitation behaviour. Increasing the thiourea addition increased the precipitation of Se and Te, especially when the copper addition was low; Rh and Ru precipitation also increased with up to 10 and 12 percentage points, respectively. Despite these observations, the precipitation of Se was significantly faster when no thiourea was added. It is not currently clear why thiourea appears to inhibit the Se precipitation by reaction with metallic copper. In general, Te precipitation was low (less than 30%) at the conditions investigated. Simultaneous precipitation of Se, Te and OPMs at temperatures below 80°C does not appear to be a viable option; a multiple stage operation for sequential removal of Se and Te with copper followed by OPM precipitation with thiourea would be required.

Jan 1, 2016

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By W. J. Wolfe

"THE DETECTION OF BURIED MINERAL DEPOSITS by chemical analysis of vegetation (biogeochemistry) or visual observation of plant cover type (geobotany) is based on fundamentally simple principles. The root systems of vegetation collect aqueous solutions from a large volume of moist ground below surface and act as efficient sampling mechanisms by providing a composite sample of a reasonably large area. These aqueous solutions constitute a source of ore-associated metals that may ultimately be concentrated in the upper parts of the plant. Although certain plant species have a limited ability to break down primary minerals and extract elements, biogeochemistry normally detects only metals capable of moving in solution. Metal concentrations in the underlying soil must therefore exist in a form that is immediately available for uptake by the root systems - generally in the ionic state in aqueous solution or in readily exchangeable form on the surfaces of soil clay minerals. As a result, biogeochemical responses are closely related to variables such as soil pH, Eh, exchange capacity and complexing agents that control metal mobility in the surface environment. In terms of cost, reliability and anomaly contrast, soil geochemistry will normally be more useful than biogeochemistry in locating buried mineralization in regions of residual overburden or thin transported cover. However, in areas where the root systems penetrate thick deposits of transported post-mineralization overburden, plants can provide an effective mechanism of sampling below the transported material. Biogeochemical research in Canada, Scandinavia and the U.S.S.R. has therefore focused on the potential use of plant prospecting methods (1) in areas where the upper horizons of podzolic soils do not provide an adequate response to anomalous conditions under thick deposits of glacially transported till and (2) in widespread regions of peat and muskeg terrain where near-surface mineral soils are absent."

Jan 1, 1971

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015

By A. A. Brant

ONE of the reasons advanced for the decline in prospecting and discovery is that, as regards surficial examination, the law of diminishing returns is becoming applicable. Fewer surficially unprospected fields remain; therefore, fewer discoveries by such means result. Much in the nature of mineral resources remains to be unearthed, but even now, and more so in the future, will discovery depend on painstaking petrographic and structural mapping, aided, where necessary, by judicious applications of all the complementary scientific knowledge and devices (e.g., thin section microscopy, geophysics, and drilling) that experience proves effective in localizing a mineral deposit even beneath drift, lake, or muskeg. It is to be expected, then, that the rate of discovery will decrease, that the cost per discovery will greatly increase, and that the work of discovery will become more and more the careful, methodical assembling of field data, conscientiously interpreted on the basis of scientific knowledge by trained, experienced operatives. In view of these trends, the status of applied geophysics to Canadian mining exploration and development work might well be reviewed. The niche which geophysics may occupy relative to geological surveying and drilling has been clarified by the last twenty years' experience. The cloud of somewhat justifiable scepticism that followed the 'geophysical promotion' period of the late 1920's has lifted. Mining, exploration, and finance companies, in open-minded fashion, are seeking sound advice as to what are the scope and limitations of the geophysical methods at present practised. The purpose of this paper and the following one is, therefore, as far as lies within the author's power, to review briefly the geophysical methods at present in practice in Canada, and, at greater length, to joint out impartially and critically their scope, merits, shortcomings, an possible future development. The treatment will be non-technical, the hope being that an accurate statement of the present status of geophysics in Canada may do much to result in a sounder, saner growth of what, in the future, shall undoubted} y prove an increasingly useful tool in exploration and development work. ?

Jan 1, 1942

By Yan Yang

The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year. This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant. Major modifications and improvements on the SABC circuit are described in the paper, including: 1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball. 2. Effect of milling operation parameters on milling efficiency. 3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput. 4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput. With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed.

Jan 1, 2012

By T. I. Urbancic, C-I. Trifu

"ABSTRACTSeveral case studies are presented on the use of seismic techniques to map active structures, evaluate changes in stress levels, and identify the conditions leading to large magnitude seismic events and the generation of rock-bursts in Canadian mines. The results suggest that microseismicity can be used to identify the orientation of active fractures; define regions of relatively high and low stress, and those most likely to host a rockburst; determine the role of local stress on observed shear failures; and identify the path of stress transfer associated with the remote triggering of rockbursts. Additionally, the conditions leading to rock-bursts can be characterized by a significant increase in the clustering of microseismic events along the fault plane orientation of an impending event, and an increase in the effective stress levels. It is concluded that the analysis of microseismicity provides the means for remotely monitoring rock mass behaviour as a result of mining."

Jan 1, 1997

By C. Fortin

The subject of gold flotation has been reviewed extensively in a number of publications. The focus in most of these reviews has been on the theories of gold flotation as well as the physical and chemical effects that may impact the efficacy of the gold flotation process. It is evident that the current status of gold flotation chemistry as it is being applied in industry has not been addressed widely. It is the intent of this paper to review current gold flotation practice and how these applications tie in with the current understanding of the chemistry of gold flotation.

Jan 1, 2011

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By Long Han, Beijing General Research Institute of Mining and Metallurgy, Yu Xie, Yunhai Zhang, Yangge Zhu, University of Science and Technology Beijing, Yanbo Shang, Xingrong Zhang

"The first-principles method was employed to study the adsorption of hydroxyl calcium (CaOH+) and hydroxyl (OH-) on hematite and quartz surfaces. The calculation results suggested that OH- preferred to interact with the active Fe sites on the hematite surface, whereas OH- adsorbed on the quartz surface by weak hydrogen bond. Though CaOH+ could easily adsorb on the hematite and quartz surfaces by the formation of Ca-O bond, the covalence formed on the quartz surface was apparently stronger than that on the hematite surface, meaning a stronger and more stable adsorption. CaOH+ adsorbed on quartz surface was mainly through the interaction of O-2p and Ca-3d states, and this interaction on hematite surface was weaker.INTRODUCTIONIron Increase and Silicon Reduction Technology (Yu & Duan, 2002) of hematite is mainly through the reverse flotation (silica is floated away from the iron concentrate). There are two ways to achieve this (Houot, 1983). One is to collect quartz by cationic collector directly; the other is to activate quartz by lime and then collect it by anionic collector. There are two main different views with respect to the mechanism of quartz activation: mono-hydroxyl compound theory (Fuerstenau, Rice & Somasundaran, 1965; Fuerstenau & Palmer, 1976) and surface hydroxyl precipitation theory (Hu & Wang, 1988; Wang & Hu, 1990). The former indicated the formation of the mono-hydroxyl complex is one of the two criteria of quartz flotation. The later theory, on the other hand, suggested that surface precipitation is the adsorption of active species of metallic ion on quartz surface. However, most of those researches are based on the solution chemistry of flotation and little is done at the microscopic level.In this paper, by the help of first-principles calculations, the adsorption models, bonding conditions, Mulliken charge populations and adsorption energies of hydroxyl and calcium hydroxyl ions (OH- and CaOH+) on hematite (001) and quartz (100) surfaces were investigated to find out the lime activation of quartz at atomic level, which is significant for the researches of quartz activation theoretically and practically."

Jan 1, 2016

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007