Search Documents

By G. Kordosky

The experience of one plant regarding degradation of copper solvent extraction reagents in the presence of 20 to 30 g/1 nitrate in the leach solution was described at Cobre 2003. However, little information is available about the degradation of copper solvent extraction reagents where the nitrate concentration of leach solution is much lower. Analysis of plant organic samples taken from an operating copper SX plant over a long period of time shows that small amounts of nitrate in the leach liquor can be a significant contributor to reagent degradation provided certain other conditions are present. These conditions are discussed and cautionary suggestions on copper SX plant operations in the presence of even low levels of nitrate in the pregnant leach are made based on industry experience with copper solvent extraction plants and copper solvent extraction reagents.

Jan 1, 2007

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By Barbara Kirby

Mining Industry Human Resource Council Who we are: National Sector Council for the Minerals and Metals Sector 18-person Board of Directors Over 100 Industry Volunteers PPP - Funded by HRSDC and industry What we do: Identify national HR challenges and opportunities for the Canadian mining industry Create national solutions through collaboration, partnerships and Synergy

Oct 1, 2010

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By Steve Scott

Outline of Talk Seafloor Massive Sulfides (SMS) and Seafloor Sedimentary Sulfides (SSS) Ocean mining of SMS (Nautilus Minerals) Environmental issues Summary

May 1, 2013

By D. Zagidulin

Short term electrodeposition experiments (up to 80 min.) at two current densities 220 and 275 A/m2 with varying concentrations of thiourea and glue were performed to determine the optimum levels of glue, thiourea and current density for industrial copper electrorefining. White Light Interference Microscopy was used to acquire digital images of the morphology of the electrodeposited copper. Scaling analysis was employed to pa-rameterize the morphological information encoded in the images. The limiting rough¬ness, *, the critical scaling length, Lc, and the aspect ratio, 4*/ Lc, were determined as a function of the deposition time and the amount of organic additives. These parameters were used to calculate the dynamic exponent, B, the roughness exponent, 1/z, and the as¬pect ratio exponent, y, plotted as a function of glue and thiourea concentrations. These 3D plots allowed us to find conditions corresponding to the minimum of B and y, at which the deposited copper is characterized by a small roughness and a dense structure.

Jan 1, 2007

By G. F. Trainor

At the Canadian Natural Resources Limited (CNRL) Horizon Mine they use Wenco International Mining Systems Ltd (Wenco) Fleet Management System to monitor and control their production fleet with the goal of increasing operator productivity and safety, and raising dispatcher awareness and control. Amongst the broad productivity goals CNRL wanted to achieve with help from the system was a very specific need to blend ore at the truck level. CNRL uses 25m x 25m block geological model information to represent their complex ore body. Wenco's High Precision GPS application, BenchManager provides precise graphical actual-vs-design operator feedback and system integration. Together the two companies advanced the BenchManager product to meet CNRL's needs by using live camera feeds to compare activity with data collection that ultimately lead to changes in the algorithm to include enhanced GPS indicators and the support of a GLONASS assisted solution generating distance and bearing information.

May 1, 2011

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By B. K. Mishra, Subrat Kumar Padhy, B. C. Tripathy, I. N. Bhattacharya

Manganese is a difficult metal to electrodeposit due to its high electronegativity and continues to possess unique process challenges. Manganese deposits of high quality are electrodeposited on 316 grade stainless steel from sulphate solutions in the presence of organic additives such as tetra ethyl ammonium bromide (TEABr), tetra propyl ammonium bromide (TPABr), and tetra butyl ammonium bromide (TBABr). The concentrations of these additives were examined over a relatively broad range to evaluate their effect on current efficiency, specific energy consumption and deposit morphology of the electrodeposited manganese metal. A maximum current efficiency of 68% was achieved in the presence of TEABr in the bath. X- ray diffraction studies revealed that (330) (411) planes were the most preferred planes of crystal growth during manganese electrowinning at a current density of 500 A/m2 resembling alpha-manganese irrespective of the nature of additive. Scanning electron micrographs showed smooth and uniform deposit morphologies when manganese was electrodeposited in the presence of TEABr.

Jan 1, 2014

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By Dallas W. Davis

Twin - Kennecott Deal Announced April 15, 2004 ! Kennecott earns 56% interest, if in 4 years, spends C$10 million and recovers at least 200 cts of +1 mm diamonds in all dimensions from any contiguous body ! Earn-in can take up to 6 years, but incurs stepped reduction of interest from 56% to 46% or 0% if $C10 and 200 carats not achieved ! By funding all costs through feasibility study, Kennecott earns 71% in 7 years, or, stepped reduction to 62% if completed after 8 years ! By achieving production within 10 years and funding Twin?s share of development and construction costs, Kennecott earns further 4% ! If no election to develop a mine within 2 years of feasibility study completion, Twin may present development proposal which Kennecott has 60 days to elect to follow or transfer management to Twin and dilute to 49% ! Each party has one time right to elect to market its diamond share ! On signing and annually, Kennecott will purchase $C250,000 of Twin shares at 130% of then prevailing market price until achieved earn-in

May 1, 2004

By John D. Godfrey

Precambrian Shield rocks, exposed in the extreme northeast corner of Alberta, provide the only possibility for a granitic building stone development in the province. Among a wide variety of granitoid rocks in the Shield, the Chipewyan Red Granite is one of the most favourable prospects. Geological mapping and exploration has revealed two prospective sites within a major pluton situated close to navigable water. Cleaned outcrop surfaces show clearly the pattern of joints and lithologic variations within the granite at prospective quarry sites. Other features include: basic dykes, quartz veins, and sheeting fracture zanes. Systematic orthogonally arranged fracture sets and the sheeting zanes are auributed to a tectonic origin. onsystematic irregular fractures are related to surface and nearsurface processes, such as decompression through unloading .

Jan 1, 1984

By Pascal Turcotte

_ Introduction _ LaRonde _ Controlling Instability in Haulage Drifts _ Failure mechanism in drifts walls _ Failure mechanism in drifts back _ Field Behaviour of Support Elements _ The ?Hybrid Bolt? _ Conclusions

Feb 1, 2008