Search Documents

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By S. Shimaya, T. Maejima, M. Shimo

"The authors conducted the in-situ gas-tightness tests in a fractured rock at the Namikata underground LPG storage site in Ehime prefecture, Japan. The test consisted of two independent setups, a gas-tightness test that used boreholes, and a chamber-scale test that used a horizontal drift sealed with a concrete plug. In each test, the gas pressure was increased up to the onset of the measurable gas flow to obtain the maximum containment pressure. This paper discusses the hydraulic conditions for gas leakage initiation and the importance of the pore pressure measurement for monitoring the gas-tightness of the LPG storage cavern based on the test results.INTRODUCTIONJapanese first underground LPG storage plant was constructed by JOGMEC, the Japan Oil, Gas and Metals National Corporation, at Namikata in Ehime prefecture in granitic rocks (Kato et al., 2007). The “hydraulic sealing principle” (Åberg, 1977) that utilizes groundwater flow into an unlined cavern to prevent the leakage of gas through fractures in the surrounding rock mass was employed for storage of LPG. This paper describes the results of the in-situ tests performed at the Namikata Site to obtain information on fundamental gas-tightness characteristics of fractured rock. Two types of in-situ tests, a borehole gas-tightness test and a chamber gas-tightness test, were carried out near the storage caverns. Figure 1 shows the cavern layout of the Namikata underground storage plant and the test locations. The storage facilities consist of three caverns (W26m×H30m×L485m). The cavern crown lies at a depth of 150m below the sea level in Cretaceous granitic rock (Figure 1). Water curtain boreholes excavated from the water gallery tunnel at EL-125m level are located above and side of the caverns to prevent water drainage from fractures during the construction stage as well as during operation. The borehole tests were performed from a drilling adit excavated from the eastern end water gallery tunnel, while the chamber test was conducted at the southern edge of an exploratory drift extending from the central water gallery tunnel."

Jan 1, 2015

By M. D. Everell

Le Centre de Recherches minérales (CRM), qui est un organisme de recherche appliquée du ministère de l'Energie et des Ressources du Québec, a été créé en 1969, dans le but de procurer un support scientifique et technique à l'industrie dans le domaine des mines et de la métallurgie. Pour atteindre ses objectifs, le CRM met à la disposition de l'industrie un personnel spécialisé et compétent dont une quarantaine d'ingénieurs et de scientifiques. Etant donné la nature même de l'industrie minérale, ce personnel est très versé dans l'étude des problèmes diversifiés des domaines de la technologie minière, du traitement des minerais, de la métallurgie extractive et de l'analyse minérale. Ce Centre de recherches met également à la disposition de l'industrie une usine-pilote permettant de reproduire les résultats du laboratoire au moyen d'un appareillage de type industriel, d'obtenir des échantillons en quantité suffisante pour une exploration du marché et de familiariser du personnel avec les opérations normales de l'industrie. Certaines de ses contributions récentes au développement de l'industrie minérale du Québec seront présentées.

Jan 1, 1985

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By D. Berkley

The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity. This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remote located industrial facility. It is addressed to the ?users? of cogeneration facilities rather than to ?generators.? The focus is on analyzing various site-specific design considerations to pre-screen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project. Part 1 of this paper (Berkley, 2003) provides a basic understanding of cogeneration plants of various types to establish a common language. Part 2 outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants.

Mar 1, 2003

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing &apos;with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale&apos;s of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By J. R. Goode

"Canada developed pioneering rare earth solvent extraction methods to recover the rare earths and thorium as by-products of uranium recovery operations in Elliot Lake, Ontario, and was a major supplier of these key elements from about 1960 until 1990. At one stage, Elliot Lake was supplying perhaps one third of the world’s yttrium as well as much of its thorium. This paper reviews the development of Canada’s early rare earth and thorium production facilities. INTRODUCTIONThe rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960s the invention of rare earth-based phosphors for the cathode ray picture tube used in colour television sets launched a major demand for certain rare earths.The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths.Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available but unquestionably Elliot Lake made a significant contribution to world thorium and the rare earth production. This paper, presented earlier in an abbreviated form (Goode, 2012), is intended to present as much of the information that is available."

Jan 1, 2012

By J. E. Carrasco, J. D. Stinnette, R. A. Alvarez

"Chuquicamata Underground Mine is one of the main projects for the Chilean government copper company (CODELCO). Underground mine project has been under construction since 2013 and presents a solution for the lower production levels of the open pit and prolongs the life of the mine for the next 40 years. Currently, around 2000 workers operate in the mine daily. Dozens of trucks and heavy machines drives through all main routes and access in the mine. As a mine under construction not all the infrastructure necessary to operate safely in the mine has been completed. Risk of a truck or fixed facility fire is always a challenge to keep under control. One important part of fire simulation relays on what we can do prevent a fire and what can be done with the existing infrastructure to control a declared fire and start evacuation plans. This study has been made as a feasible emergency plan to implement, in this case, of a mine under construction, were limited resources are available. Several fire scenarios have been made to support all the emergency plan strategy and a detailed step by step procedure indicates what the elements of a fire emergency plan and risk analysis are.INTRODUCTIONThe main objective of this study is to describe the importance of fire risk analyses (FRAs) and different methods to be used before commencing fire simulation and methodology steps utilized for a fire emergency plan strategy (EPS) at the Chuquicamata underground mine. It also describes how to classify zones which are going to be affected by fumes and gases propagation derived from the exact location of a fire event. Fire simulation study is helpful to determine the impact on a ventilation system with the main purpose of providing relevant information to complement emergency plans and stablished control techniques in ventilation design and its operation. Most fire simulation studies only concentrates in simulation techniques on itself. But what is the next following step in developing an emergency plan? How can we evaluate, classify and treat risky areas? This study is focused mainly in the phases before and after a fire simulation process. Phases corresponds to a good FRA and how output data can be used for an EPS."

Jan 1, 2019