Search Documents

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By Peter Price

Introduction The Horne mine, the property of Noranda Mines, Limited, has in the last six years become one of Canada's leading gold and copper producers. Since the smelter was blown-in during December, 1927, up to the end of 1933, it has produced approximately 1,200,000 oz. of gold and 35O,OOO,OOO lb. of copper. The property is situated within an area occupied entirely by pre-Cambrian rocks and characterized by the complexity of rock types and structures common in such terrain. But apart from this the mine also presents other features of unusual interest in the size, number, and variety of the ore-bodies, the mineralogical associations, and the rather exceptional values both in gold and copper. It is not surprising, therefore, that a study of the geology of the mine should bring to light many interesting problems. The present paper summarizes, as concisely as possible, the results of such a study. Actually, it is a much abridged version of a more comprehensive and detailed paper completed by the writer a year ago (1), but embodying certain corrections and additional data made possible as a result of further development at the mine and of field work carried out during the summer of 1933. Owing to limitations of space, the paper is, in the main, a presentation of conclusions arrived at in the course of the study. Much of the supporting evidence cited in the thesis referred to has, of necessity, been omitted here.

Jan 1, 1934

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By D. A. Rhys

"The Red Bluff porphyry is a tabular 2 km long north-west trending Early Jurassic quartz diorite to monzodiorite body that intrudes a folded Triassic greywacke sequence in the lskut River area, northwestern British Columbia. The porphyry is 500 m to 800 m northeast of the Snip orebody, which is a southwest-dipping shear-vein, termed the Twin zone that contains approximately 35 tonnes of gold.The intrusion associated with the mineralization is characterized by 0.3 cm to 4 cm phenocrysts of K-feldspar in a mediumgrained plagioclase porphyritic matrix. It is overprinted by pervasive sericite + quartz ± K-feldspar ± biotite (potassic) alteration characterized by intense stockworking of quartz veins containing magnetite--hematite bands. This assemblage is cut successively by quartz veins with minor iron-oxides and pyrite, and by younger pyrite veins with phyllic envelopes. The system is gold-rich but copper-poor, with typical grades between 0.25 g/t and 0.6 g/t Au, and 0.1% and 0.2% Cu. All styles of alteration and veining have similar abundances of these metals. Where southwest- and north-east dipping shear zones are developed in the porphyry, veins of all types are sheeted and foliation parallel. These sheeted zones are interpreted to be syntectonic. Asymmetric phenocrysts, folded veins and oblique foliations developed in the 130 haulageway of the Snip mine imply oblique normally-directed shear on the southwest-dipping foliation.The adjacent Twin zone is a high-grade auriferous shear-vein system that is internally banded with: (1) carbonate-chlorite-biotite veins, with textures indicating formation at least partially by wallrock replacement, and (2) dilatant quartz-sulphide veins. Veins commonly have potassic alteration envelopes that contain biotite ± calcite ± K-feldspar. The zone is highly deformed and schistose, with numerous kinematic indicators including shear bands, asymmetric folds, rotated porphyroclasts and oblique foliations that indicate a normally-directed shear sense which is parallel to that indicated by fabrics within the porphyry.Precious and base metal veins within 2 km or 3 km of the Red Bluff porphyry are zoned. Veins and shear-veins proximal to the intrusion, such as the Twin zone, are typically enriched in gold, copper and molybdenum, and have potassic alteration envelopes dominated by biotite. Distal veins usually contain relatively abundant zinc and lead and have sericitic alteration envelopes. Structures of both types have an Early Jurassic galena Pb-Pb isotope signature.The similarities in structural fabrics and alteration histories in both the Twin zone and the porphyry, the zoning of the vein systems in the area, and the apparently concordant Early Jurassic zircon U-Pb age from the porphyry and galena Pb-Pb dates from the Twin zone and surrounding vein systems suggest that intrusion, semi-brittle deformation and a large mineralizing hydrothermal system were closely related temporally and genetically."

Jan 1, 1995

By J. G. Manchuk, M. Thurston

"The degree of uncertainty associated with a natural diamond resource is important to quantify from the time of discovery through the production lifetime. Data collection occurs during the discovery, exploration, delineation, and production or recovery phases. Quantifying the relationship between data and uncertainty is an important component of project valuation. The value of data is measured as their potential to reduce uncertainty if they are collected. A method is developed using Monte Carlo simulation for predicting resource uncertainty and valuing data during critical phases of development, particularly discovery and exploration. The technique is applied to diamond pipe deposits.RÉSUMÉ Il est important de quantifier le degré d’incertitude associé à une ressource diamantifère naturelle, depuis le moment de sa découverte et durant toute la durée de l’exploitation. La collecte de données se fait durant les phases de découverte, d’exploration, de délimitation, et de production ou de récupération. La quantification de la relation entre les données et l’incertitude est une composante importante de l’évaluation du projet. La valeur des données est mesurée en tant que leur potentiel à réduire l’incertitude si elles sont recueillies. Une méthode a été développée qui utilise la simulation de Monte Carlo pour prédire l’incertitude de la ressource et évaluer les données durant les phases critiques du développement, surtout celles de la découverte et de l’exploration. La technique est appliquée à des gisements de cheminées diamantifères."

Jan 1, 2015

By Clifford S. Gibson

THE Workmen's Compensation Ace defines Silicosis as "a fibrocic condition of the lungs caused by the inhalation of silica dust sufficient co produce a lessened capacity for work". This fibrocic condition muse exhibit a specific appearance in the X-ray picture of the chest-an appearance which is not characteristic of several lung conditions which can cause lessened capacity for work and which are not due co silicosis. The layman is sufficiently familiar with this subject co know chat, as far as our knowledge goes, quartz is one of the principal objectionable factors in the production of this condition. He should also know that silicosis respects neither geographical nor industrial boundaries. It is as much a factor in some industrial processes (e.g. foundry work, sandblasting) as it is in mines handling ores containing quartz. Its development co a recognizable stage is usually a matter of many years. As yet, its cure is unknown. Its prevention is possible in varying degrees. The layman should also know that the development of fibrosis may be accelerated by breathing in, or living in, any atmosphere containing dust. Few normal adults, particularly those above a certain age, have clear lungs, and fibrosis in varying degrees is noted in the farmer, the steel worker, the clerk, and many others in varied occupations. It is not restricted to miners. Medical and industrial journals, and at times the press, are crammed with data pertaining to this subject, much of which is misinformation. This is particularly true of certain !laces where the preventive and compensation measures for the good o those earning their livelihood in an industry in which silicosis may be contracted are not so far advanced as in our own Province. A great many of these publishings are alarming to the layman. They leave him with the impression that he is taking his life in his hands if he elects to work underground, particularly in a gold mine-that he has at once sold his heritage of health and chat sooner or later he will succumb to the ravages of this ailment. Nothing could be farther from the truth. Actually, under present conditions in Ontario mines, a very small percentage of the men employed ever become impaired by silicosis to the extent chat they must withdraw from the industry. I propose to tell you briefly something of this subject as it affects our mines.

Jan 1, 1937

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

By T. Liu, C. Shi, T. Fu, M. Zhong

Water inrush in coal mines is induced by the imbalance of the groundwater flow field and the engineering geo-mechanics field. Therefore, to prevent water inrush it is important to predict the critical hydraulic pressure of water inrush in coal seam floors. This paper will investigate a method for conducting theoretical forecasting of the critical hydraulic pressure of water inrush in coal seam floors by adopting the combination method of a genetic algorithm-neural network. First, the topology structure of a neural network (NN) based on genetic algorithms (GA) will be determined and then the critical pressure of water inrush in a coal seam floor using the chosen NN will be predicted. Finally, theoretical forecasting results will be compared with actual measurement results to determine the feasibility and applicability of this method.

Jan 1, 2008

By A. G. B. Hayes, C. L. Renzoni

"AbstractThis paper provides a rough outline of economic expectations for the near future and then goes on to discuss their effect on the expected demand for metals, using zinc, copper, nickel and aluminum as detailed examples.IntroductionMINING, as you are all painfully aware, is a cyclical business. We believe that it will remain so as long as there are economic cycles.The fortunes of the industry are tied to those sectors of the economy where decisions can be postponed until more favourable times: automobiles, housing, appliances, inventory building and capital spending. Over the past two years, while U.S. GNP fell by 3.8%, automobile production declined by 31 %, from 9.7 million units in 1973 to 6.7 million in 1975. Housing starts plummeted some 43% from 2.1 million units in 1973 to 1.2 million in 1975. Little wonder that U.S. copper consumption fell by 37% and zinc consumption by 38% over the same period.With the rest of the world's economies moving in unison with that of the United States, it is also not surprising that times have been tough for mining.Arthur Burns, chairman of the U.S. Federal Reserve, contends that each recession sows the seeds of its own recovery. The worse the recession, the better the subsequent recovery. If this is true, then the lot of the mining industry should improve significantly over the next two to three years."

Jan 1, 1977

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By C. R. Ross

"THE ASSESSMENT of pneumoconiosis-producing dusts in mines and other industries is usually undertaken for one or more of three reasons: (1) To compare dust exposures at particular operations with standards of permissible dustiness in order that hazards may be evaluated and preventive procedures initiated where required.(2) To study particular operations with the objective of improving dust control devices or procedures by locating dust sources. (3) To obtain data which, along with the results of medical investigations, may assist in understanding the causes of dust-induced diseases or aid in the establishment of permissible standards of dustiness. Most dust measurements are made for the first of these reasons -to evaluate dust hazards so that they may be controlled. For this purpose, four quite different assessment techniques have been in widespread use for many years. One of these is based on the konimeter, an instrument familiar to most .Canadian mining men; a second on the impinger, which is also widely used in Canada, and almost exclusively so in the United States; a third on the thermal precipitator, used extensively in Britain and South Africa; and a fourth on the tyndallometer, a light-scattering instrument used in Germany."

Jan 1, 1960

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By T. Grammatikopoulos, SGS Canada Inc.

"The Nechalacho rare metal deposit, located in the Northwest Territories, Canada, is currently being taken through Feasibility Study by Avalon Rare Metals Inc. QEMSCAN analysis and supplementary electron microprobe analysis were utilized to identify and quantify the mineralogy of the deposit, and determine REE distribution among the minerals. QEMSCAN mineralogy was performed to provide textural information on the mineralization, determine the variability of the ore and identify REE domains, and the liberation and association of the REE minerals. The sample matrix consists predominantly of silicate minerals. The REE minerals include allanite, monazite, synchysite, columbite, fergusonite, and bastnaesite. Zircon is present in considerable amounts and is a REE carrier. Fergusonite and zircon account for most of the HREE, and monazite, allanite, synchysite and bastnaesite the LREE. QEMSCAN mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data are implemented to define the mineralogy of the ore body, support metallurgical test work, and predict recoveries and grades.INTRODUCTIONThe term rare earth elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties.Economic and potentially economic REE deposits form two main groups, a more commonly occurring “light rare earth element” (LREE) group containing lanthanum, cerium, praseodymium, neodymium, and samarium and a less commonly occurring “heavy rare earth element” (HREE) group which, in addition to the LREE, contains elevated concentrations of the more valuable REE, europium, gadolinium, terbium, dysprosium, holmium, yttrium, erbium, thulium, ytterbium, lutetium and scandium. The first group is hosted primarily by carbonatites and the second by highly alkaline (Na + K > Al) silicate igneous rocks. The LREE are produced mainly from bastnaesite, monazite, etc., while HREE are produced almost exclusively from low-grade secondary ion adsorption clay deposits in which the REE are adsorbed onto the surfaces of kaolinite and halloysite, clay minerals produced by the weathering of granite and sediments. HREE are also found in fegusonite, zircon, xenotime, etc but are not produced presently from these minerals. China is responsible for 97% of the World’s production of the REE, mainly from the giant Bayan Obo, carbonatite-related deposit and from the clay deposits mentioned above.Quantitative automated mineralogy is increasingly being applied to ore deposits. It helps users to understand and improve mineralogical parameters for geological and metallurgical purposes. Data include textural characterization, to quantification and distribution of ore and gangue minerals, liberation and association of the REE minerals. The data can be used to define mineralogical domains and predict the metallurgical response of the ore (Gunning, de Souza, & Grammatikopoulos, 2009)."

Jan 1, 2012

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada's iron production was 1.85 per cent of the world's output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada's iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978