Search Documents

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By Terry Keough

Contents for discussion ?Current liner technology ?Innovation of magnetic products ?Development of magnetic wear liners ?Installation and change out method ?Uses and capabilities ?Internal wear liners ?Summary Vulcanized rubber ?Many of you are familiar with using vulcanized rubber to provide wear protection on mining equipment. For years, this was the standard for most mining equipment, and mines spent a lot of money fabricating and lining steel equipment.

May 1, 2010

By Nn Li

Energy consumption in commercial buildings has been increasing rapidly in the past decade. The knowledge of future energy consumption can bring significant value to commercial building energy management. For example, prediction of energy consumption decomposition helps analyze the energy consumption patterns and efficiencies as well as waste, and identify the prime targets for energy conservation. Moreover, prediction of temporal energy consumption enables building managers to plan out the energy usage over time, shift energy usage to off-peak periods, and make more effective energy purchase plans. This paper proposes a novel model for predicting heating, ventilation and air conditioning (HVAC) energy consumption in commercial buildings. The model simulates energy behaviors of HVAC systems in commercial buildings, and interacts with a multiagent systems (MAS) based framework for energy consumption prediction. Prediction is done on a daily, weekly and monthly basis. Ground truth energy consumption data is collected from a test bed office building over 267 consecutive days, and is compared to predicted energy consumption for the same period. Results show that the prediction can match 92.6 to 98.2% of total HVAC energy consumption with coefficient of variation of the root mean square error (CV-RMSE) values of 7.8 to 22.2%. Ventilation energy consumption can be predicted at high accuracies (over 99%) and low variations (CV-RMSE values of 3.1 to 16.3%), while cooling energy consumption accounts for majority of inaccuracies and variations in total energy consumption prediction.

Aug 1, 2013

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

By M. Helinski

In the authors? experience inappropriate water management in hydraulic fill masses has been the root cause of most barricade failures. Inappropriate water management can lead to high water pressures, reduced effective stresses and increased barricade stresses (Kuganathan 2002). In addition the high hydraulic conductivity and non-plastic nature of most hydraulic fills makes susceptibility to piping failure (Cowling et al. 1987) a high possibility in many hydraulic backfills where a static water head is available. In order to avert both of these failure mechanisms it is essential to control the elevation of the phreatic surface within the fill mass. This is usually achieved through campaigned filling and resting periods. The duration of filling and resting periods are often estimated using some form of stope drainage simulator. Due to the random nature of many characteristics that influence the fill mass hydraulic conductivity, simulation of hydraulic fill drainage can be difficult. The high consequences of inaccurate phreatic surface estimates combined with the high variability in drainage properties often results in operators taking a conservative approach to this modelling. This conservative approach can lead to significant delays in the filling cycle which can have a major impact on the productivity of many hydraulic fill operations and can often results in an unnecessary movement towards capital intensive paste fill systems. This paper presents a water management technique which combines a simplified drainage model with in-situ monitoring to provide a rational approach to water management. With an accurate drainage model filling operations can be carried out at optimum efficiency without compromising safety. The implementation of this strategy has lead to a significant increase in filling rates at a number of Australian filling operations. A brief case study from one of these sites has been presented.

May 1, 2007

By Luis A. Tondo

The Paracatu Expansion Project III in Brazil was implemented between 2006 and 2008 to increase the existing capacity from 20 to 61 Million tons per year of gold ore treatment. This expansion led the Brazilian subsidiary of the Canadian Kinross Gold Corporation to become the single largest gold producer in Brazil and the largest single gold concentrator in the world, with a nominal capacity to treat around 167,000 tons per day of ore. This paper describes the Project Development areas for the Paracatu Expansion, using the approach proposed by the Project Management Institute (PMI) and the methodology included in the PMBOK (Project Management Book of Knowledge). The author has more than 20 years of experience in the gold mining industry, having worked as a plant metallurgist, mill superintendent and development manager for RPM until he took the position as the Project Manager of the Paracatu Expansion III in 2005. Luis Tondo has a BSc in Mining Engineering from UFRGS-Brazil, an MScEng from the University of Queensland - Australia and an MBA degree from FDC-Brazil. Luis is currently based in Santiago-Chile, acting as the Project Director for developing projects in Latin America for the Kinross Gold Corporation.

May 1, 2009

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By P. K. Naik, B. Das

Flotation studies were carried out to recover carbon values from blast furnace flue dust containing ~30.34% carbon, 4.6% volatile matter (VM), and 65.03% ash. The variables chosen for the experiments were dispersant (sodium hexametaphosphate), pH, collector (diesel oil), and frother (MIBC). The experiments were designed according to a 24 full factorial design method and regression equations for the recovery of carbon and product grade were determined from the data. Experiments were performed to optimize recovery and grade using the steepest ascent method. The maximum recovery of carbon was 90.0% with a concentration of 56.5%, whereas the maximum obtainable grade of carbon was 66.35% with 50.45% recovery.

Jan 1, 2005

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

By H. P. Jacobi

"The last 25 years have seen tremendous economic pressure placed upon the base metal processor. Industry has responded with technological innovations that have contributed to significant reductions in capital and operating costs. Major changes in processing machinery and philosophy are highlighted for the main unit operations of a base metal mill. Changes in our attitudes on what is environmentally acceptable are also discussed.INTRODUCTIONNewton's law of motion paraphrased states that nothing will change unless there is a pressure to do so.Aase metal processing as a primary commodity related industry has been under severe economic pressure over the last 25 years. This has been brought on by over capacity from new operations in the L.D.C. 's, through material substitution in a host of traditional base metal applications and generally reduced world-wide economic activity. In addition to shrinking markets our collective environmental consciousness has raised effluent standards and workplace hygiene and the employee's as well as government's economic expectations of how much ought to be derived from ''nature's riches''.Industry has responded with technological changes which, it was hoped, would counteract the cost squeeze in which it found itself.I would like to briefly enumerate the major changes, as I see them, that have taken place in the main unit operations that form the normal processing chain for base metals.While the following paper will mention several brands of products, I would like to emphasize that these are the ones that I am most familiar with and is not to say that they are the only manufacturers which have contributed to changes. In fact it ls fair to say that all makers of mining and processing equipment have made improvements to their products, to a greater or lesser degree; they have had to, to still he in business in 1986."

Jan 1, 1987

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By Christoph Müller

Information exchange for mine process optimization is essential. Today, modern mining equipment uses the IREDES standard to exchange production plans and reports for easy management and storage. To gain further benefits from process optimization, a mine wide access to real-time information is needed as e.g.: The current status of a machine, operational details etc. Presently, real-time data exchange systems are developed by machine producers. Each machine producer uses its own way of gathering, managing, and storing production data. These proprietary mining processes increase the complexity of cross platform data exchange and management for mines which involves machines produced by different vendors. Casting and unifying the data requires much effort. For this purpose, ?IREDES On-line? currently is being introduced. The standard defines an open, web based method for the exchange of volatile real time machine information. Two different principles are used: Web Services for cross platform information exchange within the IT world and the optional OPC UA for use with automation and process control systems. With such a standard information from machines of different vendors may be managed by using one common platform without spending the effort for dedicated interface development. Additionally, information management and storage will become straight forward since all the data are of the same format. The IREDES On-line standard utilizes the latest IT technologies as well as the knowledge and experiences gained from the previous IREDES standard. The paper explains the benefits, the use, as well as the technical design of the standard and gives application examples from the practice.

Oct 1, 2009

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By L. S. Urbanoski

This presentation describes a major modernization project at the Geco concentrator. The objectives of the program were to replace obsolete flotation equipment and upgrade process controls.Noranda Minerals Inc. — Gecc Division is located at Manitouwadge in Northern Ontario. The community is situated north of Lake Superior approximately equidistant from Thunder Bay and Sault Ste. Marie.Milling operations began in September, 1957. The mill processes a complex base metal ore by differential flotation techniques to produce copper, lead and zinc concentrates. To date some 43 million tons have been milled, qualifying Geco as a rather major base metal deposit.II. BACKGROUND:The Geco concentrator was designed and constructed in the mid 50's. A number of features specific to a concentrator of that vintage provided the justification for the modernization efforts described herein.Firstly, the mill was constructed without any instrumentation, not even pneumatic controls. Solid state electronics, computers and related instrumentation were unheard of, or rather primitive by today's standards.Secondly, some of the major equipment, in particular the flotation equipment, did not compare favourably to that in use today. MacIntosh flotation machines (more commonly known as Mac cells) were installed at Geco. These cells were prevalent in a number of concentrators built by Noranda, including Quemont Mining Corporation Limited, Gaspe Copper Mines Limited and Noranda — Horne Division. The Mac cells were used for copper and zinc rougher and scavenger operations. Some units were also installed for a pyrite recovery circuit that was never operated. In total, 104 Mac cells were installed in the main flotation area of the concentrator.

Jan 1, 1987