Search Documents

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

It is not often that mines have as much warning of the approach of bad ground conditions as was the case at the Western Mining Corporation, Kambalda Nickel Operations Lafranchi/Schmitz Decline. Most aspects of this operation are in fact quite unique and like the best solutions, the answer to the problem of weak and foliated ground conditions was relatively simple; requiring the use of readily available explosives although the idea of using it in this manner may not be the most obvious.The use of high shock energy POWERGEL 2131 cartridges proved to be the correct answer, in conjunction with small changes in drill pattern design. The resulting lack of overbreak bears testimony to the success of the concept and the commitment of the miners to achieving a safe working environment.

Jan 1, 1992

By Whitford DJ

A distinct zonation occurs in the nature of submarine volcanic activity associated with westwards propagation of the Woodlark spreading system into continental crust. Olivine tholeiites (Type I MORB) flooring one spreading segment in the Eastern Sector of the Western Woodlark Basin are accompanied by more evolved "ferrobasalts". Basaltic andesites and Mg-poor andesite-dacites occur on axial and flanking seamounts respectively. In the Western Sector, Mg- and K-rich olivine andesites occur in a rift valley and on an axial seamount near the tip of the propMr/8 tig rift. Observed correlations between 6Sr ratios (0.7028-0.7041), REE patterns and K contents imply a complex petro- genesis with the relative importance of mantle heterogeneity and crustal contamination difficult to resolve.

Jan 1, 1987

By Tran T, Young D

During the processing of gold, effluents that are discharged into the tailing dams contain free cyanide, metal cyanide complexes of zinc, copper, iron, etc and their oxidised products such as ammonia, cyanate and thiocyanate. A knowledge of how different cyanides behave in the solution is vital to metallurgists working in the area of cyanide waste treatment. Although the free cyanide ion is not stable in aqueous solutions and is expected to degrade in a natural environment by atmospheric oxidation, the metal cyanide complexes, especially of iron, are very stable. The CHEMIX program from the THERMODATA package, developed by the CSIRO Division of Mineral Products, was used to evaluate various copper-cyanide and iron-cyanide systems. The simulation of these systems show how the free cyanide and cyanide complexes behave at different conditions of solution composition and acidity (pH).

Jan 1, 1991

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

Records of ex-solution intergrowths with tetrahedrite as a component are rare. Intergrowths of this nature of tetrahedrite with galena have been described by Guild (1917) and Schneiderhohn (1922), and in Broken Hill ore by Stillwell (1926), but both Schneiderhohn (1922) and Gruner (1929) have commented specifically on the apparent absence of exsolution intergrowths of tetrahedrite and chalcopyrite, despite their frequent association in ores, and their related atomic structures. Schwartz (1942), reviewing the literaturerelating to ex-solution among ore minerals, lists only two instances of such intergrowths, one an occurrence of lamellae of chalcopyrite oriented along the octahedral planes of tentantite (the arsenical isomorph of tetrahedrite), the other of blebs of tetrahedrite in stannite. The only other possible instance of such intergrowths known to the author is the record of "pseudoeutectic" intergrowths of tetrahedrite with chalcopyrite and with bornite in a silver pitchblende ore from the Great Bear Lake district of Canada (Furnival,1939).Some interest attaches, therefore, to the two occurrences described below of tetrahedrite showing ex-solution relationship, in one instance with chalcopyrite, and in the other with bornite.TETRAHEDRITE-CHALCOPYRITEAn intimate intergrowth of tetrahedrite and chalcopy-rite, apparently the product of unmixing of a solid solution of...

Jan 1, 1946

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By Jia X

Three-dimensional microscopic modelling techniques involving specific calculations based on direct computation of the Brownian, van der Waals, Born, electrical double layer repulsion, bulk, hydrodynamic and external forces (gravity, magnetic etc) acting on and between each particle in a mineral dispersion are now feasible using advanced computer processor architectures. This contribution surveys the hardware requirements, the advantages and limitations of the approach for enabling prediction of dispersion behaviour a priori. The notion of developing a generic particle simulator, akin to the use of molecular modelling in the area of drug design, based on inputting process-relevant data (solution chemistry, mineral solids properties, hydrodynamics etc) is discussed. The methodology is illustrated with application examples involving: predictions of coagulation of mineral fines; shape and size of magnetically-flocculated hematite; and the kinetics of fouling of membrane surfaces and walls.

Jan 1, 1993

This paper provides an overview of current and future mine developments in the major island nations Indonesia, Papua New Guinea (PNG), New Zealand, and Fiji, and the French territory of New Caledonia. Many of the other 11 small island nations in the region, such as Vanuatu, Pulau and the Solomons have been the subject of considerable exploration orientated towards gold in the past few years but without any deposit found with confirmed economic viability.

Jan 1, 1990

By Kubo H, Kubita K, Morinara M

A quantitative method for predicting the mechanical properties of zinc alloys is proposed on the basis of the molecular orbital calculation of electronic structures. A new parameter which is the s-orbital energy level, Mk , of alloying elements in zinc was introduced into this method. This Mk parameter correlates with the electronegativity and the atomic radius of elements. The compositional average of this parameter varied linearly with the tensile strength and the hardness of commercial alloys and some alloys developed by Mitsui. This electronic method was very convenient in designing high performance zinc alloys efficiently.

Jan 1, 1993

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By Krouse RH, Aleinikoff JN, Nokleberg WJ, Church SE, Newkirk SR

A belt of volcanogenic massive sulfide (VMS) deposits and occurrences extends for over 150 km along the southern margin of the Yukon-Tanana terrane in the eastern Alaska Range. The VMS bodies occur mainly in the Jarvis Creek Glacier subterrane (JCGS), one of the highest structural/ stratigraphic levels of the Yukon-Tanana terrane. The JCGS consists of a VMS--bearing metavolcanic rock member and a metasedimentary rock member. The VMS deposits and enclosing rocks exhibit two periods of regional metamorphism.From northwest to southeast, the major VMS districts are the Bonnifield, Hayes Glacier, McGinnis Glacier, and Delta districts. The Bonnifield, Hayes and McGinnis Glacier district sulfide bodies consist of pyrrhotite and lesser amounts of pyrite, chalcopyrite, with or without arsenopyrite, sphalerite and galena. The larger, 800 km Delta district deposits and occurrences contain variable amounts of pyrite and pyrrhotite and lesser amounts of primarily chalcopyrite, galena, sphalerite, and arsenopyrite.The sulfide accumulations are interpreted as Kuroko-like deposits that formed along the submarine volcanic part of a Devonian, continental-margin igneous arc. U-Pb isotopic data from zircons from the metavolcanic rocks indicate an age of about 370 Ma (Devonian). 207Pb/204Pb ratios for sulfides from the districts are similar and indicate lead was in part derived from first cycle sediments eroded largely from Precambrian crystalline rocks. 207Pb/204Pb ratios from feldspars in Devonian metavolcanic rocks are similar to those in sulfides, and indicate incorporation of radiogenic Precambrian lead into the Devonian magmas. A Precambrian crystalline source for quartz in metasedimentary rocks is indicated by 2.3 Ga old zircons. Common-lead isotope studies of igneous phenocrysts in metaigneous rocks and sulfides in volcanogenic massive sulfide deposits indicate a unique isotopic signature. The data permit an exotic origin of the Yukon-Tanana terrane with respect to North America.

Jan 1, 1990

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Burgess J, Brownrigg A

The world steel industry underwent rapid growth from 1950 to 1970. Since that time, production growth has been relatively slow, with declining production in the developed countries and increasing production in some newly developing countries. Since 1970, Western World crude steel production has been static at around 450 million tonnes, with cycles around this level in a 100 million tonnes band.

Jan 1, 1992

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By M H. Mian

Much has been published on resuspension of sediments in lakes and estuaries. In general, resuspension has implications on transport and release of contaminants from the sediments. It has been shown that wind-induced waves contribute to erosion of sediments, which are then distributed to various sections of the water body by currents. Empirical equations formulated on the basis of cohesionless sediment behaviour have been applied to the design of a few tailings ponds in different parts of the world, especially in the selection of the necessary depth of water to minimise negative environmental impacts. The paper highlights the shortcomings inherent in these equations using field-measured data from a tailings site in Canada. Laboratory measured tailings properties are used to identify critical shear stresses required to initiate tailings erosion. The influence of cohesion on resuspension of fine-textured tailings is discussed.

Jan 1, 2003